CRAFT MAIN TDSS6070-RN-BN Tides Framed Sliding Shower Door Instruction Manual

June 12, 2024
CRAFT MAIN

CRAFT MAIN logo FRAMED SLIDING
SHOWER & TUB DOOR
Instruction Manual
CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower
Door

TDSS6070-RN-BN Tides Framed Sliding Shower Door

COPY THE MODEL NUMBER FOR YOUR RECORDS HERE #

READ THE INSTRUCTIONS CAREFULLY
Familiarize yourself with all the parts as shown in the exploded view. The exploded view will also provide a helpful reference when relating to the location of the various parts and how they are mounted.

Please visit us on YouTube and view our shower door installation videos.
One may be available for your installation. www.youtube.com/c/CRAFTANDMAIN

Toll Free Customer Assistance
Monday-Friday, 7:30 a.m. To 5:00 p.m. CST

1-888-620-3667 US Customers
1-888-256-7551 Canada Customers

6241 Northwind Parkway, Hobart, IN USA 46342 USA: www.craftandmain.com| 5970 Chedworth Way, Unit B, Mississauga, Ontario, Canada L5R 4G5 CANADA: www.craftandmain.ca

© 2022 FGI Industries, Ltd. | CRAFT + MAIN™ and logo designs are trademarks or registered trademarks of FGI Industries, Ltd.

CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door -
Parts

PART LIST

CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door - PART
LIST

WARNING: Safety glasses should always be worn when working with tempered glass.

RECOMMENDED TOOLS

CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door -
TOOLS

INSTALLATION PROCEDURE

STEP 1 / STEP 2

  1. Attach rollers to flange at top of both panels. The outer panel has an offset lip on one side of the bottom frame. This lip is on the outside face of the panel and rollers should be mounted on the same side as the lip. The inner panel has holes drilled on one  side only of the bottom frame. The holes are on the inside face of the panel and the rollers should be mounted on the same side as the holes.
    NOTE: The slots in the top flange are used to fine tune the adjustment of the panel to make up for walls that are slightly out of square or plumb. For best results start with all rollers centered in the slot and then make adjustments as needed.

  2. Remove screws from the end of the towel bar brackets. Assemble towel bar by putting Towel Bar Brackets (6) on either end of the Towel Bar (5) and attaching the entire assembly to the outside face of the outside panel using the towel bar screws. To tighten  the screws, place the Towel Bar Wrench (15) into the small hole in the side of the screw head and turn the wrench to tighten.
    CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door -
wrench STEP 3 / STEP 4

  3. Measure opening on bottom and cut bottom track (2) 1 1/2″ shorter than opening.

  4. Place wall jamb down over bottom track so that the back of the jamb is between the bottom track and the wall. Using a level to insure jamb is plumb, mark hole locations. Remove jamb and drill holes about 1 1/2″ deep at each of the marked locations.
    NOTE: When drilling into ceramic, glass or stone use a 1/4″ (6mm) MASONRY drill bit.
    NOTE: When installing on fiberglass or acrylic use a 1/8″ (3 mm) drill bit and discard the wall plugs. When installing on fiberglass or acrylic the side jambs may need to be filed at the bottom to fit the contour of the unit. CRAFT
MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door -
unitSTEP 5/ STEP 6
    Repeat Step 4 on the other side.

  5. Run a thin bead of silicone caulk down the entire length of both bottom ledges on the bottom track.
    Place the bottom track into position and press down firmly along the length of the track
    STEP 7 / STEP 8

  6. Push wall plugs into holes drilled in Step 3 and tap them in with a rubber mallet.
    NOTE: If you are installing on fiberglass or acrylic, skip this step and discard the wall plugs.

  7. Dab silicon into all 3 holes on each side and run a bead down the edges of each jamb where it will contact the wall. Use 1 1/2″ pan head screws to attach wall jamb to wall in top and bottom holes only on both sides. The center hole will be addressed in the  next step.
    CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door - next
step STEP 9 / STEP 10/ STEP 11

  8. Run 1 1/2″ pan head screws through wall bumper and then drive it into center hole on each side.

  9. Measure opening at top of wall jamb, cut top track (1) 1/16″ shorter than opening.

  10. Place top track down over wall jambs as shown.
    CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door -
wall STEP 12

  11. Install outer door panel by lifting it up and into top track. When properly installed the roller will rest on the outer rail on the inside of the top track (see inset drawing) and the outer lip of the bottom frame will ride along the raised outer leg of bottom track.
    CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door -
bottom STEP 13 / STEP 14

  12. Install inner door panel by lifting it up and into top track so that roller rests on the inner rail inside the top track (see inset drawing).

  13. Attach the knob to the end of the inside panel that is furthest from the shower head.
    CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door -
head STEP 15

  14. Hook lip of bottom guide into slot in bottom track and screw it to inside door bottom using 3/8″ pan head screws.
    NOTE: This system works best if there is a small amount of play between the guide and panel.
    We suggest that you tighten the screws down completely and then back them off 1/4 turn.
    Slide the door panel from end to end of the track.
    If it feels loose and sloppy, tighten down a bit more. If the panel does not slide smoothly along the entire track, back them off a bit more.
    CRAFT MAIN TDSS6070 RN BN Tides Framed Sliding Shower Door - head
screws FINAL STEP:
    Caulk both sides of the shower door frame to seal.
    Keep the entire area dry for a minimum of 24 hours.

CRAFT MAIN logo ATTENTION CONSUMER:

IMPORTANT SHOWER ENCLOSURE WARRANTY INFORMATION PLEASE DO NOT DISCARD
Thank you for your purchase of a shower door from FGI Industries, Ltd.
In order to be eligible for product warranty, please register your door on our website within two (2) weeks of installation.
Go to: https://craftandmain.com/warranty/ and follow the instructions.

For any questions or comments about your new shower door, please contact our Customer Service at:

US CUSTOMERS:
1-888-620-3667
CustomerService.US@FGI-Industries.com| CANADA CUSTOMERS:
1-888-256-7551
customerservice.cdn@FGI-Industries.com
---|---
6241 Northwind Parkway
Hobart, IN USA 46342| 5970 Chedworth Way, Unit B
Mississauga, Ontario, Canada L5R 4G5

CRAFT MAIN logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals