NVIO AESS-DFM50H800L 4K Lite Dome Hybrid Camera Instruction Manual

Luna Series | AESS-DFM50H800L
AESS-DFM50H800L
4K Lite Dome Hybrid Camera

Main Features

• 1/3”CMOS SENSOR 4K Lite
• (3480×2160)
• 2.8mm Fixed lens
• Maximum IR Led distance 20m
• 4in1 AHD,HD-CVI, HD-TVI, CVBS (UTC)
• 12pcs (14µ) SMD IR LEDs
• IP65
• DC12V

Technical Specification

Camera

Lens

Video

Eelectrical

Warnings & Precautions

Dear Customer, we thank you for choosing one of our products whose correct use guarantees solutions of the highest quality and reliability over time. This manual provides instructions for using the product.

Connections

Make sure the camera is not powered before making connections.
The video cable is connected to the female bayonet BNC connector, which is then taken to the monitor or DVR in general via RG59 type coaxial cable and BNC connector. Twisted pair cables can also be used with balun converters. Check that the power supply is correct and provided for the camera model used. The use of adequate power supply units is recommended. 12Vdc / 1A or 12Vdc / 1,5A stabilized is recommended. The pin required is the standard 5.5 mm. Beware of power extension cables that are too long or have a small section, which could introduce an excessive voltage drop, especially when the IR illuminator is turned on.
The values expressed in the following table are to be considered at a temperature of 20 ° C [68 ° F].

Conductors section (AWG)| 24 AWG (0,22mm²)| 22 AWG (0,33mm²)| 20 AWG (0,52mm²)| 18 AWG (0,83mm²)
---|---|---|---|---
Resistance value (Ωm)| 0.078| 0.050| 0.030| 0.018
Voltage drop ( V/m)| 0.028| 0.018| 0.011| 0.006

As the copper conductor section increases, there is a decrease in the resistance value () / m) and therefore in the voltage drop on the cable itself. Therefore, consider carefully the length and section of the cable during the design phase. Excessive distances between the power supply and the camera could compromise the correct functioning of the camera. The acceptable standard of variation of the supply voltage is 12Vdc ± 10%
2.1 Installation
This section indicates how to install the camera on a ceiling or wall with protected cable passage.
Check the solidity of the structure on which you intend to fix the camera, mark the points with a pencil and drill the holes necessary for its fastening.

Dome type camera

Dome cameras consist of the camera unit and the fixing base which are screwed together. Before proceeding with the assembly, the fixing base must be unscrewed, separating it from the camera body. Generally, no tools are needed to unscrew the fixing base from the camera body, however, if this is tightened too deeply, you can help yourself by placing a rigid rod, such as a screwdriver, between the two lateral cable outlet slots located in the base. The fixing base, separated from the camera, is fixed to the wall or to the wall with plugs in correspondence with the cable outlet hole and the camera body is subsequently screwed onto it. Before tightening fully, correctly orient the viewing angle.

3.1 Framing adjustment
Once correctly fixed to the wall / ceiling, point it in the desired direction and lock it (it may vary from model to model) by tightening the screws with the supplied Allen key.
Fixed lens cameras (IR up to 20m) do not require focus as they are factory set for most applications.
To ensure excellent image quality even in low light conditions, all models are equipped with a Day & Night function with removal of the IR filter to automatically switch from color to B / W. In addition, all models are equipped with integrated 850nm IR LED illuminators, for adequate illumination of the area being shot. Be careful not to install the camera very close to strong light sources or in places subject to reflection of light that could compromise the correct vision of the camera.

OSD menu

Depending on the camera models. This model has a coaxial control:

1. Access the DVR menu in the appropriate coaxial configuration section (in ENVIO DVRs this setting is called “XVI control”. Press the central console button that appears on the monitor to enter the menu home page.
2. Select topic / function of interest using the scroll up / down buttons.
3. Use the left or right buttons to select the different operating modes.
4. Move to [EXIT] and press the center button to exit the setting mode, without saving the settings.
5. Navigate to [SAVE & EXIT] and press the center button to exit the setting mode, saving the settings.

For the full OSD manual visit www.enviosecurity.com Web: www.enviosecurity.com

References

• Envio Security
• Envio Security

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>