IUKNOB IU-40 Fingerprint Door Lock User Guide

IUKNOB IU-40 Fingerprint Door Lock

Required Tools (not included)

• Ruler

• Philips head screwdriver

• Hammer

• Chisel

Lock Components

Prepare The Door And Check Dimensions

Use the template to mark holes

Drill two holes

Check dimensions

Install The Latch And The Strike Plate

Setting latch（2-3/8″ or 2-3/4″）

Measure your door for a backset of the 2-3/8″or 2-3/4″. If it is 2-3/4″,
adjust the latch as follows: Grasp the spring pin and move it from the
2-3/8″ slot to 2-3/4″ slot.(Backset 2-3/8” or 2-3/4”)

Install the latch

Install the strike plate

Install The Exterior Keypad And The Interior Assembly

Install the exterior keypad

Make sure that “THIS SIDE UP” of the spindle is facing up.

Align the exterior keypad with the bore hole. Feed the power cable through latch.
The spindle on the exterior keypad should be aligned with the hole in the center of the latch. Insert the spindle through this hole as you press the exterior keypad against the door.

Install the interior assembly

Route the power cable through the hole in knob and guide the spindle into the handle.

Push out the power cable

Do not pull the power cable too hard.
Make sure the inside knob turns easily.

Install The Batteries And Perform The Door Handing Process

Install The Interior Cover

Features

• Three ways to access: fingerprint, code or key.
• -22 F to +176 F temperature range.
• Low power consumption, 4 AAA for 1 Year Battery Life or 12,000 times unlock.
• Backlit keypad for use in low light environments.
• 1 master code , 50 user codes , 100 fingerprints.
• Built-in mobile remote code.
• Passage mode for hassle-free entry.
• Built-in disguise feature to protect your codes from prying eyes.
• Low battery warning indication .

Keypad

Programming Guide

Indicator light signals and beep

The color of the light indicates & beep ,the status of the lock.

Green

. a correct passcode was entered ,one long beep
. a correct fingerprint was scanned, one long beep
. the programming process is complete ,one long beep

Red

. an incorrect passcode was entered ,three short beep
an incorrect fingerprint was scanned, three short beep
. there was an error in programming, three short beep
. red blinking and low battery voice indicates critically low battery

Passcode and Passcode Disguise

Master passcode

• The master code MUST EXIST and can be modified, but cannot be deleted.
• The lock comes preset with default master passcode 123456.
• Make sure to set a new master code which can be1-15 digits long as soon as you finish installing the lock.
• Used to put the lock in programming mode.
• Can unlock the lock.
• Must be different from all of the User Codes currently in the lock.

User passcode

• User codes can be added, modified, deleted.
• Can be 1-15 digits long.
• The lock comes preset with no user codes.
• Used to unlock the lock.
• Must be different from the master passcode and other user passcodes.

Passcode Disguise

This function is an added security feature which is aimed at preventing passcode theft. With Passcode Disguise, you may enter up to 40 digits into the keypad. As long as the correct passcode sequence is entered, regardless of how many digits were entered before or afterwards, the lock will unlock.
For example, if your user passcode is “112256“, you can successfully unlock the lock by entering “112256”(limit 40 digits).

Unlock with passcode

Green and one long beep

Code correct, you can turn the knob to open the door immediately, and it will be automatically locked later (the automatic locking time depends on the setting of the automatic locking timer, the default is 4 seconds).

Red and three short beeps

The code is incorrect, please re-enter the correct code and press the check button to confirm.

Unlock with fingerprint

Green and one long beep
Fingerprint correct, you can turn the knob to open the door immediately, and it will be automatically locked later (the automatic locking time depends on the setting of the automatic locking timer, the default is 4 seconds).

Red and three short beeps
Fingerprint is incorrect, please re-scan the fingerprint.

Unlock with key

Insert the key and rotate the key. The first quarter turn should be very easy, then continue to turn the key to retract the latch and you may need to apply some force.
Tips : Turning the handle with the other hand in the same direction while you are turning the key will make it easier to open.
Note : Because the knob is relative heavy and the mechanical key of this electronic door knob is completely independent, so using the key requires a little more force than the common mechanical lock.

Immediate Lock

Press the check button 4 times in a row at any time and the door will be immediately locked, which overrides any other working modes.

Restore Factor y Settings

To delete all user codes, including the master code, follow the instructions below:

1. Use a screwdriver to remove the screws from the interior cover.
2. Remove the cover and find the reset button located on the battery pack.
3. Press and hold the reset button for 7 seconds until long beep are heard. The master passcode will return to the manufacturer default code ‘123456’.
   

After restore factory , Change the master passcode as soon as possible because the master passcode can unlock the door.

Mobile Remote Code

The code is generated by the website. You can set the unlock times or unlock time periods on the website page. If it exceeds the set number of times or time period, it will become invalid automatically. You do not need to program locks. Therefore, you can remotely authorize this remote code to your relatives, friends, neighbors, hourly workers, classmates or employees to enter your home, room or office.

Please visit mylock.iulock.com or scan the QR code below to access the website.

1. Register account.
2. Add lock (Serial number of the lock).
3. Activate your lock.
4. Use remote code.

For remote code instructions, please visit www.iulock.com

Programming

Command mode

FINGERPRINT

REGISTER FINGERPRINT|
---|---
Press| Press| Press| Press| Enter| Press| Scan fingerprint 6 times according to voice navigation. Succeed each time with a short beep.
| | | | Master passcode|
DELETE FINGERPRINT|
---|---
Press| Press| Press| Press| Enter| Press| Scan unwanted fingerprint
| | | | Master passcode|
DELETE ALL FINGERPRINT|
---|---
Press| Press| Press| Press| Enter| Press|
| | | | Master passcode|

PASSCODE

ADD USER PASSCODE|
---|---
Press| Press| Press| Enter| Press| Enter| Press| Enter| Press
| | | New user passcode| | New user passcode| | New user passcode|
Note : The New User Passcode must be different from all of the Passcodes currently in the lock.
CHANGE MASTER PASSCODE| | |
---|---|---|---
Press| Press| Press| Enter| Press| Enter same| Press| Enter| Press| Enter same| Press
| | | Master passcode| | master passcode| | New master passcode| | New master passcode|
Note : The master code MUST EXIST in the lock and cannot be deleted, but can ONLY be changed.| |
CHANGE THE USER PASSCODE

Press| Press| Press| Enter| Press| Enter| Press| Enter| Press| Enter| Press
| | | Master passcode| | Unwanted user passcode| | New user passcode| | New user passcode|
Note : The New user passcode must be different from all of the passcodes currently in the lock.
DELETE USER PASSCODE

Press| Press| Press| Enter| Press| Enter| Press
| | | Master passcode| | Unwanted user passcode|
DELETE ALL USER PASSCODES|
---|---
Press| Press| Press| Enter| Press| Note : The master code cannot be deleted, but can ONLY be changed.
| | | Master passcode|

BEEPER

ENABLE KEY TONE

Press| Press| Press| Enter| Press| Press| Press
| | | Master passcode| | |
DISABLE KEY TONE

Press| Press| Press| Enter| Press| Press| Press
| | | Master passcode| | |

PASSAGE

EASY PASSAGE MODE| With EASY PASSAGE MODE active, the door will stay unlocked. Press any button to turn off this function when it is no longer needed.
---|---
Press| Press| Press| Enter| Press
| | | Master passcode|
ADVANCED PASSAGE MODE| With ADVANCED PASSAGE MODE active, open the door by twisting the handle directly. Turn off this mode only by entering master code and check key. * Press the check button 4 times in a row , the door will be immediately locked, which overrides any working modes.
---|---
Press| Press| Press| Enter| Press| Press| Press
| | | Master passcode| | |

ADVANCED

AUTO-LOCK MODE| In AUTO-LOCK MODE the door will automatically lock after each unlocking, the auto-lock time depends on the setting of the auto-lock timer. * Press the check button 4 times in a row, door will be immediately locked, which overrides any working modes.
---|---
Press| Press| Press| Enter| Press| Press| Press
| | | Master passcode| | |
MANUAL LOCK MODE| In MANUAL LOCK MODE the auto-lock will turn off.
After unlocking the door with a passcode or fingerprint, it will
remain unlocked until any button is pressed.
---|---
Press| Press| Press| Enter| Press| Press| Press
| | | Master passcode| | |
ENABLE AUDIO SET AUTO-LOCK TIMER| The automatic lock time unit is seconds. Minimum is 2 seconds. Maximum is 43200 seconds (12 hours). Default is 4 seconds.
---|---
Press| Press| Press| Enter| Press| Press| Press| Enter| Press
| | | Master passcode| | | | Auto-lock timer|
ACTIVATE REMOTE CODE FEATURE| The activate code is generated by the website,(www.mylock.iulock.com) Deactivate remote code function when the activate code is 0.
---|---
Press| Press| Press| Enter| Press| Enter| Press
| | | Master passcode| | Activate code|

Voice navigation mode

Troubleshooting

The lock doesn’t work?
Try replacing the battery or using the backup battery. If the lock still does not work, contact customer support.
Why can’t I open the door?
You may be waiting too long to open the door. After entering a code, turn the handle to open the door while the lock LED indicator light is green. Once the LED indicator light is off, the lock will return to locked position immediately.
Why I can open without passcode?
You maybe active the passage mode, use master code access will turn off this function .
If you just installed it, make sure the “THIS SIDE UP” on the spindle is facing up (ceiling).
I forgot all my codes.
The lock must undergo a hard reset in order to set the master code back to default and erase all other codes. In order to perform a hard reset, please refer to the above “Restore Factory Settings”.
If none of the above information resolves your issue, please visit our website at: www.iulock.com

Warranty

Lifetime Limited Mechanical and Finish Warranty and 1-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, IULOCK extends a lifetime limited mechanical and finish warranty and a one-year limited electronics warranty to the original consumer user (“Original User”) of our IULOCK brand product (“Product”) against defects in material and workmanship, as long as the Original User occupies the residential premises upon which the Product was originally installed .See answers www.iulock.com for specific warranty details and limitations.

Important Safeguards

1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user passcode and master passcode.
5. Dispose of used batteries according to local laws and regulations.

Template

WARNING This Manufacturer advises that no lock can provide complete security by itself. This lock maybe defeated by forcible or technical means. or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.

References

• iuLock - Smart Lock
• IULOCK – IU-20 smart door knob IU-20 keypad door knob IU-20 electronic door knob Simple is always better !

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>