MAXI-COSI Emme 360 All in Convertible Car Seat User Manual
- June 13, 2024
- MAXI-COSI
Table of Contents
- Getting Started
- Rear-Facing Section
- Forward-Facing Section
- Securing Child in Car Seat
- Booster Seat Section
- Storing Harness System
- Booster Seat Use in Vehicle
- Changing Headrest/ Harness Height
- Changing Buckle Position
- Removing Seat Pad Set
- Cleaning Parts of Car Seat & Installing Seat Pad Set
- Vehicle Belts
- Replacement & Expiration
- Registration & Safety Notices
- Aircraft Information
- Warranty
- Documents / Resources
Emme 360TM
All-in-One Convertible Car Seat
Your model may look different than one shown on cover.
Read all instructions BEFORE USING this car seat.
KEEP INSTRUCTIONS FOR FUTURE USE.
Failure to follow the warnings on the labels and in the instruction manual can result in serious injury or death to your child.
Getting Started
Welcome to the Maxi-Cosi Family!
Thank you for choosing this car seat, also known as a child restraint!
To help you get started using your child’s new car seat, here are the 4 main
tasks you’ll need to complete.
Your child’s safety is worth the time it will take to read and follow these
instructions.
Ready? Let’s go!
Pages 1-4 will introduce you to the parts of the car seat.
The Back Cover of this Manual has our contact information.
If at any point you would like assistance, please feel free to reach out to
us.
Parts of Car Seat
Accessory Use
Head Pillow
(on select models)
Only For Use in Rear-Facing Mode
To remove head pillow, from the back of the head pillow gently pull the
fabric tabs out of from around the harness straps.
Wedge Pillow
(on select models)
Only For Use in Rear-Facing Mode
To remove wedge pillow, undo the buckle and pull it through the slot in the
pillow. Slide the pillow out from behind the harness straps.
Body Pillow
(on select models)
MUST Use in Rear-Facing Mode and Forward-Facing Mode up to 30 lbs
To remove body pillow, slide the pillow out from behind the harness straps.
Toddler Pad
(on select models)
For Use in Rear-Facing Mode or Forward-Facing Mode up to 40 lbs
To remove toddler pillow, undo the buckle and fasteners on pad.
Then pull it through the slot in the pillow.
Removable Cup Holder(s)
(on select models)
For Use in All Modes
The cup holder(s) is top rack dishwasher safe.
To remove cup holder, twist the cup holder counterclockwise. Pull it out of
the slot in the car seat.
For a larger cup, twist the cup holder insert counterclockwise as shown.
Buckle Cover
(on select models)
For Use in Rear-Facing Mode or Forward-Facing Mode
To remove, undo the buckle and pull the buckle cover off the buckle.
Harness Covers
(on select models)
For Use in All Modes
The harness covers help provide comfort to your child’s neck.
To remove, undo the harness pull the fastening strips apart and pull the
harness covers off of the top part of harness cover. The bottom part is not
removeable.
Installing Base with Vehicle Belt
WARNING:
DO NOT use both the LATCH: lower anchor belt and vehicle belt at the same
time to install the car seat.
When anchors are available, you MUST ALWAYS attach, adjust, and secure the
tether (top anchorage) strap when installing the car seat.
Before installing the car seat in your vehicle, check to see if needed to
adjust the buckle position for your child.
See page 21 for Rear-Facing buckle positions.
See page 28 for Forward-Facing buckle positions.
Once the car seat is installed, you will not be able to adjust the buckle
position.
Review Vehicle Owner’s Manual
Determine what kind of vehicle belts your car has and how to use them to lock
a car seat in place OR where LATCH: lower anchor seating positions are located
in your vehicle.
-
Place Base in Vehicle Seat
Squeeze the rotate handle and swivel the seat to face you in side view.
Squeeze the release handle located on the front of the car seat while lifting the car seat off the base and flipping it over to the opposite side. -
Lay Top Tether Strap Over the Vehicle Seat
You will be installing the top tether strap in steps 7 & 8.
Review the vehicle owner’s manual for the tether anchor locations. For LATCH Belt, go to page 9 to bypass the lock off.
For Lap Belt only, Skip Step 3 and leave lock off closed. -
Open Belt Lock Off
Squeeze the lever to open the belt lock off & pull it forward. -
Weave Vehicle Seat Belt In and Out of Belt Path As Shown
Buckle the vehicle belt. -
Tighten Belt & Gently Remove Slack
Place your hand in the base and firmly push the base down and back toward the vehicle seat. Pull the belt parallel (in line) with the belt path as shown. -
Close Belt Lock Off Both indicators will turn completely green when vehicle belt is properly installed. If your car has a vehicle belt that can switch to locking mode, you use it to lock the belt.
Switching vehicle belt to locking mode: Slowly pull the shoulder belt all the way out, then let it go back in 1-2 in. (2.5-5 cm).
As it goes back in, you will most likely hear a ratcheting sound.
Gently pull the belt to see if it has locked. You will not be able to pull any more belt out if the lock has engaged.
-
Locate Vehicle Tether Anchors
Locations vary by vehicle.
Review your vehicle owner’s manual for top tether anchor locations and how to route the belt when there are vehicle headrests.
Attach and Tighten Top -
Tether Strap Until Tether Door Is Flush With Base As Shown
If the base moves more than 1 in. (2.5 cm), you can try:
- Pulling the belt tighter; OR
- Reinstalling the base; OR
- Changing to a different seating location; OR
- Switching to a different install method (LATCH: Lower Anchor Belt).
FINISHED!
-
Tether Installed? If it is not installed, see steps 7 & 8.
-
Belt Tension Indicators Completely Green?
If they are not green, see steps 3-6. -
Car Seat Cradle Side-Facing As Shown? If it is not side-facing, squeeze the rotation handle and it move into side-facing position.
Rear-Facing Car Seat into Base Install: pages 19-23. Forward-Facing Car Seat into Base Install: pages 27-29.
Booster Seat into Base Install: pages 42-45.
Flip Car Seat Over
Push down on the front of the car seat to lock into place.
Installing Base with LATCH: Lower Anchor Belt
WARNING:
DO NOT use both the LATCH: lower anchor belt and vehicle belt at the same time
to install the car seat.
When anchors are available, you MUST ALWAYS attach, adjust, and secure the
tether (top anchorage) strap when installing the car seat.
Before installing the car seat in your vehicle, check to see if you need to
adjust the buckle position for your child.
See page 21 for Rear-Facing buckle positions.
See page 28 for Forward-Facing buckle positions.
Once the car seat is installed, you will not be able to adjust the buckle
position.
Review Vehicle Owner’s Manual
Determine what kind of vehicle belts your car has and how to use them to lock
a car seat in place OR where LATCH: lower anchor seating positions are located
in your vehicle.
-
Place Base in Vehicle Seat
-
Lay Top Tether Strap Over the Vehicle Seat
You will be installing the top tether strap in steps 6 & 7.
Review the vehicle owner’s manual for the tether anchor locations. -
Take Lower Anchor Belt Out of Storage Location
Vehicle Belt Lock Off MUST BE Closed BEFORE Routing Lower Anchor Belt -
Weave Lower Anchor Belt In & Out of Belt Path
Then attach lower anchor hooks to the vehicle’s lower anchor. -
Tighten Belt & Gently Remove Slack
Place your hand in the base and firmly push the base down and back toward the vehicle seat.
Pull the belt parallel (in line) with the belt path as shown.
Tension indicators will begin to turn green.
Both indicators will turn completely green when the LATCH is properly installed.
If the base moves more than 1 in. (2.5 cm),
you can try:
• Pulling the belt tighter; OR
• Reinstalling the base; OR
• Changing to a different seating location; OR
• Switching to a different install method (vehicle belt). -
Locate Vehicle Tether Anchors
Locations vary by vehicle.
Review your vehicle owner’s manual for top tether anchor locations and how to route the belt when there are vehicle headrests. -
Attach and Tighten Top Tether Strap Until Tether Door Is Flush With Base As Shown
FINISHED!
-
Tether Installed? If it is not installed, see steps 6 & 7.
-
Belt Tension Indicators Completely Green?
If they are not green, see steps 4 & 5. -
Car Seat Cradle Side-Facing As Shown? If it is not side-facing, squeeze the rotation handle and it move into side-facing position.
Rear-Facing Car Seat into Base Install: pages 19-23.
Forward-Facing Car Seat into Base Install: pages 27-29.
Booster Seat into Base Install: pages 42-45.
Flip Car Seat Over
Push down on the front of the car seat to lock into place.
Choosing Car Seat Mode
WARNING:
Measure your child’s weight and height
(DO NOT guess) before choosing this car seat’s mode.
Your child’s height, weight, and age determine how the car seat should be
placed in the vehicle.
Children vary widely in body size, shape, and temperament—please consult your
doctor before switching between any modes within the limits and fit
requirements of the car seat.
State Laws
Please be certain to follow your state’s laws regarding car seat use.
American Academy of Pediatrics Recommendations
Infants and Toddlers
Should ride in a rear-facing car seat as long as possible, until they reach
the highest weight or height allowed by their car seat.
Toddlers and Preschoolers
Once they are facing forward, children should use a forward-facing car seat
with a harness for as long as possible, until they reach the height and weight
limits for their car seats.
School-Aged Children
Once they have outgrown their forward-facing car seat, children should use a
belt-positioning booster seat until the vehicle’s lap and shoulder seat belt
fits properly. This is often when they have reached at least 4 feet 9 inches
in height and are 8 to 12 years old.
Older Children
All children younger than 13 years should be restrained in the rear seats of
vehicles for optimal protection.
Rear-Facing Mode
5-40 lb (2.3-18 kg) and
19-40 in. (48-101.6 cm)
Rear-Facing Section
PAGE 17
Rear-Facing Child Fit &
Vehicle Install
PAGE 19
Forward-Facing Mode
22-65 lb (10.1-29 kg) and 29-49 in. (73.6-125 cm) and at least 1 year old
Forward-Facing Section
PAGE 24
Forward-Facing Child Fit &
Vehicle Install
PAGE 26
Booster Seat Mode
40-100 lb (18.1-45.4 kg) and 43-52 in. (110.1-132.1 cm)
Booster Seat Section
PAGE 35
Storing Harness System
PAGE 37
Booster Seat Use in Vehicle
PAGE 42
Rotating & Reclining Car Seat on Base
You must squeeze the Rotation Handle on the front of the base to move the seat
out of Rear-Facing or Forward-Facing modes.
Rotation Lock Indicator will show the locked symbol when car seat is locked in
place.
WARNING:
SIDE-FACING Position ONLY for use when:
- child into car seat.
- Removing child from car seat.
Side-Facing Position (Towards Parent)
To rotate the car seat from Side-Facing for all modes, firmly rotate the seat
towards the back or front of the base.
Rear-Facing Mode
Rotation Lock Indicator will show the locked symbol when car seat is locked in place.
Forward-Facing and Booster Seat Mode
The car seat must be fully reclined BEFORE rotating it to Forward Facing.
Reclining Car Seat
There are 5 Recline positions in Rear-Facing Mode.
To Recline: Squeeze the recline handle
and push the top of the car seat back.
For More Upright: Squeeze the recline handle and pull the top of the car
seat forward.
Rear-Facing Section
Children under 1 year of age MUST ride Rear-
Facing.
In this car seat, your child can remain Rear-Facing until they outgrow any one
of the following:
- Weight Limit: 40 lb (18 kg); OR
- Height Limit: 40 in. (101.6 cm); OR
- Rear-Facing Child Fit requirements, see pages 19-23.
Before installing the car seat in your vehicle, check your child’s fit in the
car seat.
This way you won’t have to redo the vehicle installation to make adjustments
to the car seat.
Rear-Facing Child Fit & Vehicle Install: Page 19
WARNING:
NEVER install a rear-facing child restraint in the front seat of a vehicle
equipped with an active frontal airbag.
DO NOT use the lower anchors of the child restraint anchorage system (LATCH
system) to attach this child restraint when restraining a child weighing more
than 25 lb (11 kg).
The vehicle belt MUST be used for installation if your child weighs more than
25 lb (11 kg).
DO NOT use the lower anchor belt along with the vehicle lap or lap/shoulder
belt.
DO NOT fasten multiple lower anchor hooks on the same lower anchor bar in the
vehicle.
Check the vehicle belt or the lower anchor belt before each use. Use ONLY if
the belt can be tightened properly and locked securely in place.
Even when unoccupied, this child restraint MUST be firmly secured to the
vehicle with the lower anchor belt or with the vehicle seat belt.
This child restraint MUST ALWAYS face the rear of the vehicle until the child
is at least 1 year old and weighs 22 lb (10 kg).
Do not use this chest clip with children who have an implanted electronic
medical device.
A magnet is used to help secure the chest clip locking mechanism together
which may interfere with the proper function of an implanted electronic
medical device.
Parents or caregivers who have an implanted electronic device should keep
their device away from the chest clip and consult their doctor and medical
device manufacturer for specific information before using this chest clip.
Rear-Facing Child Fit & Vehicle Install
**WARNING:**
The car seat is attached to the base via cable wires and should NOT be removed
-
Put Car Seat in Side-Facing Position on Base
Squeeze the Rotate handle and swivel the seat to face you in side view. -
Fully Loosen Harness Straps
Push down on the harness release lever (through the opening in the pad) while pulling out on the harness straps as shown. -
Undo Buckle
-
Undo Chest Clip
Hold the chest clip with both hands and press in on the top and bottom buttons with your index finger and thumb as shown.
While holding the buttons in, pull the right (top) half of the clip apart from the left (bottom) half to release the magnet and separate the chest clip. -
Place Child in Car Seat
On select models: You may use the In and Out Harness Holders to place the harness straps out of the way.
Your child’s bottom and back should be flat against the car seat.
-
Check Headrest Position
The top of your child’s head MUST be at least 1 in. (2.5 cm) below the top of the car seat’s headrest.
-
Check Harness Strap Position
The harness strap MUST be at or slightly below the shoulders; never above. -
Check Buckle Position
• Use the slot closest to your child.
• The buckle should not be underneath or behind your child.
DO NOT use the 3rd buckle slot in Rear-Facing Mode.
-
Push Car Seat Towards Back of the Base
Rotation Lock Indicator will show the locked symbol when car seat is locked in place.
Only if necessary, you may place a tightly rolled towel(s) or foam pool
noodle(s) under the front of the car seat base to help make the Rear Facing
Level Line parallel with the ground.
Check often to make sure padding is still in place and the belt is tight.
To secure child in car seat, see pages 31-34.
To change the harness strap height, see page 46.
To change the buckle position, see pages 47-48.
To learn how to check harness tightness, see pages 31-34.
FINISHED!
Headrest Position: Is your child’s headrest
in the correct position? See step 5.
Harness Strap Position: Is your child’s harness strap in the correct position?
See step 6.
Buckle Position: Is your child’s buckle in the correct position? See step 7.
Vehicle Belt Install: See page 5.
LATCH: Lower Anchor Belt Install: See Page 9.
Forward-Facing Section
22-65 lb (10.1-29 kg) and 29-49 in. (73.6-125
cm) and at least 1 year old
Children MUST be at least 1 year of age to ride Forward-Facing.
In this car seat, your child can remain harnessed
Forward-Facing until they outgrow any one of the following:
- Weight Limit: 65 lb (29 kg); OR
- Height Limit: 49 in. (125 cm); OR
- Forward-Facing Child Fit requirements, see pages 29-30.
Before installing the car seat in your vehicle, check your child’s fit in the
car seat.
This way you won’t have to redo the vehicle installation to make adjustments
to the car seat.
Forward-Facing Child Fit & Vehicle Install: Page 26
WARNING:
DO NOT use the lower anchors of the child restraint anchorage system (LATCH
system) to attach this child restraint when restraining a child weighing more
than 30 lb (14 kg).
The vehicle belt MUST be used for installation if your child weighs more than
30 lb (14 kg).
When anchors are available, you MUST ALWAYS attach, adjust, and secure the
tether (top anchorage) strap when installing the car seat in the Forward-
Facing Mode with internal harness.
DO NOT use the lower anchor belt along with the vehicle lap or lap/shoulder
belt.
Check the vehicle belt or the lower anchor belt before each use. Use ONLY if
the belt can be tightened properly and locked securely in place.
DO NOT fasten multiple lower anchor hooks on the same lower anchor bar in the
vehicle.
Even when unoccupied, this child restraint MUST be firmly secured to the
vehicle with the lower anchor belt or with the vehicle seat belt.
In this child restraint your child MUST be at least 1 year old and weigh 22 lb
(10.1 kg) before they sit forward-facing.
Do not use this chest clip with children who have an implanted electronic
medical device.
A magnet is used to help secure the chest clip locking mechanism together
which may interfere with the proper function of an implanted electronic
medical device.
Parents or caregivers who have an implanted electronic device should keep
their device away from the chest clip and consult their doctor and medical
device manufacturer for specific information before using this chest clip.
Forward-Facing Child Fit & Vehicle Install
WARNING:
The car seat is attached to the base via cable wires and should NOT be removed
-
Put Car Seat in Side-Facing Position on Base
Squeeze the Rotate handle and swivel the seat to face you in side view. -
Fully Loosen Harness Straps
Push down on the harness release lever while pulling out on the harness straps as shown.
-
Undo Buckle
-
Undo Chest Clip
Hold the chest clip with both hands and press in on the top and bottom buttons with your index finger and thumb as shown.
While holding the buttons in, pull the right (top) half of the clip apart from the left (bottom) half to release the magnet and separate the chest clip. -
Place Child in Car Seat
On select models: You may use the In and Out Harness Holders to place the harness straps out of the way.
Your child’s bottom and back should be flat against the car seat. -
Headrest Position
The tops of your child’s ears MUST be below the top of the car seat’s headrest. -
Harness Strap Position
The harness strap MUST be at or slightly above the shoulders; never below .
-
Buckle Position
• Use the slot closest to your child.
• The buckle should not be underneath or behind your child.
The buckle can be used in any buckle slot.
-
Push Car Seat towards the Back of the base
The car seat must be fully reclined to rotate it Forward-Facing.
Rotation Lock Indicator will show the locked symbol when car seat is locked in place.
To secure child in car seat, see pages 31-34.
To change the harness strap height, see page 46.
To change the buckle position, see pages 47-48.
To learn how to check harness tightness, see pages 31-34.
FINISHED!
Headrest Position: Is your child’s head in the correct position? See
step 5.
Harness Strap Position: Is your child’s harness strap in the correct
position? See step 6.
Buckle Position: Is your child’s buckle in the correct position? See
step 7.
Vehicle Belt Install: See page 5.
**** LATCH: Lower Anchor Install: See Page 9.
Securing Child in Car Seat
WARNING:
Do not use this chest clip with children who have an implanted electronic
medical device.
A magnet is used to help secure the chest clip locking mechanism together
which may interfere with the proper function of an implanted electronic
medical device.
Parents or caregivers who have an implanted electronic device should keep
their device away from the chest clip and consult their doctor and medical
device manufacturer for specific information before using this chest clip.
-
Place Child in Car Seat
Your child’s bottom and back should be flat against the car seat.
-
Buckle Harness
Pull the harness straps up to make sure the buckle is locked. -
Fasten Chest Clip click
Lay the right (top) half of the chest clip over the left (bottom) half and it will automatically snap together and lock.
Pull gently on each half of the chest clip together to make sure it is locked. -
Tighten Harness
Pull the harness adjustment strap straight out to snugly tighten the harness .
-
Position Chest Clip
Pull the harness covers down on the child.
Place the chest clip on the lower part on the harness cover so that the harness covers are between your child and the chest clip.
Position it at mid-chest (even with armpits) and away from your child’s neck .
-
Check Harness Tightness
Unfasten the harness covers.
Try to pinch the harness at the shoulders vertically between index finger and thumb as shown.
If your fingers slip off, the harness is tight
enough.
If you can pinch the harness strap, tighten more.
Fasten the harness covers.
A snug strap should not allow any slack.
It lies in a relatively straight line without sagging.
It does not press on the child’s flesh or push the child’s body into an
unnatural position.
FINISHED!
Your child is now secured in the car seat.
Check your child’s fit often and make any needed adjustments to the car seat
as they grow.
To Remove Child from Car Seat:
- Loosen Harness Strap
- Unbuckle Harness
- Release Chest Clip
- Remove Child
Troubleshooting
-
If the buckle or harness release lever sticks: DO NOT lubricate. Check for dropped food, sticky spilled drinks, dirt, leaves, etc.
Clean with warm water and/ or remove the object with tweezers. If you cannot get the harness to adjust and remain tight with the buckle securely locked, DO NOT use this car seat. -
If your harness twists: Straighten the harness each time you put your child in the car seat. Lock the buckle and tighten the harness so it will be ready for next use.
WARNING:
Failure to fasten and tighten the harness system correctly may allow the
child to be ejected from the child restraint in a crash or sudden stop causing
serious injury or death.
DO NOT mistake comfort for safety. The harness system MUST be snugly adjusted.
DO NOT put snowsuits or bulky garments on your child when placing them in the
child restraint.
Bulky clothing can prevent the harness straps from being tightened properly.
Booster Seat Section
40-100 lb (18.1-45.4 kg) and
43-52 in. (110.1-132.1 cm)
In this car seat, your child can remain in a Booster Seat until they outgrow
any one of the following:
- Weight Limit: 100 lb (45.4 kg); OR
- Height Limit: 52 in. (132.1 cm); OR
- Booster Seat Use in Vehicle requirements, see page 42-45.
You MUST store the harness system and remove the accessories, except the cup
holder(s), when using the Booster Seat Mode.
To remove accessories, see pages 3-4.
Storing Harness System: Page 37
Booster Seat Use in Vehicle: Page 41
WARNING:
DO NOT use the harness system when using as a booster seat.
Use ONLY the vehicle’s lap and shoulder belt
system when restraining the child in this booster seat.
DO NOT use only the lap belt when using this seat as a booster seat.
The shoulder belt MUST always be adjusted snugly across the child’s chest.
NEVER place shoulder belt under the child’s arms or behind their back.
DO NOT use the lower anchor belt along with the vehicle lap or lap/shoulder
belt.
DO NOT use this booster seat if the tops of your child’s ears are above the
top of the booster seat’s headrest.
This restraint is NOT certified for
aircraft use when used as a booster seat because aircraft seats do not have
shoulder belts.
Storing Harness System
-
Fully Loosen Harness Straps
-
Undo Buckle
-
Remove Cup Holders
Twist the cup holder counterclockwise.
Pull it out of the slot in the car seat. -
Lift Seat Pad from Front of Car Seat
-
Pull Buckle & Buckle Cover Out of Car Seat
Store the buckle and buckle cover in a safe place for future use. -
Adjust Headrest to Highest Position
-
Undo Fasteners on Headrest Pad & Seat Pad
-
Pull Headrest Pad Off Top of Headrest
-
Thread Harness Straps into Slots on Sides of Headrest
Place the chest clip, the harness straps, & the buckle tongues behind the bottom of headrest
-
Tighten Harness
Remove any slack from the harness system.
-
Wrap Headrest Pad Around Top of Headrest
Attach the fasteners on the headrest pad and the seat pad. -
Replace Cupholders
Put it in of the slot in the car seat.
Twist the cup holder clockwise.
FINISHED!
The car seat has been converted to the Booster Seat Mode.
See next page for Booster Seat Use in Vehicle.
Booster Seat Use in Vehicle
WARNING:
The car seat is attached to the base via cable wires and should NOT be removed
-
Put Booster Seat in Side-Facing Position on Base
Squeeze the Rotate handle and swivel the seat to face you in side view.
-
Have Child Sit in Booster Seat
The tops of your child’s ears should never be above the top of the booster seat’s headrest.
**** If your vehicle has a headrest that
interferes with a flush car seat fit, check your vehicle owner’s manual to see
if it can be removed, adjusted, or if there are other possible seating
locations for you to install. -
Car Position
DO NOT use the booster seat if your child’s head is less than 5 in. (12.7 cm) below the roof of the car. Consult your vehicle manual for proper seat belt usage. -
Shoulder Belt Position
The shoulder belt should lay snugly across the center of your child’s shoulder and across their chest.
-
Position Lap Belt on Child
Route ONLY the lap belt portion of the vehicle belt through the Booster Seat Belt Path as shown. The lap belt should lay snugly across your child’s hips; not on their stomach. -
Buckle Vehicle Belt Pull the shoulder belt up to tighten.
-
Position Shoulder Belt on Child
Thread the shoulder belt through the belt- positioning guide in the headrest.
Pull the shoulder belt up to tighten so that it lies snugly across the center of your child’s shoulder and across their chest.
FINISHED!
Check periodically to make sure your child has not moved out of position and loosened the shoulder belt.
Keep the booster seat securely belted through the belt-positioning guider even when unoccupied.
Changing Headrest/ Harness Height
-
Fully Loosen Harness Straps
Push down on the harness release lever (through the opening in the pad) while pulling out on the harness straps as shown. -
Adjust Headrest/ Harness Height
1. Squeeze the adjustment handle lever up.
2. Move the headrest up or down to the proper height for your child.
3. Release the handle to lock in place.
4. Make sure it is locked securely.
**** For Rear-Facing Child Fit, see page 19-21.
For Forward-Facing Child Fit, see page 27-28.
To learn how to check harness tightness, see pages 31-34.
Check the harness straps often for any wear or damage.
Changing Buckle Position
WARNING:
Failure to place buckle’s metal retainer completely through pad and child
restraint can result in serious injury or death.
-
Undo Buckle
-
Remove Cup Holders Twist the cup holder counterclockwise.
Pull it out of the slot in the car seat.
-
Lift up Seat Pad
-
Push Buckle Strap Down & Pull One Side of Buckle Strap to Center
Place buckle strap into desired buckle slot. Push the other side of buckle strap into the buckle slot. -
Replace Seat Pad Around Bottom & Sides of Seat
-
Replace Buckle Cover and Check Buckle
Pull the buckle up to make sure it is secured.
The buckle MUST NOT pull out.
**** For Rear-Facing Child Fit, see page 19-21.
For Forward-Facing Child Fit, see page 27-28.
To learn how to check harness tightness, see pages 31-34.
Removing Seat Pad Set
**** You do not need to remove the harness system to remove the pad from the
car seat.
DO NOT fully pull the harness strap out of the car seat. Leave it threaded in
the hip harness slots. If removed, you will not be able to rethread it.
To remove accessories, see pages 3-4.
-
Adjust Headrest to Highest Position
-
On Select Models:
Undo Fasteners on Headrest Pad -
Gently Pull
Headrest Pad Off Top of Headrest
-
Undo Fastners on Seat Pad
-
Remove the Cup Holders
Twist the cup holder counterclockwise.
Pull it out of the slot in the car seat. -
Pull Seat Pad Off Sides & Bottom of Car Seat
-
Lower Headrest to Middle of Car Seat
-
Pull Seat Pad Around Headrest & Off of Car Seat
Cleaning Parts of Car Seat & Installing Seat Pad Set
Cleaning Pad & Top Harness Cover & Accessories
Top harness cover ONLY can be machine washed. MUST turn car seat pad inside-
out before machine washing. Machine wash separately with cold water on a
gentle cycle. DO NOT use bleach.
Tumble dry separately for 10-12 minutes on low heat. Remove immediately.
Toddler Pad: Place inside pillow case. DO NOT use bleach. Tumble dry
separately for 10-12 minutes on low heat. Remove immediately.
Wedge Pillow & Body Pillow: Remove wedge from pocket on the back of pillow
before you machine wash.
Cleaning Harness Strap & Bottom Harness Cover Check the harness straps often
for any wear or damage.
Spot clean using warm sudsy water and damp cloth. Spilled food and liquids on
the car seat may result in mold or bacterial growth over time. These spills
could also attract insects or rodents.
Cleaning Buckle & Car Seat
Spot clean using warm sudsy water and damp cloth. DO NOT submerge into water.
Installing Seat Pad Set
- Lower Headrest to Middle of Car Seat
- Pull Seat Pad Around Headrest
- Pull Seat Pad around Sides & Front of Car Seat
- Adjust Headrest to Highest Position
- Pull Headrest Pad onto Headrest
- On Select Models: Attach All Pad Fasteners
- Replace Cup Holders
WARNING:
DO NOT fully pull the harness strap out of the car seat.
Leave it threaded in the hip harness slots. If removed, you will not be able
to rethread it.
DO NOT use the child restraint without the seat pad or with damaged harness
straps.
LATCH: Lower Anchor Belt
The lower anchors of LATCH (Lower Anchors and Tethers for Children’s) is a universal system for installing car seats without using vehicle seat belts. The LATCH: lower anchor belt can ONLY be used in vehicles that have the lower anchor bars installed in designated seating positions. Most vehicles manufactured after September 2002 are equipped with LATCH: lower anchor bars. Check your vehicle owner’s manual to see which seating positions may be equipped with LATCH: lower anchor bars.
To Remove Lower Anchor Belt from Storage Location in Base
Pull LATCH: Lower Anchor Belt out of storage location in base.
To Remove Lower Anchor Belt from Vehicle’s Lower Anchor Bars
- Remove the tension from the belt by pushing down on the side of the base with the adjuster.
- Press the adjuster’s button to loosen the belt.
- Squeeze the spring lever on the hooks, push the hooks back into the vehicle seat, and rotate the hooks to the side.
- Pull the hooks off of the vehicle’s lower anchor bars.
To Store Lower Anchor Belt
The lower anchor belt MUST be properly stored in its storage location when:
- using the vehicle belts to install the base; OR
- the base is not installed in a vehicle.
Gather the lower anchor belt and place it into the storage location as shown.
WARNING:
DO NOT use both the lower anchor belt and vehicle belt at the same time.
Vehicle Belts
Your vehicle’s features may be considerably different than those pictured
here.
If LATCH: lower anchors are not an option or if your child weighs more than 25
lb (11 kg), in Rear-Facing Mode or 30 lb (14 kg) in Forward-Facing Mode you
MUST use the vehicle seat belt system to install the car seat.
Not all vehicle belts and seating positions will work with car seats. Please
go through the following steps to understand how to lock a car seat in Rear-
Facing Mode or Forward-Facing Mode with a vehicle belt.
-
You MUST Review Your Vehicle Owner’s Manual
Your vehicle owner’s manual will let you know which vehicle belts and seating positions car seats can be installed in.
-
Check How This Car Seat Will Be Locked Into Place
The vehicle belt MUST NOT loosen after tightening.
This means there needs to be a way to lock the vehicle belt.
The ways this can be done are:
• By using the seat belt’s retractor (see step 3); OR
• By using the seat belt’s latch plate (see step 4).
Lock Off
When used correctly, this base’s Lock Off will lock the vehicle belt.
Please go to the vehicle belt with base installation section of the manual to see how to properly use this feature.
Base Install with Vehicle Belt: Page 5
-
Check Retractor
Retractors pull seat belts into stored positions and lock the belt to hold passengers in place.
See the next page for some common types of vehicle belt retractors that will work with this car seat.
Types of Retractors Switchable Retractor (most vehicles have this type)
This retractor can be switched to a locking mode.
You MUST have the retractor in the locking mode to use the seat belt with this
car seat.
Switching to locking mode: Slowly pull the shoulder belt all the way out, then
let it go back in 1-2 in. (2.5-5 cm).
As it goes back in, you will most likely hear a ratcheting sound.
Gently pull the belt to see if it has locked. You will not be able to pull any
more belt out if the lock has engaged.
Automatic Locking Retractor
This retractor always locks.
It will automatically lock after slowly pulling the seat belt out at least
halfway and letting the belt go back into the retractor 1-2 in. (2.5-5 cm).
Emergency Locking Retractor See Step 5 “Check Latch Plates”
If the retractor does not lock, it is most likely an Emergency Locking
Retractor. These retractors only lock during a sudden stop or collision.
You will need to determine if your seat belt’s latch plate can lock the belt.
See step 5, “Check Latch Plates”.
Check Latch Plates
Latch plates are the part of the seat belt that goes into the buckle.
To see if the latch plate locks:
- Buckle Vehicle Belt
- Firmly Tug Lap Portion of Seat Belt While Pulling It Up
If the vehicle belt does not slide through the latch plate, it’s locked.
If the latch plate slides up and down the vehicle belt, it is a sliding latch
plate.
Sliding latch plates easily slip between the lap and shoulder portions of the
belt.
Never Use the Following With This Car Seat:
- Emergency Locking Retractor Lap Only Belt
- Inflatable Seat Belts
Top Tether
When anchors are available, you MUST always attach, adjust, and secure the
tether (top anchorage) strap when installing the car seat.
Tethers improve the installation and stability of car seats and reduce the
risk of injury. Attach the tether hook to the tether anchor designated by your
vehicle manufacturer for that seating position. Check your vehicle owner’s
manual for more information. If the seating position does not have a tether
anchor, use a different seating position or see your dealer or a qualified
mechanic and have one installed.
WARNING:
Using this child restraint without the tether strap anchored as required by
the manufacturer would be a misuse of the child restraint and, in a sudden
stop or crash, could result in serious injury or death.
DO NOT fasten multiple tether hooks on the same tether anchor in the vehicle.
Child Restraint Use
WARNING:
NEVER take your child out of the child restraint while the vehicle is moving.
NEVER leave your child unattended. Placing your child in a hot child restraint
may result in burns.
DO NOT use a child restraint with damaged or missing parts.
DO NOT use a child restraint with cut, frayed, or damaged harnesses.
DO NOT substitute parts or try to modify the child restraint in any way. DO
NOT lubricate buckles and fasteners.
DO NOT use any child restraint accessory except those approved by Dorel
Juvenile Group.
NEVER allow any child to play with this child restraint; it is not a toy.
DO NOT remove or cover up any of the warning labels or other labels on the
child restraint.
This child restraint has been certified for use in passenger vehicles. DO NOT
use in a boat, on a motorcycle or in a cargo van or bus where there are no
seat belts or tether anchors.
Read all instructions for additional warnings.
Vehicle Seating Position
WARNING:
NEVER place a child rear-facing in a seating position with an active frontal
air bag.
Check the vehicle owner’s manual for more information about air bag/child
restraint use.
Use the child restraint only on vehicle seats that face forward.
DO NOT use on seats that face the sides or rear of the vehicle.
For vehicles without a back seat, refer to your vehicle owner’s manual.
According to accident statistics, children in rear seating positions are
statistically safer, whether you have air bags, advanced air bags, or no air
bags at all.
If you are not sure where to place the car seat in your vehicle:
- Consult your vehicle owner’s manual; OR
- Contact Dorel Juvenile Group Consumer Care Department; OR
- Visit your local Child Passenger Inspection Station. Go to https://www.nhtsa.gov/equipment/car-seats-and-boosterseats to find your closest station.
Installation in Vehicle
To avoid your child being seriously burned, take the following precautions:
- Park in the shade or where the sun does not directly hit the car seat.
- Cover the car seat with a sheet or blanket when not in use.
- Check for hot seat and buckles before placing child in car seat.
WARNING:
To help protect your vehicle seat’s upholstery from damage: you may use an
accessory approved by Dorel Juvenile Group or a single layer towel underneath
and behind car seat.
Check the vehicle belt or lower anchor belt before each use. Use only if the
belt can be tightened properly and locked securely in place.
Even when unoccupied, this child restraint MUST be firmly secured to the
vehicle with the lower anchor belt or with the vehicle seat belt.
Even when unoccupied, this booster seat MUST be firmly secured to the vehicle
with the vehicle seat belt.
In a crash or sudden stop, an unsecured child restraint or booster seat could
injure occupants.
Replacement & Expiration
DO NOT risk your child’s safety.
To keep your child as safe as possible, Dorel Juvenile Group strongly
recommends replacing the car seat even after a minor crash, even if it was not
occupied at the time.
Replacement After a Minor Crash
The National Highway Traffic Safety Administration states that for a crash to
be considered minor ALL of the following MUST be true:
- Vehicle able to drive away from the crash site; AND
- Vehicle door nearest the car seat was not damaged; AND
- No passengers were injured; AND
- Airbags did not deploy; AND
- There is no visible damage to the car seat.
If the crash your car seat was involved in meets ALL the criteria, you may not
need to replace the car seat.
If one or more of these criteria are not true or if you are uncertain of any
of your answers, replace the car seat immediately.
Replacement After a Moderate to Severe Crash
You MUST replace this car seat if it has been in a moderate to severe car
crash.
This car seat is intended to protect a child in a single crash.
During a crash, the car seat and all of its parts absorb crash energy which
can deform or weaken it. Damage is not always visible. A damaged car seat MUST
be replaced immediately. Brand Car Seat 05/16/2015
Expiration
On the bottom of the car seat there is a date of manufacture label as shown.
DO NOT use this car seat more than 10 years after the date of manufacture.
Registration & Safety Notices
Example of model number, manufacture date, and line code.
If you don’t have the card or if your address changes, you will find the model
number, manufacture date, and line code on the label located on the bottom of
the car seat.
Please complete the postage-paid registration card that came with your child
restraint, and send it to us.
Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a recall.
Send your name, address, e-mail address if available and the restraint’s model
number and manufacturing date to:
Dorel Juvenile Group
2525 State Street
Columbus, IN 47201 or call
1-800-951-4113 or register online at
www.djgusa.com/registration/carseat/us.
For recall information, call the U.S. Government’s Vehicle
Safety Hotline at 1-888-327-4236 (TTY:
1-800-424-9153), or go to
www.NHTSA.gov.
Aircraft Information
This restraint is not certified for aircraft
use.
This restraint is NOT certified for aircraft use when used as a booster seat
because aircraft seats do not have shoulder belts.
Warranty
Dorel Juvenile Group, Inc. (DJG) warrants this product to the original retail
purchaser as follows: This product is warranted against defective materials or
workmanship for one year from the date of original purchase. An original
receipt is required to validate your warranty.
DJG will, at its option, provide replacement parts or replace this product.
DJG reserves the right to substitute if the part or model has been
discontinued.
To make a claim under this warranty contact our Consumer Care Department by
phone at 1-800-951-4113; or text us at
1-812-6522525. Our hours of operation are from 8:00 a.m. to 6:00 p.m. ET
Monday through
Thursday and from 8:00 a.m. to 4:30 p.m. on Friday.
Proof of purchase is required and shipping charges are the responsibility of
the consumer.
Warranty Limitations: This warranty does not include damages which arise
from misuse or abuse of this product.
Limitation of Damages: The warranty and remedies as set forth are exclusive
and in lieu of all others, oral or written, expressed or implied.
In no event will DJG or the dealer selling this product be liable to you for
any damages, including incidental or consequential damages, arising out of the
use or inability to use this product.
Limitation of warranties and other warranty terms and state law rights: Any
implied warranties, including implied warranties of the merchantability and
fitness for a particular purpose, shall be limited to the duration and terms
of the express written warranty. Some states do not allow limitations as to
how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above limitations may not apply to
you.
This warranty gives you specific legal rights, and you may have other rights,
which vary from state to state. Neither DJG nor the dealer selling this
product authorized any person to create for it any other warranty, obligation,
or liability in connection with this product.
Please note: Our product warranty only applies when purchased from an
authorized Maxi-Cosi retailer. The origin of products not purchased through
these authorized retailers is unknown and could be counterfeit.
We cannot support products from an unknown origin as we cannot verify the
handling or condition of such merchandise. We maintain a strong network of
authorized retailers to ensure you are purchasing safe and complete products.
Fulfillment by a third party does not guarantee you are purchasing from one of
these authorized retailers.
Pricing which is inconsistent with the majority of retailers is a strong
indication that the retailer is not authorized, as we have a consistent price
offering across all authorized retailers. If you are unsure of the
authorization status of a retailer you are considering purchasing from, or
have purchased from, you can check www.maxicosi.com/us-
en/
shops.aspx; or call our Consumer Care Department at 1-800-9514113; or text us
at 1-812-652-2525.
243135 Booster Seat Section
46 Making Adjustments to Car Seat
49 Wash & Care
53 LATCH & Vehicle Belt Information
60 Safety Information
65 Warranty
Documents / Resources
|
MAXI-COSI Emme 360 All in Convertible Car
Seat
[pdf] User Manual
Emme 360 All in Convertible Car Seat, Emme 360, All in Convertible Car Seat,
Convertible Car Seat, Car Seat, Seat
---|---
References
- Product Registration
- Baby Car Seats, Strollers, and Gear | Baby Essentials | Maxi Cosi
- Baby Car Seats, Strollers, and Gear | Baby Essentials | Maxi Cosi
- NHTSA | National Highway Traffic Safety Administration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>