Go Rhino GR-5933130T RAM 1500 CREW CAB Instruction Manual
- June 13, 2024
- GO RHINO
Table of Contents
Go Rhino GR-5933130T RAM 1500 CREW CAB
PRODUCT SAFETY & LEGAL DISCLAIMER
- IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY.
- Review the product package and contents prior to beginning the installation. Take care when opening the packaging and removing items. If a return is needed you will want to return the product in its original packaging if possible.
- This instruction guide is provided as a GENERAL installation guide, some vehicles vary dimensionally and may require additional steps.
- Test fit the product on the vehicle prior to any third party modifications and or finishing. The manufacturer and/or distributors do not accept responsibility for third party charges, labor and or third part replacement modifications. Some modifications may void the factory warranty.
- Exercise due-diligence when installing this product. The manufacturer and distributors of this product do not accept any responsibility for vehicle damage or personal injury resulting from the installation of this product. Careless installation and operation can result in serious injury or equipment damage.
- This product is for general off-road use. All liability for installation and use rests with the owner/operator.
- INSTALLER: Once installation is complete, please return this guide along with other documentation included in this product back to the consumer for future reference. The manufacturer/distributors of this product do not guarantee this particular version will be available at a later date.
INJURY HAZARD
Please complete a shop and tool inspection prior to beginning the installation.
- Always make sure you have a clean, dry and well lit work area.
- Always remove jewelry, loose fitting clothing and wear protective gloves and eye protection.
- Always use extreme caution when jacking or raising a vehicle for work. Set the emergency brake and use tire/wheel blocks and jack stands. Refer to the vehicle manufacturer hand book. Utilize the vehicle manufacturers designated lifting points.
- Always use appropriate and adequate care in lifting parts during disassembly and installation. Seek help in lifting heavy or large items into place. Utilize jacks and or lifting devices when available.
- Always insure products are secure during disassembly and installation.
- Always wear eye protection and take steps to protect any exposed skin during the installations. Drilling, cutting and grinding plastic and metal may create flying particles that can cause injury.
- Always use extreme caution when drilling, cutting and or grinding on a vehicle. Thoroughly inspect the area to be drilled, on both sides of material, prior to modification and relocate any objects that may become damaged.
- Always assemble and tighten all fasteners per the installation instructions.
- Always route electrical cables carefully. Avoid moving parts, parts that may become hot and rough or sharp edges.
- Always insulate and protect all exposed wiring and electrical connections.
MAINTENANCE AND CARE
- Always perform regular inspections and maintenance on mounts and related fasteners.
- Periodically check and tighten all fasteners.
- Stripped, fractured, or bent fasteners must be replaced.
- After washing the vehicle make sure to fully dry all surfaces.
- In areas with cold temperatures make sure to wash the product often to remove harmful materials used on road ways.
- Never use abrasive cleaners or polish compounds. Clean with a gentle soap and water. If you use wax use a non-abrasive automotive wax such as pure carnauba wax.
WARNING
Some products have been designed to work together with factory rear sensor
systems, factory forward facing sensor systems and factory air bags.
- Installation of some of these products may alter the factory sensor system performance.
- Factory sensors may read shackles or hooks protruding from the fairlead and or tow hooks.
- All sensor testing is completed by Go Rhino Products and or third party testing labs on modified vehicles.
- Sensor sensitivity, factory sensor housing, orientation, and operating conditions are all variables that will influence functionality of the sensors.
- Installation of some product may effect the factory air bag systems.
- Some products allow the use of third party products such as winches, shackles, hooks, etc. Follow the respective manufacturers operating instructions for use with our products.
- Make sure to fully understand the product, it’s intended use and operation prior to use.
- Above all… be safe!
PARTS INCLUDED IN THIS LIST
ITEM| QTY.| PART NUMBER| DESCRIPTION| | ITEM| QTY.| PART NUMBER|
DESCRIPTION
---|---|---|---|---|---|---|---|---
A| 32| AST-T944| #12×1 1/2” Rnd Head Self-drill Screw| | E| 8| AST-T78G4| 1/4”
x 1” Hex Bolt
B| 4| AST-T211G4| 1/4” x 1” Button Head Screw| | F| 32| AST-RP21G4| 1/4” Flat
Washer
C| 4| AST-T931G4| 1/4” x 3/4” SEMS Bolt| | G| 69| AST-RPR70G4| 1/4” Lock
Washer
D| 25| AST-T870G4| 1/4” x 3/4” Hex Bolt| | H| 37| AST-TU119G4| 1/4” Hex Nut
Go Rhino recommends you, the installer, read this installation instruction manual from front to back before installing the product. You may also click here to view an installation video or visit http://www.gorhino.com /Installation-Videos.
TOOLS NEEDED FOR INSTALLATION
- 5/32” Hex Bit Socket
- 7/16” Socket
- 7/16” Wrench
- Ratchet & Extension
- Drill Motor & Phillips PH3 Bit
ESTIMATED TIME FOR INSTALLATION: 1.5 Hour
If you need installation service for your new product, call the authorized distributor from whom you purchased the product or an authorized installation service company which can be found by calling toll free 1-888-427-4466
ITEM
| QTY.| PART #| DESCRIPTION| | ITEM| QTY.| PART #|
DESCRIPTION
---|---|---|---|---|---|---|---|---
1| 1| | Side Rail (Driver)| | 7| 1| | Front Foot Bracket (Pass)
2| 1| | Side Rail (Passenger)| | 8| 1| | Rear Foot Bracket
3| 1| | Front Cover| | 9| 1| | Front Clamp Bracket (Driver)
4| 8| | Crossbar| | 10| 1| | Front Clamp Bracket (Pass)
5| 1| | Center channel| | 11| 2| | Rear Clamp Bracket
6| 1| | Front Foot Bracket (Driver)| | | | |
RACK ASSEMBLY
Step-1 Lay the Ceros roof rack components on a protective surface. If necessary, use the packing materials to protect the finish on the components.
Step-2 Begin the Ceros roof rack assembly by placing the side rails alongside the crossbars. Using a drill motor and Phillips bit, install each crossbar to the side rail with (2) #12 X 1 Round Head Self-drill Screw ½” and (2) 1/4” lock washer. (Fig 1). Snug but do not tighten the screws.
Step-3 Install (2) ¼” x ¾” hex bolts in the channel that faces forward and backward of each crossbars from the 2nd to 6th. (Fig 2). Install in the 1st crossbar in the channel that faces backward (1) ¼” x ¾” hex bolt. Install in the last crossbar in the channel faces forward (1) ¼” x ¾” hex bolt. Place the center channel on the crossbars, make sure it is centered and secure it to the bolts installed in the crossbars using (1) ¼” flat washers, (1) ¼” lock washer and (1) ¼” hex nut per bolt . (Fig 3). Snug but do not tighten the bolts.
Step-4 Install (3) ¼” x 3/4” hex bolts in the channel of the front crossbar that will be facing forward when the Ceros roof rack is fully assembled. (Fig 4).
Step-5 Install (4) 1/4” x 1” hex bolt in the channel of the 2nd and 6th crossbar that will be facing down when the Ceros roof rack is fully assembled. (Fig 5). NOTE: Make sure a pair of bolts remains on each side of the roof rack, use tape to avoid the bolts moves along the rail.
Step-6 Position the front cover in place, align the holes in the front cover with the rivet-nuts in the side rails. Attach each side of the front cover to the side rail using (2) ¼” x ¾” SEMS bolts. Attach the front cover to the front crossbar bolts using (1) ¼” hex nut and ¼” lock washer, per bolt (Fig 6 & 7). Do not tighten yet.
Step-7 Adjust and align if necessary and proceed to tighten the screws and nuts, starting with the side rails screws.
RACK INSTALLATION
Step-8 Remove the roof molding from the vehicle by starting at front, carefully lift up a little bit the trim using a plastic prying tool until you pop out the molding from the clip. There are 6 clips along the roof. To release the roof molding from the last clip you need to slide it up. Carefully push the center tabs to remove the plastic clips from the retainer knob (Fig 8).
Step-9 Begin the installation on the driver side, assembly the front clamp bracket with the front foot bracket using (1) ¼” x 1” button head screw, (1) ¼” lock washer, (1) ¼” flat washer and (1) ¼” hex nut. (1-2 turn thread), (Fig 9).
Step-10 Open the front door, measure from the windshield approximately 8 1/2”, use tape to delimit. Position the front foot bracket into the rain gutter. Hook the clamp front bracket in the door frame (Fig 10 & 11).
Step-11 Verify the distance and move the front bracket assembly if necessary (Fig 12). Tighten the bolt.
Step-12 Assembly the rear clamp bracket with the rear bracket using (1) ¼” x 1” button head screws (1) ¼” lock washer and (1) ¼” hex nut. (1-2 turn thread), (Fig 13).
Step-13 Open the rear door, measure from the front clamp approximately 36 5/8”, use tape to delimit. Position the rear foot bracket into the rain gutter. Hook the clamp rear bracket in the door frame (Fig 14 & 15).
Step-14 Verify the distance and move the rear bracket assembly if necessary. Tighten the bolt.
Step-15 Repeat step 9 to 13 to attach the brackets on the passenger side.
Step-16 With assistance position the Ceros roof rack assembly on the assembly brackets. Attach the foot brackets to the Ceros roof rack crossbars in the previously installed ¼” x 1” hex bolts, using (2) ¼” flat washers, (2) ¼” lock washers and (2) ¼” hex nuts for each bracket , (Fig 16). Snug but do not tighten the hex nuts.
Step-17 Adjust and align the Ceros roof rack assembly as necessary and fully tighten all hardware.
LIMITED WARRANTY
Go Rhino warrants to Buyer that for a period of five (5) years from the date of shipment of the product(s) (“Warranty Period”) for black finishes and chrome finishes, that such products will materially conform to the specifications set forth in Go Rhino’s specifications in effect as of the date of shipment(s) and will be free from material defects in material workmanship.
Go Rhino warrants to Buyer that for the life of the product(s) from the date of shipment of the product(s) (“Warranty Period”) for polished stainless steel finished products purchased after April 2004, that such products will materially conform to the specifications set forth in Go Rhino’s specifications in effect as of the date of shipments and will be free from material defects in material workmanship.
Warranty claims must be accompanied with the original invoice and photos of the product. It is the customer’s responsibility to clean regularly and protect finish with regular applications of a nonabrasive polish that is compatible with the product’s finish.
This warranty covers the cost of the product only and does not include the cost of removal, installation, third party modifications or shipping of the product. In no event shall Go Rhino be liable to buyer or any third party for any damage or harm caused by the product or use thereof, regardless of weather such damages were foreseeable and whether or not Go Rhino has been advised of the possibility of such damages, not withstanding the failure of any agreed or other remedy of its essential purpose. This warranty is void if the product shows signs of alteration, misuse, mishandling, improper care, neglect, improper application and/or damage due to improper installation.
With respect to any such product(s) during the limited warranty period, Go Rhino shall, in its sole discretion, either: (i) provide a one-time repair or replacement of such products (or the defective part) or (ii) credit or refund the price of such products at the pro rata contract rate provided that, if Go Rhino so requests, Buyer shall, at Go Rhino’s expense, return such product(s) to Go Rhino. The remedies shall be the Buyer’s sole and exclusive remedy and Go Rhino’s entire liability for any breach of the limited warrant(ies).
Go Rhino disclaims all other warranties except to the extent that any such warranty cannot be validly disclaimed under applicable law.
Finish Limited Warranty:
Limited lifetime on stainless steel products (after April 2004)
5 year warranty on black powder coat products
5 year warranty on chrome products
This warranty does not cover exposed welds
Finish warranty covers peeling, flaking, or cracking. Washing all finishes regularly with car wash soap and rinsing well with water is the best method for maintaining the finish on your products. You must also protect the finish with nonabrasive automotive wax on a regular basis. The use of any compound which contains abrasives becomes a self-defeating exercise as the compound scratches the finish and opens it to corrosion. The use of harsh chemicals used to remove bugs and tar may also cause the finish to fail and should be avoided.
If you are unsatisfied with your purchase please contact the establishment you purchased the product from.
If you need to place a warranty claim or need assistance, the Go Rhino customer service team will answer any questions you may have. Please contact the Go Rhino customer service team at 1-888-427-4466 during normal business hours Monday thru Friday 7 am to 5 pm PST. You may also email warranty@gorhino.com. In order to better serve you please provide a copy of the original invoice / receipt, a photo of the issue you are experiencing and a photo of the vehicle the product is installed on.
All warranty returns must have an approved RGA number. The RGA number must be clearly marked on the exterior of the return package. All approved warranty returns must be shipped to Go Rhino Products, 1002 Carriers Drive, Laredo, Texas 78045.
PRODUCT REGISTRATION
Please remember to register your new purchase. You may register your product at www.gorhino.com. Registering your product may help speed any future warranty or customer service inquiries.
CUSTOMERS SUPPORT
Thank you again for purchasing from Go Rhino Products
Please take a few minutes to view additional products for your vehicle and
more at GORHINO.com
These installation instructions are available on the Go Rhino web site along
with installation videos for
many of our products.
www.gorhino.com
www.bigcountryauto.com
www.gorhinopd.com
© 2016 Go Rhino Products. All rights reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>