TEKA GFG2 INOX Built In Cooker Hood User Manual

TEKA GFG2 INOX Built In Cooker Hood

Product Information

The GFG2 INOX is a user-friendly device designed to provide effective ventilation in your kitchen. It comes with a variety of features that enhance its functionality and performance. The device is equipped with a motor switch that allows you to select from 3 different speeds or turn off the motor completely. It also has a separate light switch for convenient operation. The LED lamp provides excellent illumination while cooking. The device includes a frame and filter holder that control the functions of the hood. The filters can be easily cleaned for optimal performance. The device meets all necessary electrical requirements and is designed to ensure safety during use.

Product Usage Instructions

1. Before using the device for the first time, carefully read the
   installation and maintenance instructions provided in the user manual.

2. Ensure that the device is properly installed according to the instructions provided.

3. To operate the device, use the motor switch to select the desired speed or turn off the motor.

4. Use the light switch to control the illumination of the LED lamp.

5. Regularly clean the filters to maintain optimal performance. Follow the safety instructions provided for cleaning and maintenance tasks.

6. In case of any issues, refer to the troubleshooting section in the user manual. Contact the installer or customer service if necessary.

7. To save energy, let the device run for a few minutes after cooking to dry out any moisture. Use higher speeds only when needed to avoid excessive power consumption.

8. If you need to remove the device for cleaning or disposal, follow the instructions provided in the user manual. Adhere to the relevant environmental guidelines for waste disposal.

9. As an end user, it is your responsibility to properly dispose of all components and old batteries in accordance with recycling guidelines. Protect personal data before disposing of the device.

Safety Instructions

Carefully read the instructions before installing and using the equipment. The manufacturer is not liable for improper installation and use of the equipment that may cause injuries and damage. Always keep the instructions at hand, so they can be easily referred to during use.

Children and Vulnerable people’s safety

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they are supervised by an adult or a person who is responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be done by children without supervision.

General Safety

• There shall be adequate ventilation in the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• Do not flambé food under the range hood.
• CAUTION : Accessible parts may become hot when used with cooking appliances.

Installation

• The installation instructions are defined on the images at the beginning of this user manual.
• First, remove the protective foil from the back of the appliance and, following installation, remove the foil completely.
• The electrical installation is to be set up so that the appliance can be isolated from the mains with a minimum 3mm all-pole contact separation. Suitable separation devices include e.g. cutouts, CD’s and contactors.
• This installation must comply with current regulations.
• If the electrical connection is done through a plug and this remains accessible after installation, then it is not necessary to provide the mentioned separation device.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• The lower part of the extractor must be located at a minimum height of 50 cm above the hob for electric cookers and 65 cm for gas cookers. If the instructions of a gas cooker indicate a greater distance these must be observed.
• Before installing the extractor consult the local rules and regulations in force with respect to the discharge of air and fumes.
• When the extractor is working at the same time as other non-electrical cooking equipment, the outlet air pressure must not exceed 4 Pa (4×10-5 bar).
• Before connecting the extractor to the mains, check that both the voltage and the frequency conform to that shown on the characteristics label located inside the extractor.
• To achieve optimum performance the length of the outlet hose should not exceed 4 meters or include more than two 90º angles (elbows).
• Although venting to the outside is recommended, an activated carbon filter may be used to allow the gas to be returned to the kitchen through the outlet pipe.

Cleaning

• There is a fire risk if cleaning is not carried out in accordance with the instructions.
• Do not allow grease to accumulate in any part of the extractor, especially in the grease filters as this COULD PRODUCE A FIRE RISK!
• The grease filters and the internal part of the extractor must be cleaned at least once a month depending on how often the extractor is used. Note that grease is deposited in the extractor when cooking, whether it is switched on or not.
• We recommend the use of gloves and caution when cleaning the inside of the extractor.

Repairs

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Do not switch on the extractor if the supply cord is worn or has cuts or if there are signs of deterioration around the control panel.
• If the LED module is malfunctioning, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• If the extractor stops working or functions abnormally, unplug it from the mains and contact the technical service.
• Please contact the nearest Qualified Technical Assistance Service for any repairs always using original spare parts. Repairs and modifications carried out by others could damage the extractor or cause it to malfunction and cause safety risks.

Description of the appliance (Fia. 1-3)

• A Motor controls, three speeds:
• B Light switch independent from motor commands
• C Lighting by means of LED lamp
• D Filter located over cooking area, easily withdrawn for cleaning
• E Frame and filter support
• F Possibility of incorporating activated charcoal filter (fig.2)
• G -H Anti return tabs are to be located in the outlet mouth, locating their ends in the holes provided (fig.2).

Instructions for use

• By pressing the buttons (“A”, and “B”) shown in Figure 1, you will be able to control the functions of the extractor.
• To achieve better extraction, we recommend switching on the extractor a few minutes before starting to cook (3 – 5 minutes) so that the airflow is continuous and stable when extracting the fumes.
• Likewise, keep the extractor switched on for a few minutes when cooking is complete to allow all fumes and odors to be expelled.

Cleaning and maintenance

Before carrying out any cleaning or maintenance activities, ensure that the extractor is disconnected from the mains.
To carry out cleaning and maintenance, follow the Safety Instructions.
Fire risk exists in case cleaning does not take place according to the instructions.

Filter cleaning

To withdraw the filters from their locations release the anchoring points. Clean the filter, either by putting it in the dishwasher (see notes) or leaving it standing in hot water to simplify the removal of grease or, if wished, by means of special sprays (protecting the nonmetallic parts). Once clean, leave it to dry.
To replace the filters, proceed in the reverse way to their removal. Make sure that the filter latch is securely attached to the housing to prevent untimely drops of the filters.

• Attention: the cooker hood will not work until the main filter was reinstalled.
• Notes: cleaning in the dishwasher with aggressive detergents may blacken the surface of metallic parts, without this affecting its gas retaining properties.
• N.B. The filter must be cleaned at least once a month depending on how often the extractor is used. It must be remembered that grease is deposited in the extractor when cooking, whether it is switched on or not.

Cleaning of the extractor body

The use of warm (40ºC approx.) soapy water is recommended. A cloth moistened in this water is used for cleaning the extractor, paying special attention to the grids. Afterwards, dry it using a lint-free cloth.

Note

• Never use metallic scouring pads or abrasive products that could damage the surface.
• Do not use scrapers with metallic surfaces such as knives, scissors, etc.

Activated charcoal filter

• To install the charcoal filter, disassemble the lid, introduce the filter in the position provided and reassemble the lid.
• The carbon filter lasts from three to six months depending on the particular conditions of use.
• The activated carbon filter can neither be washed nor regenerated. Once it is exhausted, it must be changed.
• To replace the exhausted filter with a new one, we will make in the same way that in its assembly, previously extracting the spent filter.
• A reduction in the extraction flow rate may be observed in the hood with the installation of carbon filters.

Technical Information

Electrical characteristics:

• REFER TO THE RATING PLATE

This appliance has been designed, tested and manufactured according to:

• Safety: EN/IEC 60335-1; EN/EC 60335- 2-31, EN/EC 62233.
• Performance : EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO 3741; EN 50564/IEC 62301.
• EMC: EN 55014-1 / CISPR 14-1; EN 55014-2 / CISPR 14-2; EN/IEC 61000-3-2; EN/IEC 61000-3-3.

Installation
In order to fix the cooker hood to the kitchen unit you can choose one of these two possibilities (fig. 3):

• a) To the upper part of the furniture, figure 3 specifies where the position of the holes denominated “A” is indicated. This fixation will be made from the outside using the supplied M6 screws.
• b) To the internal laterals of the furniture through floating holes denominated “B” which exist on each side of the body hood. This fixation will be made from the inside part of the cooker hood, after disassembling the filters.

The lower part of the extractor must be located at a minimum height of 50 cm above the hob for electric cookers and 65 cm for gas cookers. If the instructions of a gas cooker
indicate a greater distance these must be observed. To achieve optimum performance the length of the outlet hose should not exceed 4 meters or include more than two 90° angles (elbows). Although venting to the outside is recommended, activated carbon filters may be used, which allow the gas to be returned to the kitchen through the outlet pipe.

If something does not work
Before seeking technical assistance carry out the following checks first:

The extractor does not work

| The cable is not connected| Connect the mains cable
No current is reaching the

plug

| Revise/repair the electricity circuit

The extractor does not blow enough or vibrates

| Filter saturated with grease| Clean or substitute the filter
Outlet obstructed| Eliminate obstructions
Inadequate air conduit| Contact the installer and follow instructions of this

manual

The lamps do not light| Lamp broken| Contact the Customer Service ILCOS D Code: DSL-12-S-450

DIMENSION

Special U.K. Requirements

• Height above gas hob: 75 mm minimum.
• NEVER PLACE THE COOKER HOOD OVER AN EYE-LEVEL GRILL.
• This appliance must be connected by a competent person, using fixed wiring via a DOUBLE POLE SWITCHED FUSED SPUR OUTLET.

Special Australia Requirements

• This appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.

Electrical connection

• We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations.

• Should the color of the wires in the mains lead for the appliance not correspond with the colored markings identifying the terminal in your spur box proceed as follows:

• The wire which is a colored blur must be connected to the marked N (Neutral) or colored Black.

• The wire which is coloured brown must be connected to the marked L (Live) or colored Red
  Where available (see installation), the wire that is colored yellow/green must be connected to the market ⊥ or colored Yellow/Green.

• If the cooker hood is installed for use above a gas appliance then the provision of ventilation must be in accordance with the Gas Safety (Installation & Use) Regulations 1984 and the relevant Building Regulations. Detailed recommendations are contained in the following British Standard Codes of Practice BS6172, BS5440, and BS6891 Current Edition.

Environmental protection

Saving Energy
This appliance is energy-efficient but there are some tips on how to save even more energy:

• During cooking, ensure that there is a sufficient supply of air to enable the extractor hood to work efficiently and with a low level of operating noise.
• Adjust the fan speed to the amount of steam produced during cooking. Only use intensive mode when required. The lower the fan speed, the less energy is consumed.
• If cooking produces large amounts of steam, select the higher fan speed in good time. If the cooking steam has already spread around the kitchen, the extractor hood will need to be operated for longer thus consuming more energy.
• Switch off the extractor hood if you no longer require it.
• Switch off the lighting if you no longer require it.
• Clean and (if required) replace the filter at regular intervals to increase the effectiveness of the ventilation system and to prevent the risk of fire.
• Put the lid on the pans to reduce cooking steam and condensation.

Disposal of the packaging
The packaging bears the Green Point mark.
Dispose of all the packaging materials such as cardboard, expanded polystyrene, and plastic wrapping in the appropriate bins. In this way, you can be sure that the packaging materials will be re-used.

Dismantling the equipment

1. Disconnect the main power.
2. Remove the duct cover above the hood.
3. Disconnect the duct.
4. Supporting the equipment, remove the srews that fix it to the wall.
5. For waste disposal, proceed according to the appropriate environmental protection guidelines.

Disposal of equipment no longer used

• According to European Directive 2012/19/EU on the management of waste electrical and electronic equipment (WEEE), home electrical appliances should not be put into the normal systems for disposal of solid urban waste.
• Outdated appliances should be collected separately to optimize component material recovery and recycling rates and to prevent potential harm to human health and the environment. The symbol of a rubbish container superimposed by a diagonal cross should be put on all such products to remind people of their obligation to have such items collected separately.
• Consumers should contact their local authorities or point of sale and request information on the appropriate places to leave their old home electrical appliances.
• Before disposing of your appliance, render it non-usable by pulling out the power cable, cutting this, and disposing of it.

www.teka.com

References

• Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.
• Teka | Cook your way to life

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>