Panasonic ER-CNT1 Nose Ear Facial Trimmer Head Instruction Manual

: June 13, 2024
: Panasonic

Table of Contents

Safety precautions
Important information
Parts identification (Fig. 1)
Before use (Fig. 2)
How to use
Maintenance
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Panasonic ER-CNT1 Nose Ear Facial Trimmer Head Instruction Manual

Safety precautions

Follow these instructions.

To prevent accidents, injuries or damage to property, please follow the instructions below.

The following chart indicates the degree of damage caused by improper operation.

Warning
Indicates potential hazard that could result in serious injury or death.

Caution
Indicates potential hazard that could result in minor injury or property damage.

WARNING

Preventing accidents

Do not place within reach of children or infants. Do not let them use it.
- Putting parts or accessories in the mouth may cause an accident or injury.

Caution

Protecting the skin

Do not press the blade firmly against the skin.
Do not press the blade with excessive force or insert too deeply into your nostril/ear canal.
Do not touch the blade section (metallic section) of the inner blade.
Do not use this appliance for any purpose other than to trim nose hair, ear hair, outline eyebrows, moustache or beard.
- Doing so may cause injury to skin or hand.
Check the blades are not damaged or deformed before use.
- Failure to do so may cause injury to the skin

Note the following precautions

Do not share with your family or other people.
- Doing so may result in infection or inflammation.

Important information

Note the following precautions to avoid malfunction or deformation.
Do not bring the blade into contact with hard objects.
Do not drop or hit against other objects.
Be sure to place the protective cap on the head when carrying around or storing

Parts identification (Fig. 1)

A Head

Protective cap
Outer blade
Inner blade
Trimmings box
Water inlet
Water outlet
Wash switch ring
Filter
Exhaust hole

Before use (Fig. 2)

Be sure to close the water inlet of the wash switch ring during use. Otherwise, the main body cannot provide sufficient suction power. → Check that the marks of “ ”, “” and “” align

How to use

Clean the appliance after use

Mount the head to the main body until it clicks.
Remove the protective cap and hold the main body so as not to block the exhaust hole (a). (Fig. 3)
Turn on the power before putting the head in your nostril.
- Cut hairs using the tip of the outer blade (metallic part).
- The outer blade surface may get a little warm during use, but performance will not be diminished.

Note

The use time after a full charge is as follows.
ER-CBL1: Approximately 80 minutes
ER-CBN1: Approximately 60 minutes
(Based on dry using at 20 °C – 30 °C [68 °F – 86 °F])
The operating time may differ depending on the frequency of use and the operating method.

Quick charge (ER-CBL1 only)
Even though the battery runs out, you can use for 5 minutes after 3-minute charge.
(This will differ depending on usage.)

Removing and mounting the head (Fig. 4)

Removing and mounting the head

Make sure that the main body is turned off.

Remove
Remove the head while pushing the head release button (b).

Stand the head when it is removed.

Mount
Mount the head to the main body until it clicks.

Trimming your nose hair and ear hair (Fig. 5)

Trimming your nose hair and ear hair

Insert the tip of the outer blade into your nostril or ear canal.
- Insert it slowly so as not to injure your nostril or ear canal.
Cut the nose hair and ear hair by moving the main body.
- Some trimmings may remain inside your nostril or ear canal after cutting, so remove them using a tissue or similar.

Outlining your eyebrows, moustache, or beard (Fig. 6)

Outlining your eyebrows

Apply the tip of the outer blade to the hair (eyebrow, moustache or beard) you would like to cut.
Cut the hair by moving the appliance slowly against the direction of hair growth.
- You cannot trim the hair to length with this head.
- It is not suitable for the hair below 0.5 mm (1/64″).

Maintenance

Make sure that the main body is turned off.
After cleaning, be sure to store with the blades, the trimmings box and the protective cap attached

How to clean (Fig. 7)

How to clean

With water

Apply some hand soap and some water to the outer blade.
Turn on the power and turn off the power after 10 seconds. (Fig. 7-1)
Open the water inlet and turn on the power again.
Remove the head, the blades and the trimmings box
- If the trimmings box is removed, open the water inlet after attaching the trimmings box
Run water down the water inlet (Fig. 7-2), rinse well and turn off
Rinse them with running water.
- Cover the drainage outlet of washbasin to prevent the inner blade from flowing away. (Fig. 7-3)
Wipe off the water with a dry cloth and dry it well.
It will dry faster with the blades and the trimmings box removed

Notes

Note the following precautions to avoid malfunction and damage.
Do not use hot water or any detergents other than hand soap.
Do not wipe with thinner, benzine, alcohol etc.

With the cleaning brush (Fig. 8

cleaning brush

Remove the head, blades and the trimming box.
Brush off any hair trimmings from the head, blades and the trimming box.
- Be careful not to deform the inner blade.
- Be careful not to damage the filter.

How to open and close the water inlet (Fig. 9)

How to open and close the water inlet

Open
Rotate the wash switch ring until its “” mark aligns with the “ ” mark of the head to open the water inlet. (Fig. 9-1)

Close
Rotate the wash switch ring until its “” mark aligns with the “” mark of head. (Fig. 9-2)

Removing and mounting the trimmings box (Fig. 10)

Removing and mounting the trimmings box

Remove (Fig. 10-1)
Rotate the wash switch ring until its “” mark aligns with the “ ” mark of the head.

Mount (Fig. 10-2)

Align the “” mark of the trimmings box with the “ ” mark of the head.
- Be careful not to damage the filter with the shaft (c).
Rotate the wash switch ring until its “” mark aligns with the “” mark of the head

Removing and mounting the blade (Fig. 11)

Removing and mounting the blade

Outer blade

Remove
Rotate the outer blade in the direction of the arrow and remove the blade.(1)

Mount
Insert the head’s shaft (d) into the hole of the inner blade.
Rotate the outer blade to align its “ ” mark with the “” mark of the head. (2)

Inner blade

Remove
Pull to remove the inner blade.

Mount
Insert the inner blade straight into the outer blade.