SEALEY LED3606G Rechargeable 360° Inspection Lamp Instruction Manual
- June 13, 2024
- SEALEY
Table of Contents
SEALEY LED3606G Rechargeable 360° Inspection Lamp
Product Information
Thank you for purchasing a Sealey product. This product is manufactured to a
high standard and, if used according to the instructions provided and properly
maintained, it will give you years of trouble-free performance.
Important: Please read these instructions carefully. Note the safe
operational requirements, warnings, and cautions. Use the product correctly
and with care for the purpose for which it is intended. Failure to do so may
cause damage and/or personal injury and will invalidate the warranty. Keep
these instructions safe for future use.
Safety General
- Ensure the light is fully charged before initial use.
- Do not turn the light on when it is being charged.
- Do not shine directly into your, other persons’, or animals’ eyes.
- Do not allow children to use the light.
- Do not handle or move the light while it is being charged.
- Do not use the light if you suspect that the battery or the light casing is damaged.
- Do not leave the battery in a discharged state. Recharge the battery immediately. Before storage, fully recharge the battery. Subsequently, recharge the battery at least once every six months of non-use.
Battery Safety
Warning: To reduce the risk of burns or fire:
- Do not attempt to open, dismantle, modify, or service the battery pack.
- Do not crush, puncture, short external contacts, or dispose of in fire or water.
- Replace only with the battery pack designated for this product.
- Recycle or dispose of used batteries as stipulated by local regulations.
- If the electrolyte in the cells gets on your skin, wash thoroughly with soap and water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.
Product Specification
- Model No: LED3606R, LED3606G
- Battery: 3.7V 2.6Ah Li-ion (x2)
- Charging Time: 7hr
- IP Rating: IP54
- LED Type: 15W + 3W SMD Side(High/Low)/Top – (1000/300)/150lm
- Maximum Length: 276mm
- Minimum Length: 256mm
- Operating Time: Side(High/Low)/Top – (3/12)/15hr
SAFETY
GENERAL
- Ensure the light is fully charged before initial use.
- DO NOT turn the light on when it is being charged.
- DO NOT shine directly into your, other persons’ or animals’ eyes.
- DO NOT allow children to use the light.
- DO NOT handle or move the light whilst it is being charged.
- DO NOT use the light if you suspect that the battery or the light casing is damaged.
- DO NOT LEAVE THE BATTERY IN A DISCHARGED STATE, RECHARGE THE BATTERY IMMEDIATELY. BEFORE STORAGE,
- FULLY RECHARGE THE BATTERY, SUBSEQUENTLY RECHARGE THE BATTERY AT LEAST ONCE EVERY SIX MONTHS OF NON-USE.
BATTERY SAFETY
WARNING: To reduce the risk of burns or fire:
- DO NOT Attempt to open, dismantle, modify, or service the battery pack.
- DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
- DO NOT Expose to temperatures above 60°C (140°).
- Replace only with the battery pack designated for this product.
- Recycle or dispose of used batteries as stipulated by local regulations.
- If the electrolyte in the cells gets on your skin, wash thoroughly with soap and water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.
INTRODUCTION
The unique and innovative 360° swivel and tilt function enables the light source to be positioned in any direction. Exclusive patented design owned by and registered to Sealey. 15W SMD LED with magnified lens providing up to 1000 lumens output with 120° spread of light, illuminating the whole work area. Includes an additional high-power 3W LED directional torch. Features two swivel hooks and three rubber-covered magnets, two on the rear and one on the end, which allow hands-free operation. Two high-quality 3.7V 2.6Ah lithium-ion batteries in parallel for up to 15 hours run time. Micro USB charging port. Supplied with USB cable.
SPECIFICATION
Model No: | LED3606 Red, Green |
---|---|
Battery: | 3.7V 2.6Ah Li-ion (x2) |
Charging Time: | 7hr |
IP Rating: | IP54 |
LED Type: | 15W + 3W SMD |
Lumen Output: | Side(High/Low)/Top – (1000/300)/150lm |
Maximum Length: | 276mm |
Minimum Length: | 256mm |
Operating Time: | Side(High/Low)/Top – (3/12)/15hr |
OPERATION
CHARGING
- To charge the light: insert the micro USB plug on the USB cable into the charging port on the back of the light (fig.1).
- Plug the other end of the USB cable into a 5V USB outlet.
- The charge indicator lights (fig.1) will light in sequence to show the current level of charge, each charge level is shown by a flashing green before becoming solid.
- Three solid green lights denote a full charge, at which point the light should be disconnected from the power supply.
USE OF LIGHT
Warning: Ensure that the lenses are not pointing in a dangerous direction before switching on.
- To switch the light on, press the function switch (fig.1) to select the required function:
- 1st push: Top light.
- 2nd push: Front light, low output.
- 3rd push: Front light, high output.
- 4th push: Off.
- When the light is switched on, the charge level will be shown by the number of green charge lights illuminated, three being a full charge.
- If only one green light is showing, the light requires recharging.
- To employ the 360° function, pull the base downward to release the ball joint. The light can then be positioned in any attitude relative to the base. Alternatively, the back magnets or 360° hooks may be used.
BATTERY REMOVAL
Remove the 6 screws on the back of the lamp. Remove the back casing and
disconnect the wiring from the circuit board. Remove the battery mounting
screws. Dispose of according to local government guidelines. Under the Waste
Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to
inform potential purchasers of products containing batteries (as defined
within these regulations), that they are registered with Valpak’s registered
compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number
(BPRN) is BPRN00705.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories, and packaging should be sorted, taken to a recycling center, and
disposed of in a manner that is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
- NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.
- IMPORTANT: No Liability is accepted for incorrect use of this product.
- WARRANTY: The guarantee is 12 months from the purchase date, proof of which is required for any claim.
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
CONTACT
- Sealey Group,
- Kempson Way,
- Suffolk Business Park,
- Bury St Edmunds,
- Suffolk. IP32 7AR
- 01284 757500
- sales@sealey.co.uk.
- www.sealey.co.uk.
- © Jack Sealey Limited
- LED3606R,
- LED3606G Issue: 2 – (H,3) 22/09/23
- MODEL NO: LED3606R, LED3606G
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>