IUKNOB IU-32 Double Keypad Door Knob User Guide
- June 13, 2024
- IUKNOB
Table of Contents
- Required tools (not included)
- Prepare the door and check dimensions
- Install the rosette rubber
- Fix the mounting plate
- Specifications
- Passcode
- Indicator light signals and beep
- Mobile remote code
- [
- Synchronize Passcode
- Restore Factory Settings
- Programming
- PASSCODE
- BEEPER
- PASSAGE
- ADVANCED
- REMOTE
- Troubleshooting
- Warranty
- Important Safeguards
- Documents / Resources
IUKNOB IU-32 Double Keypad Door Knob User Guide
Required tools (not included)
Ruler
Philips head screwdriver
Hammer
Chise
- A. Key x 4
- B Rubber grip x 2
- C Exterior Assembly
- D Spindle
- E Rosette rubber
- F Latch
- G Latch screw x 4 (M4*20mm)
- H Mounting rubber
- I Mounting plate
- J Mounting Screws x 2 (M4*40mm)
- K Interior Assembly
- L Mounting Screws x 3 (M4*20mm)
- M Interior Cover
- N M3*8mm
- O Strike plate
- P Plastic box
Prepare the door and check dimensions
- Measure your door for a backset of the 2-3/8″or 2-3/4″. If it is 2-3/4″, adjust the latch as follows: Grasp the spring pin and move it from the 2-3/8″ slot to 2-3/4″ slot.
- Confirm the door is between 1-3/8″ to 2-3/4″ thick.
Install the latch and strike plate
Install the rosette rubber
Align the rubber(gasket)(1) with the two protrusions(2) of the rosette(3).
then press the rubber(gasket)(1) along the edge of the rosette(3).
Install the spindle
Press the protrusion(2) of the spindle(1) and push it into the keyway(3) of the exterior assembly.
For doors thicker than 2 “, please use additional option spindles.
Insert the exterior keypad
Align the exterior keypad with the hole of the door(2). Thread the power
cable(1) through the hole of the door(2) and make sure it is above the
latch(4). The spindle(3) on the exterior keypad should be aligned with the
hole in the center of the latch. Insert the spindle(3) through this hole as
you press the exterior keypad against the door.
Install the mounting plate
Thread the power cable(1) through the hole of the mounting rubber(3) and the
mounting plate(2) in turn.
Fix the mounting plate
Tighten the two mounting screws(1)evenly.
Connect the power cable
Plug the power cable(1) into the connector(2) of the interior assembly(4).
Set the SYNC switch(3)
Please refer to Synchronize Passcode
Install the interior keypad
Align the interior assembly(3) with the spindle(2). Press the interior
assembly(3) against the door. Make sure the power cable(1)do not get stuck by
the interior assembly(3), then tighten the three mounting screws(4) evenly.
Install the batteries and cover
Install the batteries(1) and the interior cover(3). Then tighten the screw(2).
Specifications
- Two ways to access: code or key.
- -22 F to +176 F temperature range.
- Low power consumption, 4 AAA for 1 Year Battery Life or 10,000 times unlock.
- Backlit keypad for use in low light environments.
- 1 master code , 50 user codes (each knob).
- Built-in mobile remote code.
- Passage mode for hassle-free entry.
- Programmable Auto-lock mode or Manual-lock mode.
- Low battery warning indication.
Passcode
Master passcode
- The master code MUST EXIST and can be modified, but cannot be deleted.
- The lock comes preset with default master passcode 123456. Make sure to set a new master code which can be1-15 digits long as soon as you finish installing the lock.
- Used to put the lock in programming mode.
- Can unlock the lock.
- Must be different from all of the User Codes currently in the lock.
If you forget the master passcode, you can reset the lock to factory settings, which restores the default master passcode. For more information, please see Restore Factory Settings.
User passcode
- User codes can be added, modified, deleted.
- Can be 1-15 digits long.
- The lock comes preset with no user codes.
- Used to unlock the lock.
- Must be different from the master passcode and other user passcodes.
- Up to 50 possible user codes can be stored in the lock at one time.
Passcode Disguise
This function is an added security feature which is aimed at preventing
passcode theft. With
Passcode Disguise, you may enter up to 40 digits into the keypad. As long as
the correct passcode sequence is entered, regardless of how many digits were
entered before or afterwards, the lock will unlock.
For example, if your user passcode is “112256“, you can successfully unlock the lock by entering “112256”(limit 40 digits).
Unlock with passcode
ENTER | PRESS |
---|---|
master code or user code |
Indicator light signals and beep
The color of the light indicates & beep ,the status of the lock.
Green
- A correct master passcode or user passcode was entered ,one long beep
- The programming process is complete ,one long beep
Red
- An incorrect master passcode or user passcode was entered, three short beeps
- There was an error in programming, three short beeps
- red blinking and beep after keypad backlit off indicates critically low battery
Mobile remote code
The code is generated by the website. You can set the unlock times or unlock time periods on the website page. If it exceeds the set number of times or time period, it will become invalid automatically. You do not need to program locks. Therefore, you can remotely authorize this remote code to your relatives, friends, neighbors, hourly workers, classmates or employees to enter your home, room or office.
Please visit mylock.iulock.com or scan the QR code below to access the website.
- Register account.
- Add lock ( Serial number of the lock).
- Activate your lock.
- Use remote code.
For remote code instructions , please visit www.iulock.com
[
Synchronize Passcode
Code synchronization is designed for convenience of passcode settings of
double keypad.
Back of interior assembly
When the switch is in the sync position
Any changing passcode settings on any keypad will be synchronized to another
keypad. Synchronization is only applicable to change the passcodes and reset
the lock.
When the switch is not in the sync position
The exterior keypad and the interior keypad are completely independent. The
settings and reset of the two keypads do not affect each other.
Restore Factory Settings
Code synchronization is designed for convenience of passcode settings of To
delete all user codes, including the master code, follow the instructions
below:
- Use a screwdriver to remove the screws from the interior cover.
- Remove the cover and find the reset button located on the battery pack.
- Press and hold the reset button for 7 seconds until a long beep is heard. The master passcode will return to the manufacturer default code ‘123456’.
Settings | Default |
---|---|
Master code | 123456 |
User code | Not preset |
Beeper | Enable |
Passage mode | Disable |
Lock mode | Auto-lock mode |
Auto-lock timer | 4 seconds |
Remote code | Deactivated |
Programming
»If you make a mistake during programming ,press the check button repeatedly until the keypad lights up. Then start over.
PASSCODE
ADD USER PASSCODE
Press| Press| Press| Enter| Press| Enter| Press| Enter same| Press
| | | Master passcode| | New user passcode| | New user passcode|
Note : The New User Passcode must be different from all of the Passcodes
currently in the lock.
CHANGE MASTER PASSCODE
Press| Press| Press| Enter| Press| Enter same| Press| Enter| Press| Enter
same| Press
| | | Master passcode| | master passcode| | New master passcode| | New master
passcode|
A Note : The master code MUST EXIST in the lock and cannot be
deleted, but can ONLY be changed.
CHANGE USER PASSCODE
Press| Press| Press| Enter| Press| Enter| Press| Enter| Press| Enter same|
Press
| | | Master passcode| | Unwanted user passcode| | New user passcode| | New
user passcode|
Note : The New user passcode must be different from all of the passcodes
currently in the lock.
DELETE A USER PASSCODE
Press| Press| Press| Enter| Press| Enter| Press
| **| | Master passcode| | Unwanted user passcode|
DELETE ALL USER PASSCODES|
---|---
Press| Press| Press| Enter| Press| Note** :The master code cannot be
deleted, but can ONLY be changed.
BEEPER
DISABLE BEEPER
Press| Press| Press| Enter| Press| Press| Press
| | | Master passcode| | |
ENABL E **B A E U E D P I O
E R**
Press| Press| Press| Enter| Press| Press| Press
| ****| | Master passcode| | |
The beeper can be turned off if desired.
Beepers will still sound to indicate a low battery.
PASSAGE
E A N S A Y B P L A E SSAG
E MODE| With EASY PASSAGE MODE active, the door will stay unlocked. Press
any button to turn off this function when it is no longer needed.
---|---
Press| Press| Press| Enter| Press
| **| | Master passcode|
A E D N V A A B N L C E E
A D U P D A I S O SAG E MODE*|
With ADVANCED PASSAGE MODE active, open the door by twisting door handle
directedly. Turn off this mode only by entering master code and check key.
Press the check button 4 times in a row , the door will be immediately locked,
which overrides any working modes.
Press| Press| Press| Enter| Press| Press| Press
|
| | Master passcode| | |
ADVANCED
A E U N T A O B – L L E O
C A K U D M I OD E| In AUTO-LOCK MODE,
the door will automatically lock after each unlocking, the auto-lock time
depends on the setting of the auto-lock timer.* Press the check button 4 times
in a row, the door will be immediately locked, which overrides any working
modes.
---|---
Press| Press| Press| Enter| Press| Press| Press
|
| | Master passcode| | **|
M E N A A N B U L A E L –
A L O U D C I K O M OD E**| In
MANUAL LOCK MODE, the auto-lock will turn off. After unlocking the door with a
passcode or fingerprint, it will remain unlocked until any button is pressed.
---|---
Press| Press| Press| Enter| Press| Press| Press
| | | Master passcode| | |
REMOTE
E ANCA T I B V L A E T E A
R U E D M I O OT E CODE FEATURE| The
activate code is generated by the website,(www.mylock.iulock.com) Deactivate
remote code function when the activate code is 0.
---|---
Press| Press| Press| Enter| Press| Enter| Press
| ****| | Master passcode| | Activate code|
Troubleshooting
The lock doesn’t work?
Try replacing the battery or using the backup battery. If the lock still does
not work, contact customer support.
Why can’t I open the door?
You may be waiting too long to open the door. After entering a code, turn the
handle to open the door while the lock LED indicator light is green.
Once the LED indicator light is off, the lock will return to locked position
immediately.
Why I can open without passcode?
You maybe active the passage mode, use master code access will turn off this
function .
If you just installed it, make sure the “THIS SIDE UP” on the spindle is
facing up (ceiling).
I forgot all my codes.
The lock must undergo a hard reset in order to set the master code back to
default and erase all other codes. In order to perform a hard reset,please
refer to the above “Restore Factory Settings”.
If none of the above information resolves your issue, please visit our
website at:www.iulock.com
Warranty
Lifetime Limited Mechanical and Finish Warranty and 1-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, IULOCK extends a lifetime limited mechanical and finish warranty and a one year limited electronics warranty to the original consumer user (“Original User”) of our IULOCK brand product (“Product”) against defects in material and workmanship, as long as the Original User occupies the residential premises upon which the Product was originally installed. See answers www.iulock.com for specific warranty details and limitations
Important Safeguards
- Read all instructions in their entirety.
- Familiarize yourself with all warning and caution statements.
- Remind all family members of safety precautions.
- Protect your user passcode and master passcode.
- Dispose of used batteries according to local laws and regulations
WARNING:
This Manufacturer advises that no lock can provide complete security by itself. This lock maybe defeated by forcible or technical means. or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
Template
Documents / Resources
|
IUKNOB IU-32 Double Keypad Door
Knob
[pdf] User Guide
IU-22, IU-32, IU-32 Double Keypad Door Knob, IU-32, Double Keypad Door Knob,
Keypad Door Knob, Door Knob, Knob
---|---
References
- iuLock - Smart Lock
- IULOCK – IU-20 smart door knob IU-20 keypad door knob IU-20 electronic door knob Simple is always better !
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>