AROFLY 4718009140073 Link A1 Power Meter + Cadence Sensor Bundle User Manual

Intelligent Dynamic Pressure Technology
USER MANUAL

PACKAGE CONTENTS

INSTALLING AROFLY POWER METER ON CYCLE REAR VALVE ONLY

Tips: Before installing AROFLY power meter to the rear tire valve, please inflate the bike tires to appropriate tire pressure as marked on the tire. Suggest the road bike to be 90~120psi (6~8bar); Mountain bike to be 35~65psi (2.4~4.5bar) Before using AROFLY power meter, twist open the cap, then remove the INSULATION TAB, from between the battery contact.

Place Wrench onto the AROFLY Base.
Twist counter-clockwise to open AROFLY Cap.| Pull and remove Insulation Tab from AROFLY to connect battery. Replace
the cap to AROFLY.

Installing AROFLY to the cycle rear valve: If it is a Schrader valve, please install directly; If it is a Presta valve, please use the Presta valve adaptor first, included in the kit, before installing the AROFLY power meter.

INSTALLING CADENCE SENSOR ON CYCLE LEFT CRANK ONLY
Using the rubber ties included, secure the cadence sensor to the inner side of the cycle left crank.

Attach the cadence sensor to the inner side of the cycle left crank for best performance
Tips: Insert the battery to Cadence Sensor

MOUNTING THE LINK TRANSMITTER

1. Use the proper size of Rubber ties (included in this package) to fix the “Holder” on the bike Handlebar or Stem.
2. Slide the “LINK Transmitter” into the “Holder” starting from the front of the bracket, as shown in the picture.
3. Use the Rubber Tie(included), to secure the “LINK Transmitter” on the Holder. (Ensure the Rubber Tie is secure in the holder groove.)

Remark: For your Attention: After installation of the “LINK”, there must be no other device or equipment in front of the “LINK Transmitter”.
LINK TRANSMITTER: BUTTONS AND LED STATUS

Buttons, ON/OFF

• Power ON: Press and hold the Power button for 3 seconds.( B )
• Power OFF: Press and hold the Power button for 3 seconds.(B  )
• INDOOR/OUTDOOR Mode: On the “LINK”, press once on the INDOOR/  OUTDOOR mode button to switch.(A  )
• Paring: On the “LINK”, simultaneously press and hold the INDOOR/ OUTDOOR mode button and the Power ON/OFF button.( +  )

LINK TRANSMITTER: BUTTONS AND LED STATUS

LED STATUS

1. AROFLY LED Activity On The LINK TRANSMITTER
   • Solid green: “LINK”, not connected with the AROFLY power meter.
   • Solid blue: “LINK”, connected with the AROFLY power meter.
   • Flashing red: On the “LINK”, indicates the battery of the AROFLY power meter is low.
   • Solid red: On the “LINK”, it is a warning message, please check the status on the “AROFLY 2” APP.
   • Alternating green, blue, and red: The “LINK” is attempting to pair with the AROFLY power meter.

2. LED Activity On The LINK TRANSMITTER Showing Connection With Other Bike Computers Or With The “AROFLY 2” APP.
   • Flashing red: On the “LINK”, indicates the battery of the “LINK” is low.
   • Solid red: On the “LINK”, indicates the “LINK” battery is charging.
   • Red OFF: On the “LINK”, indicates the “LINK” battery has been completed charged.
   • Solid blue: On the “LINK”, indicates transmitting ANT+ and BLE signals simultaneously. Check the connection status on the devices (Bike Computers or the “AROFLY 2” APP).

3. Cadence LED Activity On The LINK TRANSMITTER
   • Solid green: “LINK”, not connected with the Cadence sensor.
   • Solid blue: “LINK”, connected with the Cadence sensor.
   • Flashing red: On the “LINK”, indicates  the battery of the Cadence sensor is low.
   • Alternating green, blue, and red: The “LINK” is attempting to pair with the Cadence sensor.

4. INDOOR/OUTDOOR Mode, LED Activity
   • Solid blue: On the “LINK”, indicates Indoor mode, when riding indoor, please select the correct bike trainer  on the “AROFLY 2” APP.
   • Blue OFF: On the “LINK”, indicates the “LINK” is on Outdoor mode.

TO CONNECT WITH THE “AROFLY 2” APP AND TO SETUP THE LINK TRANSMITTER

1. Turn power ON the “LINK” and turn on Bluetooth, on your phone.
2. Open “AROFLY 2” APP, and click the connection icon , to search for the  “LINK” that you are currently using.
3. The LINK TRANSMITTER code will show on the “AROFLY 2” APP, click it to connect.
4. If connected with Heart Rate Monitor, click the “Heart Rate Monitor” in the Main page to pair.
5. Enter Set Up page, input requested details and then click  to start your  ride. Reminder: If using other GPS bike computers, Heart Rate Monitor should be paired with other GPS bike computers, not with “AROFLY 2” APP
6. Display real-time riding data
   Press to start the ride and display data.
   Press to end the ride.
   

Data Display:

• Speed
• Cadence
• Power
• Trip Time
• Trip Distance| • Rear Tire Pressure
• Ascent
• Left/Right Pedal Ratio
• Heart Rate
---|---

INDOOR/OUTDOOR MODE
On the LINK Transmitter, press once on INDOOR/OUTDOOR mode button to  switch the modes.
Reminder:
Tips:

•  When riding outdoor, please confirm the INDOOR/OUTDOOR mode LED   on LINK Transmitter is OFF.
• AROFLY measures power by tire pressure variation. When riding indoor, it only works on the bike trainer with rollers, for the rear tire of the bike.
• AROFLY, performs better on rollers without any resistance.
  When riding indoor, the Bike Trainer or Roller must be selected correctly on the “AROFLY 2” APP.
  

WARNING MESSAGES

When AROFLY LED  activity is solid red, please check below errors on the “AROFLY 2” APP and resolve.

• LOW TIRE PRESSURE: Action, inflate your tire pressure
• INDOOR MODE STILL ON: Action, switch the INDOOR mode OFF on the “LINK”
• CHECK VALVE: Action, correctly install AROFLY power meter again

SPECIFICATION

AROFLY Power Meter

LINK Transmitter

Cadence Sensor

CHANGE BATTERY

AROFLY Power Meter
When LED activity is flashing red, it means the “AROFLY Power Meter”  battery is low, replace with new battery.

LINK Transmitter
When LED activity2  is flashing red, it means the “LINK” battery is low. Please use the USB cable included in the package to charge the “LINK”. Cadence Sensor 3 When LED activity  is flashing red, it means the “Cadence Sensor” battery is low, replace with new battery.

ATTENTION

1.  Please follow the bicycle manufacturer’s instructions to regularly check your cycle tire-pressure, that it is at optimum level before installing AROFLY on the tire valve.
2. AROFLY is compatible with most Presta & Schrader cycle valves, but may not fit on other types of cycle valves.
3. AROFLY 2″ APP is compatible with most iOS and Android systems for smart phones, but does not guarantee to work with other operating systems due to the diversity.
4. Because of the system diversity, we can not guarantee compatibility with ertain heart-rate monitors
5. AROFLY power meter is NOT suitable on tubeless tires, because the sealant inside the tube, will damage the AROFLY sensor.
6. Please be sure to update the “LINK” software to the latest version.

WARRANTY

1. AROFLY comes with a 12 month warranty against manufacturer’s defects, or failure to work within the 12 months, from date of original purchase. Warranty cannot be transferred.
2. Warranty does not cover failure from, neglect, accidental damage, due to dropping, crushing, misuse, and failure to follow the instruction manual.
3. If the AROFLY is opened without the manufacturer’s assistance or any tampering with the electronic components, it will COMPLETELY VOID the WARRANTY.

Design & Manufacture by
TBS Group Corporation
www.arofly.com / Made in Taiwan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>