XPOtool 61847 Torque Wrench User Manual

XPOtool 61847 Torque Wrench User Manual

Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly. Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

Xpo the  tool

The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights re- served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing from you.
Send an e-mail to: [email protected] or use our contact form: https://www.wiltec.de/contacts/

The most recent version of this manual in various languages can be found in our online shop via: https://www.wiltec.de/docsearch

Our postal address is:
WilTec Wildanger Technik GmbH Königsbenden 12
52249 Eschweiler Germany
To return orders for exchange, repair, or other purposes, please use the following address. Attention! To allow for a smooth execution of your complaint or return, it is important to contact our customer service team before returning the goods. Returns Department
WilTec Wildanger Technik GmbH Königsbenden 28 52249 Eschweiler

** Thank you for purchasing this quality product. To minimise the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instruc- tions carefully and make sure you have understood its content.** Keep these operation instructions safe.

Safety notes and information

• Read all safety notes and Not observing the safety notes or instructions might result in serious injuries or damages.
• This torque wrench was calibrated before leaving the factory; it is accurate to ± 4 %. Neverthe- less, being a precision measuring device, it must be regularly calibrated and
• When using the device, make sure that the trigger value has been correctly set
• Never use the torque wrench to loosen screw
• Do not overload the torque Otherwise, the tool might be damaged and/or the trigger value falsified.
• Make sure to position the tool so that it cannot slip off the screw
• Do not use any extensions or articulations in order to increase the power
• After not being used for some time or after being stocked, operate the torque wrench several times at a low torque By doing so, a special inner lubricant re-coats the inner parts.
• Do not turn the handle below the lowest torque
• Do not turn the handle any further after the pre-set torque has been The pressure must be released from the handle for the wrench to be able to automatically reset itself. If after loos- ening the wrench pressure continues to be exerted, the recommended torque setting will be exceeded, which will lead to the part to be tightened being damaged.
• The torque wrench must be regularly maintained and For cleaning, use a tidy, dry cloth. Do not immerse the torque wrench in detergent for this might affect the lubricant that the wrench is equipped with.
• Always store the torque wrench at its lowest setting
• Before tightening screws, make sure that the threads are lightly oiled and free of
• Insert the torque wrench so that the desired torque is approximately in the middle of a scale range and not at its upper limit.

Operating the wrench

Caution! When setting the torque wrench, observe the vehicle manufacturer’s indications. ****

1. Take the torque wrench in your hand so that you always can see the Turn the knurled or hexagon screw counter-clockwise to release the lock.
2. Set the torque by turning the Proceed as follows:

Example: 130 Nm

**** First set the value of the upper edge of the rotary handle to 126 Nm by turning it clockwise. Make sure that the “0” position is exactly aligned with the midline of the setting scale.
Now turn the “4” on the rotary handle scale clockwise to the midline of the setting scale to set the value of 130 Nm.
Lock the handle by turning the knurled or hexagon screw clockwise. Now the torque is set to 130 Nm, and the torque wrench ready to be used.
3 The socket wrench insert now must be placed on the square drive of the socket wrench. After- wards place it on the nut or the screws and tighten. Make sure that tightening is quick, but not Tighten until you feel and/or hear the wrench click.
Loosen tension, and the torque wrench is automatically reset for the next operation.

After loosening the wrench, do not tighten it further!

Use extra care with low torques being set with the wrench clicking.

Technical specifications

Important notice:

The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction manual require the written permission of WilTec Wildanger Technik GmbH.

Read More About This Manual & Download PDF:

References

• WilTec - Ihr Online Shop für Haus, Garten, Werkstatt, Freizeit

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>