KLOCK FXRP Style Fairing For Fxr Style Fairing Kit Installation Guide

: June 13, 2024
: KLOCK

Table of Contents

INSTRUCTIONS
INSTRUCTIONS CONTINUED
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KLOCK FXRP Style Fairing For Fxr Style Fairing Kit Installation Guide

INSTRUCTIONS

FXRP STYLE FAIRING

TOOLS NEEDED

Ratchet
4” Extension
7/16” Socket
7/16” Wrench
9/16” Socket
9/16” Wrench
3/16” Hex Bit Socket
Torque Wrench
Fender Cover/Towel
1/2” Wrench
1/2” Socket
1/4” Hex Bit Socket

We highly recommend a complete installation for test fit prior to paint. The test fit is also important to test for handlebar clearance that may need to be adjusted or replaced.

Verify all the contents of the Fairing Fit Kit (FIG 1):

a. Fairing
b. Neck Bracket
c. Lower Support
d. Fairing Mount Adapter
e. 7” Headlight Mount Ring
f. Hardware Kit

Hardware Bag “B” – Windshield
Hardware Bag “C” – 7” Headlight Ring Mount
Hardware Bag “D” – Fairing to Neck
Hardware Bag “E” – Lower Support to Fairing
Hardware Bag “F” – Neck to Frame
Hardware Bag “G” – Lower Support to Frame

g. Headlight Cover Kit

Headlight Cover
Headlight Cover Trim
Headlight Cover Hardware
Headlight Cover Instructions

h. FXRP 9” Dark Smoke Flare™ Windshield

INSTRUCTIONS CONTINUED

Cover the front fender to help protect against damage (FIG 2).

Disconnect negative battery cable.

Remove windshield and fairing if equipped.

Remove headlight and mount (FIG 3).
Instructions Continued

Locate mounting holes in the frame and remove black plastic plugs (FIG 4). If threaded holes need cleaned out, the thread pitch is 5/16”-18.
Instructions Continued

Using Hardware Bag “F” install the Neck Bracket onto frame (FIG 5). Lightly snug bolts down, still allowing for adjustment.
Instructions Continued

Using Hardware Bag “D” install Fairing (FIG 6) and Fairing Mount Adapter to the Neck Bracket (FIG 7). Position the Fairing Mount Adapter (FIG 8) so the notch is at the 6 o’clock down position. Snug bolts down, still allowing for side-to-side adjustments.
Instructions Continued

Locate Lower Support mounting hole in the frame (FIG 9). If threaded hole needs to be cleaned out, the thread pitch is 3/8-16. Using Hardware Bag “E” &”G” install the Lower Support. The mounting plates should be inside the fairing, not underneath (FIG 10)

Tighten all loosely installed hardware in order of torque values listed:

a. Hardware Bag “G” – 3/8” Hardware – Lower Support to Frame – 18 ft-lbs.
b. Hardware Bag “E” – 1/4” Hardware – Lower Support to Fairing – 45 in- lbs.
c. Hardware Bag “D” – 3/8” Hardware – Fairing to Neck – 18 ft-lbs.
d. Hardware Bag “F” – 5/16” Hardware – Neck to Frame – 13 ft-lbs.

Using Hardware Bag “C” install 7” Headlight Ring Mount to Fairing Mount Adapter positioning the threaded tab at 6 o’clock down and torqueing to 45 in- lbs (FIG 11). If not using a trim ring, remove screw from threaded tab.
Locate Lower

Remove the headlight retaining ring (FIG 12), install the headlight, and reinstall the retaining ring (FIG 13).
Using Hardware

NOTE: Headlight adjustment screws with springs may require thread locking compound after adjustments are made.

Using Hardware Bag “B” insert the seven well nuts into the fairing (FIG 14) and install your new Flare™ Windshield, torquing screws to 10 in-lbs (FIG 15).
Windshield Torquing