AUDIOPHONICS DA-S250NC Class D Integrated Amplifier User Manual

June 13, 2024
AUDIOPHONICS

AUDIOPHONICS-LOGO

AUDIOPHONICS DA-S250NC Class D Integrated Amplifier

AUDIOPHONICS-DA-S250NC-Class-D-Integrated-Amplifier-
PRODUCT

Product Information

Model DA-S250NC
Introduction Audiophonics DA-S250NC is an integrated amplifier.
Package Content 1x Audiophonics DA-S250NC amplifier, 1x Remote control, 1x

Antenna, 1x Power cable, 1x User manual
Warranty| Two years warranty from the date of delivery. Covers
manufacturing defects.

Product Usage Instructions

  1. Connect the amplifier’s power supply connector (13) to a power outlet using the supplied power cable.
  2. Press the power button (14) on the amplifier.
  3. The LED on the ON/OFF button (1) will light up red.
  4. Press the ON/OFF button (1) on the unit or the ON/OFF button (15) on the remote control to switch on the amplifier.

Introduction

Thank you for purchasing this Audiophonics DA-S250NC integrated amplifier. We strongly recommend that you read this manual thoroughly before use. This way, you will be aware of all the possibilities of the device’s operation, while avoiding any potential misuse of it. You will protect yourself and the device from possible damage caused by improper use. Keep this manual for future reference.

Usage and safety advice

The Audiophonics DA-S250NC amplifier complies with all the directives and standards imposed by the European Union.
Caution: Never touch the inside of the device during or after it has been powered. If you mishandle it, you could suffer a serious electric shock.

Please observe the following points carefully:

  • The unit is designed for indoor use only. Protect it from water splashes, high humidity, and excessive heat.
  • Under no circumstances should you place objects containing liquids on the unit.
  • The heat from the unit must be dissipated by adequate air circulation. Avoid placing other heat sources nearby.
  • Do not operate the unit and disconnect the power supply cable immediately in the following cases:
    • a. The device or the mains cable has visible damage.
    • b. After a fall of the device or similar accident, if you have any doubt about its condition.
    • c. Malfunctions appear.
    • d. Never unplug the unit by pulling on the power cord; first turn the power switch to OFF, then remove the power cord by gently pulling the plug.
    • e. Use a soft and dry cloth for cleaning. Do not use chemicals or water under any circumstances.
    • f. We decline all responsibility in the event of bodily injury or material damage resulting from use for a purpose other those that for which the device is designed or if it is not correctly connected, used or repaired by an unauthorized person. Furthermore, the warranty would become null and void.

When the device is finally out of order, you must take it to a nearby recycling plant to contribute to its non-polluting disposal.

Package content

Please verify that you have all of the items listed below when you receive the product. Please contact us if any of these items are missing or damaged in transit.

1x Audiophonics DA-S250NC amplifier
1x Remote control
1x Antenna
1x Power cable
1x User manual

Keep this manual in a safe place for future reference.
Note: The illustrations in the user manual may differ slightly from the delivered product.

Warranty

Your Audiophonics DA-S250NC amplifier is warranted for two years beginning at the date of delivery. If your unit requires service, you must return it to us in its original packaging, along with the purchase receipt. The warranty covers manufacturing defects to the exclusion of any other damage, such as:

  • An accident.
  • Negligence.
  • A handling mistake.
  • Installation is not in accordance with this user manual.
  • The intervention was carried out by unauthorized persons.
  • Damage during transport (this damage will only be taken into account by the carrier if the usual legal reservations have been made with the carrier upon delivery).

Product Overview

Front panelAUDIOPHONICS-DA-S250NC-Class-D-Integrated-Amplifier-FIG-1
\(1\)

# Description
1 ON/OFF button
2 Input selection button
3 IR receiver
4 Screen
5 Volume button

Rear panelAUDIOPHONICS-DA-S250NC-Class-D-Integrated-Amplifier-FIG-1
\(2\)

# Description
6 Pre‑out
7 Coaxial input
8 Optical input
9 USB Input
10 Bluetooth antenna
# Description
--- ---
11 Right channel speaker output
12 Left channel speaker output
13 Power input
14 Power button

Remote control

AUDIOPHONICS-DA-S250NC-Class-D-Integrated-Amplifier-FIG-1
\(3\)

# Description
15 ON/OFF button
16 Input selection button
17 Menu button
18 Up navigation
19 Validation button
20 NA
21 NA
22 Bottom navigation
23 NA
24 Volume –
25 Volume +
26 Mute button

Operation of the device

  • Switching on the device
    First, connect the amplifier’s power supply connector (13) to a power outlet using the supplied power cable. Press the power button (14). The LED on the ON/OFF button (1) will light up red. Press the ON/OFF button (1) on the unit or the ON/OFF button (15) on the remote control. The amplifier is now switched on.

  • Volume control
    The DA-250NC’s volume attenuation can be adjusted over a range of -60dB to 0dB in 0.5dB steps. To increase the volume, turn the volume knob (5) clockwise or press the Volume + button (25) on the remote control. To decrease the volume, turn the volume knob (5) counterclockwise or press the Volume – button (24) on the remote control. The display (4) shows the current volume level.

  • Enable / Disable the mute mode
    The mute mode allows you to instantly mute the audio output. To enable the mute mode, press the Mute button (26) on the remote control. « MUTE » appears on the display (4). To disable the mute mode, press the Mute button (26) on the remote control again, or change the volume level using the volume control (5).

  • Input selection
    To select an input, press the Input button on the device (2) or the Input button on the remote control (16). The inputs change in the following cycle: USB > Coaxial > Optical > Bluetooth > USB. The display (4) shows the active input.

Settings

To enter the unit’s configuration screen, press the Select button (17) on the remote control. Five settings appear on the screen (4). Use the Up (18) and Down (22) navigation buttons on the remote control to select a setting. Press the Enter Button (19) on the remote control to enter the selected setting.

  1. Max output level
    This parameter allows to change the gain attenuation level of the amplifier and the DAC. The following settings are available :

  2. 0dB (default)

  3. -6dB

  4. -12dB

  5. -18dB

  *  **Note:** The volume display on the screen does not reflect the use of this setting.
  *  **Example:** If you select a gain attenuation level of -6dB and set the volume level to -30dB on the display, then the actual attenuation level is -36 dB.
  1. PCM filter
    This parameter allows you to select a digital PCM filter to adjust the sound of the device. Four filters are available:

  2. Apodizing Fast (default)

  3. Fast linear

  4. Slow linear

  5. Fast minimumAUDIOPHONICS-DA-S250NC-Class-D-Integrated-Amplifier-FIG-1 \(4\)

  6. 2nd harmonic
    This parameter allows you to adjust the gain level of the second harmonic, which can in some cases offer a more musical sound reproduction. Four gain levels are available:

  7. Normal (default)

  8. +3dB

  9. +6dB

  10. +12dB

  11. DPLL bandwidth
    The DPLL bandwidth setting adjusts the locking frequency of the signal. For best performance, the DPLL bandwidth should be set to the minimum. Four settings are available:

  12. Normal (default)

  13. Faible

  14. Très faible

  15. Minimum

  16. Input name
    This setting allows you to change the displayed name of the WiFi input (not available on this model). Four settings are available :

  17. IIS

  18. WIFI

  19. Stream

  20. OFF (default)

  *  **Note:** On this model, the WiFi input is not available. The display of the name of the input is therefore disabled by setting 4. OFF.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals