CRAFT MAIN MRRL4876-CL-BN Marina Frameless Brushed Nickel Roller Shower Door Instruction Manual
- June 13, 2024
- CRAFT MAIN
Table of Contents
CRAFT MAIN MRRL4876-CL-BN Marina Frameless Brushed Nickel Roller Shower
Door
Product Information
The MARINATM ROLLER is a product manufactured by TM SHOWER & TUB DOOR. It is designed to be used as a roller for shower and tub doors. The product comes with various parts that are necessary for installation.
Parts List:
- Flat Head Screw
- Flat Head Screw
Recommended Tools:
- Silicone
- Drill
- Tape Measure
- Rubber Mallet
- 1/4 (6mm) Drill Bits
- 3/16 (8mm) Drill Bits
- Knife
- Level
- Pencil
- Screwdrivers
- Hex Keys
Important Note:
This door requires a 3 wide flat surface for proper installation.
Safety Warning:
Safety glasses should always be worn when working with tempered glass.
Product Usage Instructions
-
Step 1: Choose the Shower Door Open Direction – Left or Right Shower Door
Follow the appropriate diagram below to determine the assembly for the left or right-hand shower door. -
Step 2: Install Rollers to Door Panel
Pick up the rollers from the package and install them to the door panel using a 4mm hex key. -
Step 3: Put the Door Panel Inside the Shower
Place the door panel inside your shower and set wood blocks under the bottom of the panel for support. -
Step 4: Determine Wall Bracket Placement
Use a professional level and the provided cardboard positioner to determine the position of both the right and left wall brackets. Mark the placement using the bottom hole only. The wall bracket should be mounted as close to the outside of the shower base threshold as possible. -
Step 5: Mark and Drill Hole
Mark and drill holes for the wall channel using a 1/4 (6mm) drill bit. Drill holes for the wall bracket using a 5/16 (8mm) drill bit. -
Step 6: Install Wall Plugs and Wall Channel
Install the wall plugs and then fasten the wall channel using ST3.5×35 flathead screws according to the holes drilled in the previous step.
Note : The installation process continues with additional steps, but they are not included in the provided text extract. Please refer to the complete user manual for detailed instructions on completing the installation.
READ THE INSTRUCTIONS CAREFULLY
Familiarize yourself with all the parts as shown in the exploded view. The
exploded view will also provide a helpful reference when relating to the
location of the various parts and how they are mounted.
PRODUCT OVERVIEW
PARTS LIST
RECOMMENDED TOOLS
WARNING : Safety glasses should always be worn when working with tempered glass.
BEFORE YOU BEGIN
- CAUTION : Risk of injury or product damage. Unframed tempered glass should not contact with hard surfaces or it may shatter. Do not touch the edge of the tempered glass panel with tools or any hard objects. Do not set the unframed tempered glass edge directly on the floor.
- CAUTION : Risk of injury or product damage. Do not attempt to cut tempered glass. Tempered glass shatters when it is cut.
- CAUTION : Risk of product damage and property damage. This shower door is very heavy, Do not install it to plastic shower modules or drywall unless additional support is provided behind the wall.
IMPORTANT NOTE : This door requires a 3″ wide flat surface for proper installation.
- Before starting the installation, layout and identify all of the parts. Inspect them for damage.
- Closely follow the instructions about the sealant application on the door. Sealing areas other than those shown may cause leakage.
- Two people should perform this installation.
CHOOSE THE SHOWER DOOR OPEN DIRECTION
LEFT OR RIGHT SHOWER DOOR
FOLLOW THE APPROPRIATE DIAGRAM BELOW
INSTALLATION PROCEDURE
-
STEP 1
Install rollers to the door. Pick up the rollers from the package, and install them to the door panel as illustrated, fastened by a hex key 4mm. -
STEP 2
Put the door panel inside your shower and have the wood blocks set under the bottom of the panel as illustrated. -
STEP 3
Use a professional level and the provided cardboard positioner for this step. Before installing the wall channel, determine the position of both (right and left) wall brackets. Use the bottom hole only to mark the wall bracket placement. (Approx. 73). You need 3 of base width to mount the bottom rail to the shower base (see page 11). Mount as close to the outside of the shower base threshold as possible. -
STEP 4
Mark and drill holes for the wall channel with a 1/4″ (6mm) drill bit. Drill holes for the wall bracket with a 5/16″ (8mm) drill bit. -
STEP 5
Install the wall plugs. -
STEP 6
-
Install the wall channel. Fasten the wall channel according to the holes from the above steps with ST3.5×35 flat-head screws.
- Install the wall bracket. The wall bracket has two parts, take out the inner part of the bracket base as the pics show. The bracket base will slip down on the single mounting screw. Once you have the height determined (the gap at the bottom of the door has to be big enough to slide easily through the bottom guide) take it all apart and mix up the epoxy putty and push some in the slotted hole above the screw head on both bracket bases.
- The bracket base mounting hole can slip. Epoxy or shim might be necessary.
-
STEP 7
Measure and cut the bottom track. Measure from wall to wall channel at the bottom. Mark the bottom track at the determined distance, and cut from the end. Smooth the rough edges (avoid damaging finished surfaces). Install the bottom track. -
STEP 8
Drill holes for the bottom track with a 1/4”(6mm) drill bit. -
STEP 9
Install the wall plugs (16). -
STEP 10
Install the bottom track.- Fasten the bottom track according to the holes with ST3.5×35 flat head screws.
-
STEP 11
Use a caulk gun to inject clear silicone sealant into the wall channel and bottom track. STEP 12
Install the fixed panel. Put the fixed panel into the bottom track and the wall channel. -
STEP 13
Measure and cut the running rail. Measure from wall to wall at the top of the shower door opening. Mark the running rail at the determined distance and cut. Smooth the rough edges where the running rail was cut. Take care to avoid damaging finished surfaces. Install running rail.
NOTE : Recommend bi-metal hacksaw/reciprocating/bandsaw blade to cut the stainless steel header. -
STEP 14
Prepare the running rail. Position the stoppers on the running rail. Secure them temporarily in place, pointing upright. Take the glass holders apart using the install rod. Place the outer part of the wall bracket onto the running rail. -
STEP 15
Mount the running rail. Fasten the running rail to the fixed panel with the glass holders. Then, fasten the outer parts of the wall brackets to the wall bracket bases. Tighten all hex screws for the wall brackets. -
STEP 16
Install the bottom guide. Use a positioner to determine the bottom guide’s position as illustrated (1). Drill holes with an 8mm drill bit as illustrated (2). Fasten the bottom guide according to the holes from the above steps by wall plugs and ST4.8×38 flat head screws, as illustrated (3) & (4).- Check the bottom guide. Put the black rubber in the 10mm position. This bottom guide fits for 3 different thicknesses. Secure the thickness for 10mm glass. Fasten the bottom guide as illustrated.
-
STEP 17
Install the door panel. Install sliding door ensuring that rollers are fixed over the running rail. Ensure that the sliding door is placed within the bottom guide. -
STEP 18
Install the handle as illustrated.- Install the door gasket and gap gaskets. Install the door gasket on the wall side. Install another gap gasket on the other side of the glass door. Install a gap gasket to the fixed panel.
- Install the glass fix nails as illustrated
- Measure and cut the bottom track cover. Measure from the wall to a fixed panel at the bottom track. Mark the bottom track cover at the determined distance and cut. Smooth the rough edges where the bottom track cover was cut. Take care to avoid damaging finished surfaces.
- Install the bottom track cover as illustrated.
-
STEP 19
- Adjust the door panel. Using adjustment cams, use a hex key or install a rod to straighten the door panel tightly against the shower wall.
- Fasten the stopper and rollers. Adjust the stoppers so the glass door panel does not contact the shower wall.
- Note : Use the hex key 2.5mm to tighten the roller.
Seal the door assembly.
Apply silicone between the bottom of the fixed panel and the base. Silicone
application along the wall channel is also suggested. In both cases, it is
done from the outside of the shower area.
Keep the entire area dry for a minimum of 24 hours.
ATTENTION CONSUMER:
IMPORTANT SHOWER ENCLOSURE WARRANTY INFORMATION PLEASE DO NOT DISCARD
Thank you for your purchase of a shower door from FGI Industries, Ltd. To be eligible for a product warranty, please register your door on our website within two (2) weeks of installation.
Go to:
https://craftandmain.com/warranty/ and follow the instructions.
For any questions or comments about your new shower door, please contact our Customer Service at:
US CUSTOMERS:
1-888-620-3667 CustomerService.US
@FGI-Industries.com 6241
Northwind Parkway Hobart, IN USA 46342
CANADA CUSTOMERS:
1-888-256-7551 customerservice.cdn
@FGI-Industries.com 5970
Chedworth Way, Unit B Mississauga, Ontario, Canada L5R 4G5
© 2022 FGI Industries, Ltd. | CRAFT + MAIN™, MARINA™, and logo designs are trademarks or registered trademarks of FGI Industries, Ltd.
References
- Craft + Main | Innovation, Quality, and Customer Service
- Home - CRAFT + MAIN
- Warranty - CRAFT + MAIN
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>