CRAFT MAIN COVE Frameless Pivot Shower Door and Panel Instruction Manual

June 12, 2024
CRAFT MAIN

CRAFT MAIN logo FRAMELESS PIVOT SHOWER DOOR AND PANELCRAFT MAIN COVE
Frameless Pivot Shower Door and Panel

CRAFT MAIN COVE Frameless Pivot Shower Door and Panel

COPY THE MODEL NUMBER FOR YOUR RECORDS HERE #

READ THE INSTRUCTIONS CAREFULLY
Familiarize yourself with all the parts as shown in the exploded view. The exploded view will also provide a helpful reference when relating to the location of the various parts and how they are mounted.
Please visit us on YouTube and view our shower door installation videos.
One may be available for your installation. www.youtube.com/c/CRAFTANDMAIN

Toll Free Customer Assistance
Monday-Friday, 7:30 a.m. To 5:00 p.m. CST| 1-888-620-3667
1-888-256-7551| US Customers
Canada Customers
---|---|---
6241 Northwind Parkway, Hobart, IN USA 46342 USA:
www.craftandmain.com| 5970 Chedworth Way, Unit B, Mississauga, Ontario, Canada L5R 4G5
CANADA: www.craftandmain.ca
---|---

CRAFT MAIN COVE Frameless Pivot Shower Door and Panel -
Parts

PARTS LIST

CRAFT MAIN COVE Frameless Pivot Shower Door and Panel - PARTS
LIST WARNING: Safety glasses should always be worn when working with tempered glass.

RECOMMENDED TOOLS

CRAFT MAIN COVE Frameless Pivot Shower Door and Panel -
TOOLS

INSTALLATION PROCEDURE

STEP 1 / STEP 2 / STEP 3

  1. Set the level on the walls to ensure that they are plum. Then set the wall jambs (14) in place and mark the hole locations.

  2. Next drill holes in the wall and using a rubber mallet, insert the wall plugs (1). 2.1 FOR ACRYLIC & FIBERGLASS SHOWER ENCLOSURES
    Using a 1/8 inch drill bit, drill a hole about 1-1/2 inch deep at each of the previously marked locations.
    WARNING: Do not use wall anchors with fiberglass or acrylic shower enclosures.
    2.2 FOR TILED SHOWER ENCLOSURES
    Using a 1/4 inch masonry drill bit, drill a hole about 1-1/2 inch deep at each of the previously marked locations. Insert wall plug (1) into each of the drilled holes.

  3. Set wall jambs (14) in place and screw (2) into the walls.
    CRAFT MAIN COVE Frameless Pivot Shower Door and Panel - STEP
3 STEP 4 / STEP 5

  4. Connect magnetic wall jamb (13) to the top and bottom track (15) with aluminum gasket (7) and 1″ pan head screws (6). Screws get attached from the back side of the jamb into the top and bottom.
    CRAFT MAIN COVE Frameless Pivot Shower Door and Panel - STEP
4

  5. Insert frame ends into the top and bottom opening of fixed panel (16) and slide until entire assembly is roughly 4″ narrower than overall opening width.
    CRAFT MAIN COVE Frameless Pivot Shower Door and Panel - STEP
5 STEP 6

  6. Lift entire frame assembly into opening and push ends outward to engage wall jambs.
    Use 3/8″ screw (4) on top and bottom frame to lock assembly in place.CRAFT
MAIN COVE Frameless Pivot Shower Door and Panel - STEP 6 STEP 7 / STEP 8
    CRAFT MAIN COVE Frameless Pivot Shower Door and Panel - STEP 7
8

  7. Insert pivots (8) over the glass and screw together. Set pivot washer (19) over pivot pin on top of pivot block. Carefully lower door panel (17) on to pivot block (18) inserting pivot pin into corresponding hole in pivot (8). Slide decorative covers over both  faces of pivots (8).

  8. Tilt door panel (17) slightly into the shower. Set pivot washer (19) over pivot block (18) pin and insert pin into top of pivot (8). Tilt door panel back up and attach pivot block (21) to top frame (15) with 5/8″ screws (5). Adjust any gaps by sliding top and  bottom pivot block (8) and re-tightening mounting screws. Then affix the stopper (22) to top pivot block (21) with 5/16″ screw (23). Install handle and knob.
    STEP 9

  9. Attach magnetic door plastic (10) to outside of glass door panel (17).
    Next, attach pivot side splash guard (11) to opposite end of glass and sweep (12) on the bottom.
    CRAFT MAIN COVE Frameless Pivot Shower Door and Panel - STEP
9 STEP 10

  10. Make adjustments to fit opening.
    Insert 3/8″ screws (4) into the framework and cover screws with caps (3).
    CRAFT MAIN COVE Frameless Pivot Shower Door and Panel - STEP
10 STEP 11

  11. Caulk the inside sides of the shower door frame to seal.
    Keep the entire area dry for a minimum of 24 hours.CRAFT MAIN COVE Frameless
Pivot Shower Door and Panel - STEP 11

CRAFT MAIN logo ATTENTION CONSUMER:

IMPORTANT SHOWER ENCLOSURE WARRANTY INFORMATION PLEASE DO NOT DISCARD

Thank you for your purchase of a shower door from FGI Industries, Ltd.
In order to be eligible for product warranty, please register your door on our website within two (2) weeks of installation.
Go to: https://craftandmain.com/warranty/ and follow the instructions.

For any questions or comments about your new shower door, please contact our Customer Service at:

US CUSTOMERS:
1-888-620-3667
CustomerService.US@FGI-Industries.com| CANADA CUSTOMERS:
1-888-256-7551
customerservice.cdn@FGI-Industries.com
6241 Northwind Parkway
Hobart, IN USA 46342| 5970 Chedworth Way, Unit B
Mississauga, Ontario, Canada L5R 4G5

© 2022 FGI Industries, Ltd. | CRAFT + MAIN™ and logo designs are trademarks or registered trademarks of FGI Industries, Ltd.CRAFT MAIN
logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals