XonTel XT-160AMP Amplifier VoIP PBX Phone Systems User Manual

June 13, 2024
XonTel

XonTel-logo

XonTel XT-160AMP Amplifier VoIP PBX Phone Systems

XonTel-XT-160AMP-Amplifier-VoIP-PBX-Phone-Systems-
image

Product Information

  • Product Name: XT-160AMP Amplifier
  • Functional Summary:
    • Built-in 2-UHF microphones A+B Chipset
    • UHF Frequency Range: 820MHz – 850MHz (Mic Optional)
    • Built-in Bluetooth Audio SoC, APT-X, HD audio-15m Distance Qualcomm
    • Extra microphone input Port with a 6.5mm interface
    • Audio Input, Rj09 Port
    • Wireless Remote uses 433Mhz frequency low power device UHF frequency Control-360-degree direction signaling technology-20M coverage
    • Support pairing multiple Amplifiers with 2 UHF microphones A&B Channel
    • Support Playing Music, Audio Sharing from one Mobile to multiple Amplifiers (Work with Android Mobiles Only)
    • Power Supply: AC115V-230V 47-63Hz
  • General Notes:
    • Use Cable Cat6 wire between Speakers & XT-160AMP, normal sound cables can be used but Cat6 will be more easy for you to fix inside the Amplifier Ports.
    • Use the External 1M Bluetooth antenna (PIC-01) Free included inside the XT-160 AMP box when you install the XT-160AMP inside the room ceiling.
    • Use a separate Electrical Power switch ON/OFF for your XT-160AMP inside your room (same as a light switch).
    • Make sure the room is a cool place, not more than 25°C.
    • Use 8 ohms Speakers, Each speaker not more than 20W, for 8-Ports Audio, Total maximum 160W Amplifier.
    • Make sure the XT-160 AMP Power OFF Position before you connect the AC to the Amplifier.

Product Usage Instructions

  1. Power on the Product:
  2. Make sure the AC source is in OFF Position.
  3. Connect the Amplifier UK power cord cable to the AC source.
  4. Turn ON the AC source then turn ON the Amplifier Power ON Switch in the back.
  5. The Amplifier will start to announce the Bluetooth ready tone, waiting for the user to connect the device for use.
  6. Remote Control:In the Normal situation, The Remote control is already PAIRED with the XT-160AMP (Amplifier) from the factory. Just try to Power ON/OFF the device using the Remote to check if the PAIR is OK.

Make sure the new Remote control has a new battery and the Red LED The remote is working when you press any Key.

1. Pair the Remote Control:
  1. Long press 2 seconds for the RC-Pair button which located behind the XT-160AMP (PIC-1), until you will hear a sound prompt tone saying (remote ready for pairing) and the Red LED behind the Amplifier will start Blinking.
  2. Press (Power) button No.1 in the Remote Control (PIC-2) for 3 Sec. You will hear (remote paired successfully) and the Red LED behind the Amplifier will STOP Blinking.
  3. Start using the Remote Control.
  1. Remote Control Functions:
    No.| Name| Function
    ---|---|---
    1| Power| ON / OFF + Pair New Remote Control / Press and hold to restore
    factory Settings
    2| MUTE| Mute/Unmute
    3| VOL+| Volume Up
    4| VOL-| Volume down
    5| PREV| Previous track
    6| NEXT| Next track
    7| PLAY/PAUSE|
    8| BT|
    9| AUX|
    10| MIC|
    11| BS+| Play/Pause Bluetooth ON/OFF Long press Bluetooth Pair
    12| BS-| Prompt tone volume down
  2. Reset Amplifier:Long press the (Power) button for 2 Seconds on the Remote control will restore factory Settings as below:
  3. Reset device volume to Level 15 (15/32)
  4. Clear the Bluetooth connection of any connected devices.
  5. Reset and open BT, AUX, MIC channels (same as BT ONAUX ONMIC ON)
  6. Mic PAIR will not be lost.
  7. Sound Broadcast the amplifier reset prompt tone.

Functional summary

  • 160W Amplifier- 8 ohms , (20Hz-20kHz)
  • 8-Ports Audio- maximum 160W(8×20W) , Can support up to 16 Speakers X 10W maximum each Port .
  • Built-in 2-UHF microphones A+B Chipset,UHF Frequency Range: 820MHz – 850MHz (Mic Optional).
  • Built-in Bluetooth Audio SoC,APT-X,HD audio-15m Distance Qualcomm.
  • Extra microphone input Port- with a 6.5mm interface.
  • Audio Input , Rj09 Port
  • Wireless Remote uses 433Mhz frequency low power device UHF frequency Control-360-degree direction signaling technology-20M coverage.
  • Support pairing multiple Amplifiers with 2 UHF microphones A&B Channel.
  • Support Playing Music , Audio Sharing from one Mobile to multiple Amplifiers ( Work with Android Mobiles Only ).
  • Power Supply : AC115V-230V (47-63Hz)

General Notes

  1. Use Cable Cat6 wire between Speakers & XT-160AMP , normal sound cables can be used but Cat6 will be more easy for you to fix inside the Amplifier Ports.
  2. Use the External 1M Bluetooth antenna (PIC-01) Free included inside the XT-160 AMP box ,when you install the XT-160AMP inside the room ceiling.
  3. Use a separate Electrical Power switch ON/OFF for your XT-160AMP inside your room ( same as a light switch ) .
  4. Make sure the room is a cool place, not more than 25c.
  5. Use 8 ohms Speakers , Each speaker not more than 20W , for 8-Ports Audio,Total maximum 160W Amplifier .
  6. Make sure the XT-160 AMP Power OFF Position before you connect the AC to the Amplifier.
  7. For more details Pls Watch : https://links.xontel.com/3RD1yBD

XonTel-XT-160AMP-Amplifier-VoIP-PBX-Phone-Systems-fig1

Start Up

Power on the Product:

  1. make sure the AC source is in OFF Position.
  2. Connect the Amplifier UK power cord cable to the AC source.
  3. Turn ON the AC source then turn ON the Amplifier Power ON Switch in the back.
  4. The Amplifier will start to announce the “Bluetooth ready” tone, waiting for the user to connect the device for use.

Remote Control :

In the Normal situation The Remote control is already PAIRED with the XT- 160AMP( Amplifier )from the factory. Just try to Power ON/OFF the device using the Remote to check if the PAIR is OK .
make sure the new Remote control has a new battery and the Red LED The remote is working when you press any Key .

Pair the Remote Control:

  1. Long press 2 seconds for the RC-Pair button which located in behind the XT-160AMP ( Pic-1 ) ,until you will hear a sound prompt tone saying ( remote ready for pairing ) and the Red LED behind the Amplifier will start Blinking.
  2. Press ( Power ) button No.1 in the Remote Control ( PIC-2) for 3 Sec. you will hear ( remote paired successfully ) and the Red LED behind the Amplifier wfor more details Pls Watch : https://links.xontel.com/3RD1yBDill STOP Blinking.
  3. start using the Remote Control.

XonTel-XT-160AMP-Amplifier-VoIP-PBX-Phone-Systems-fig3

General Informations about Bluetooth :

  • The BT button in the remote control is for ON/OFF the Bluetooth only.
  • Bluetooth coverage distance between 10M-15M in an open area.
  • XT-160AMP Limited to connect only one Mobile using Bluetooth at the same time .
  • If someone is using the Bluetooth and you do not know him, then you can Discharge (Dismissed) him from using the bluetooth by long pressing the BT button turn OFF/ON in the remote control.
  • Wireless Bluetooth name is XT-160AMP,If the connection between both XT-160AMP and your Mobile disconnected for any reason, the connection will not back automatically and you should reconnect them back again.
  • If you do not need anyone to connect to Bluetooth , Press BT button to turn OFF Bluetooth in the remote control.

Remote control Functions:

XonTel-XT-160AMP-Amplifier-VoIP-PBX-Phone-Systems-fig4

NO. Name Function
1 Power ON / OFF + Pair New Remote Control / Press and hold to restore

factory Settings
2| MUTE| Mute/Unmute
3| VOL+| Volume Up
4| VOL-| Volume down
5| PREV| Previous track
6| NEXT| Next track
7| PLAY/PAUSE| Play/Pause
8| BT| Bluetooth ON/OFF Long press Bluetooth Pair
9| AUX| AUX ON/OFF
10| MIC| Microphone ON/OFF Long press Microphone Pair
11| BS+| Prompt tone volume Up
12| BS-| Prompt tone volume down

Reset Amplifier :
Long press the (Power) button for 2 Seconds in the Remote control will restore factory Settings as below :

  1. Reset device volume to Level 15 (15/32)
  2. Clear the Bluetooth connection of any connected devices.
  3. Reset and open BT, AUX, MIC channels (same as BT ON\AUX ON\MIC ON)
  4. Mic PAIR will not be lost.
  5. Sound Broadcast the “amplifier reset” prompt tone

UHF Hand Mic ( MIC-02 ) XT-160AMP Support Max 2 Mic A+B Channels

XonTel-XT-160AMP-Amplifier-VoIP-PBX-Phone-Systems-fig5

  1. Press 2-3 Second the Power button to turn the Mic ON/OFF .
  2. Mic screen display : battery status , Working Channel and transmitting status.
  3. When the display is ON , short pressing the Power key will Mute/Unmute the Mic. transmitting status indicator will go OFF & ON .
  4. The Mic screen will go to sleep mode in 5 second , only Channel icon will be their the Mic will keep working , short press the Power button will wake up the screen again.
  5. Hand MIC-02 use 40 frequency points : A: 790MHz ~ 830MHz & B : 900MHz ~ 940MHz , each frequency point move 1MHz in the screen by pressing vol+/vol- button , adjust the channel only when there is interference.
  6. A total of 10 levels of volume are supported in the UHF microphones , volume level is displayed in the LCD.
  7. One short press the SET key to switch between A/B channels.
  8. Long press the SET key for 2-3 seconds will take the microphone to the PAIR mode with the Amplifier XT-160AMP.
  9. Distance between Amplifier and Mic is Not more than 30M.

Pairing Steps:

  1. When the device is powered on, long press the MIC button in the remote control for 2 seconds, and the Amplifier will play Sound the “Mic ready for pairing” prompt tone. The Mic Pairing is limited to Max 1 minute. repeat this step if you did not catch the 1 minute.
  2. Long press the microphone SET key 2 seconds for pairing. If the pairing is successful , the Amplifier will play the sound “Mic paired successfully”. If not, press the microphone SET key and try again.
  3. Repeat Step 2 to PAIR the second Mic. using B or A channels.

Please complete the above paired operations within 1 minute. If UHF microphone is not paired for more than 1 minute, the device will not announce “mic paired successfully” Please complete the above paired operations within 1 minute. If UHF microphone is not paired for more than 1 minute, the device will not announce “mic paired successfully”

UHF Clip microphone instructions ( MIC-03 )

XonTel-XT-160AMP-Amplifier-VoIP-PBX-Phone-Systems-fig6 Note : To avoid howling or strong echo sound between Clip Mic and the Amplifier please Clip Mic must be at least 6M away from the Amplifier when using it.

  1. The Microphone pickup is inserted into the Microphone interface.
  2. Turn the POWER/VOL knob to turn on the UHF microphone and adjust the microphone volume. The POWER LED and display light up.
  3. UHF microphone display screen displays microphone battery power, working channel.
  4. If the UHF microphone display screen does not operate within 5 seconds, it will automatically turn off. Moving the sound volume switch/Power will wake up the screen displayed again.
  5. UHF microphones are set with 40 frequency points, A: 790MHz ~ 830MHz, B: 900MHz ~ 940MHz, each frequency point interval is 1MHz. When the display is on, press CH+/CH- button to adjust the UHF microphone working channel – usually adjust the channel when there is interference.
  6. A total of 10 levels of volume are set for UHF microphones, rotating VOL adjusts the microphone volume and displays the volume level on the display.
  7. Hold down the CH- key for 2 seconds to switch the A/B channel of the microphone. The setting takes effect after that the microphone is restarted.
  8. Hold down the CH+ key for 2 seconds to control the microphone to enter the pairing mode,and then pair the microphone with the XT-160AMP for the pairing mode within 5 seconds.
  9. Distance between Amplifier and Mic is Not more than 30M.

Important Questions

Can I connect ( PAIR ) One Mic into two Amplifiers ?
Yes you can , Just do the Pair to the two Amplifiers with the Mic at the same time , meaning Press the Mic button for the two amplifiers to get into the Pair Mode both during the first 60sec(1Min).then do the Mic PAIR .

Some of my remote control buttons not working well?
Do the Pair step again for the Remote Control .

Can I Play Music from my Mobile to Multiple XonTel Amplifiers at the same time?
Yes you can , but Unfortunately this feature is working only with all Android Mobiles , while Apple Company limited this feature ( Audio Sharing ) for only their headphones and earbuds.
USB upgrading firmware steps:
Put the firmware on the USB flash drive, plug the USB flash drive to USB line, and then connect the XT-160AMP Upgrading port, Prompt tone: “Upgrading firmware, pls wait’’ will be played, and when it is done, broadcast: Firmware upgrading completed. If fail, will broadcast: Firmware upgrade failed.
Note : you must use any MP3 file inside same USB Flash along with the FW file

XonTel-XT-160AMP-Amplifier-VoIP-PBX-Phone-Systems-fig7

1880005
www.xontel.com
kuwait@xontel.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals