Einhell TE-HD 18 20 Li Cordless Hammer Drill Instruction Manual

TE-HD 18 20 Li Cordless Hammer Drill
Instruction Manual

Danger! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 11)

1. Danger! – Read the operating instructions to reduce the risk of injury.
2.  Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!
4. Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
5. Select between the individual functions only when the equipment is at a standstill. If you fail to observe this point, the equipment may be damaged.
6.  Turn and push the SDS-Plus drill bit into the tool chuck as far as it will go. The tool will lock automatically.
7. 1. Pull back and hold the locking sleeve! 2. Remove the tool!
8. Store the batteries only in dry rooms with an ambient temperature of +10°C to +40°C. Place only fully charged batteries in storage (charged at least 40%).

Safety regulations

The corresponding safety information can be found in the enclosed booklet.
Warning!
Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fi re and/or serious injury.
Keep all the safety information and instructions in a   safe place for future use.

Layout and items supplied

2.1 Layout (Fig. 1/7)

1. Locking sleeve
2.  Drill/impact drill/chisel selector switch
3. Changeover switch
4.  On/Off switch
5. Battery (not included in delivery)
6. Pushlock button
7.  Battery capacity indicator
8. Charger (not included in delivery)
9.  LED lamp
10.  Additional handle
11.  Depth stop

2.2 Items supplied
Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

• Cordless impact drill
• Additional handle
• Depth stop
• Original operating instructions
• Safety instructions

Proper use

The equipment is designed for drilling work with hammer action in concrete, rock and brick, always using the correct drill bit. The equipment is also suitable for screwdriving and drilling in wood and steel.
The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

Important!
The equipment is supplied without rechargeable batteries and without a charger and is allowed to be used only with the lithium-ion batteries of the Power X-Change series!
The lithium-ion batteries of the Power X-Change series are allowed to be charged only with Power  chargers.
Danger!
Sound and vibration
Sound and vibration values were measured in accordance with EN 62841.

Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) determined in accordance with EN 62841.
Impact drilling in concrete
Vibration emission value ah = 12.604 m/s² K uncertainty = 1.5 m/s²
Chiseling
Vibration emission value ah = 9.335 m/s² K uncertainty = 1.5 m/s²
The specified vibration value was established in accordance with a standardized testing method. It may change according to how the electric equipment is used and may exceed the specified value in exceptional circumstances.
The specified vibration value can be used to compare the equipment with other electric power tools. The specified vibration value can be used for initial assessment of a harmful effect.
Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
•  Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.

Caution!
Residual risks
Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules  out. The  following hazards may arise in connection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.
2.  Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Limit the operating time.
All stages of the operating cycle must be considered (for example, times in which the electric tools are switched off and times in which the tool is switched on but operates without load).

Before using the equipment

Be sure to read the following information before you put the cordless impact drill into operation:

1. Charge the battery pack only with a charger from the Power X-Change series.
2. Only ever use sharp drill bits and screwdriver bits which are suitable for the purpose and in faultless condition.
3. Using a cable/pipe detector, check the area you want to work on for concealed electric cables and gas and water pipes.

5.1 Additional handle (Fig. 2/Item 10)
For safety reasons you must only use the impact drill with the additional handle. The additional handle (10) enables you to achievebetter stability whilst using the impact  drill. For safety reasons the machine must not be used without the additional handle (10). The additional handle (10) is secured to the    impact drill by aclamp. Turning the handle anticlockwise (viewed from the handle) will release the clamp. Turning the handle clockwise tightens the clamp.
Release the clamp of the additional handle first. Then you can swivel the additional handle (10) into the most  comfortable working position for yourself. Now turn the additional handle (10) in the opposite direction again until the additional handle (10) is secure.
5.2 Fitting and adjusting the depth stop (Fig. 3/Item 11)
The depth stop (11) is held in place by the additional handle (10) by clamping. The clamp can be  released and tightened by turning the handle.

• Release the clamp and fit the depth stop (11) in the recess provided for it in the additional handle.
• Set the depth stop (11) to the same level as the drill bit.
• Pull the depth stop back by the required drilling depth.
• Turn the handle on the additional handle (10) until it is secure.
• Now drill the hole until the depth stop (11) touches the workpiece.

5.3 Inserting a tool (Fig. 4)
Important! Set the changeover switch (3) to its center position whenever you carry out any work (for example changing the tool, maintenance work, etc.) on the equipment.

• Clean the tool before fitting it and apply a thin coating of bit grease to the tool shaft.
• Turn and push the dust-free tool into the tool mounting (b) as far as it will go. The tool will lock automatically.
• Check that the bit is locked in placed by pulling on it.

5.4 Removing a tool (Fig. 5)
Pull back and hold the locking sleeve (1) and remove the tool.

Operation

6.1 Charging the LI battery pack (Fig. 6/7)

1. Remove the battery pack (5) from the handle, pressing the push lock button (6) downwards to do so.
2.  Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (8) into the socket outlet. The green LED will then begin to fl ash.
3.  Push the battery pack onto the battery charger. In section 10 (Charger indicator) you will fi nd a table with an explanation of the LED indicator on the charger.

If the battery pack fails to charge, check for the following:

• voltage at the power socket
• whether there is good contact at the charging contacts of the charging unit If the battery pack still fails to charge, send
• the charger and charging adapter
• and the battery pack to our customer service center.

To ensure that items are properly packaged and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased.
When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and fires. To ensure that the battery pack provides long service,
you should take care to recharge it promptly. You must recharge the battery pack when you  notice that the performance of the device drops.  ever allow the battery pack to become fully  discharged. This will cause it to develop a defect.
6.2 Drill / Impact drill / Chisel selector switch (Fig. 8)

• For drilling, press the button (E) on the rotary switch (2) and simultaneously turn the rotary switch (2) to position A.
• For impact drilling, press the button (E) on the rotary switch (2) and simultaneously turn the rotary switch (2) to position B.
• To set the chisel position, press the button (E) on the rotary switch (2) and simultaneously turn the rotary switch (2) to setting C.
• Important! In this setting the chisel does not latch in place!
• In this setting you can turn the chisel by hand into the required position.
• For chiseling, press the button (E) on the rotary switch (2) and simultaneously turn the rotary switch (2) to position D.
• The chisel is locked in position D.

Important!
You need apply only slight contact pressure for impact drilling. Excessive contact pressure will place unnecessary strain on the motor. Check drill bits at regular intervals. Sharpen or replace blunt drill bits.
6.3 Changeover switch (Fig. 9)
Using the changeover switch (3) above the On/ Off switch (4) you can select the direction of rotation of the equipment and lock the equipment so that it cannot be switched on accidentally. You can select between clockwise and counter-clockwise rotation.
To avoid causing damage to the gearing, the direction of rotation must only be changed when the equipment is at a standstill. When the changeover switch (3) is in the middle position, the On/Off switch (4) is blocked.
Danger!
To avoid danger, the machine must only be held using the two handles.
Otherwise you may suffer an electric shock if you drill into electric cables!
6.4 On/Off switch (Fig. 9)
Infinitely variable speed control is possible with the On/Off switch (4). The further you push the switch, the higher the speed of the equipment.
Switching on:
Press the On/Off switch (4).
Switching off :
Release the On/Off switch (4).
6.5 Battery capacity indicator (Fig. 10)
Press the button for the battery capacity indicator (d). The battery capacity indicator (7) shows the charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the battery from the equipment, keep it at room temperature for one day. If the fault reoccurs, this means that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective  battery.
6.6 LED light (Fig. 1)
The LED light (9) can be used in poor lighting conditions to illuminate the area where you want to drill or screw. The LED light (9) will come on automatically as soon as you press the On/Off switch (4).

Cleaning, maintenance and ordering of spare parts

Danger!
Always pull out the mains power plug before starting any cleaning work.
7.1 Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

7.2 Maintenance
There are no parts inside the equipment which require additional maintenance.
7.3 Ordering spare parts and accessories
Please provide the following information when ordering spare parts:

•  Type of unit
• Article number of the unit
• ID number of the unit
• Spare part number of the required spare part For our latest prices and information please go to www.Einhell-Service.com

Tip! For good results we recommend high-quality accessories from! www.kwb.eu welcome@kwb.eu

http://accessory.kwb.eu/

Charger indicator

The charger is connected to the mains and is ready for use- there is no battery pack in the charger
On| Off| Charging
The charger is charging the battery pack in quick charge mode. The charging times are shown directly on the charger.
Important! The actual charging times may vary slightly from the stated charging times depending on the existing battery charge.
Off| On| The battery Is charged and ready for use. (READY TO GO)
The unit then changes over to gentle charging mode until the battery is fully charged.
To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.
Action:
Take the battery pack out of the charger. Disconnect the charger from the mains supply.
Flashing| Off| Adapted charging
The charger is in gentle charging mode.
For safety reasons the charging is performed less quickly and takes more time. The reasons can be:
– The rechargeable battery has not been used for a very long time. – The battery temperature is outside the ideal range.
Action:
Wait for the charging to be completed; you can still continue to charge the battery pack.
Flashing| Flashing| Fault
Charging is no longer possible. The battery pack is defective. Action:
Never charge a defective battery pack.
Take the battery pack out of the charger.
On| On| Temperature fault
The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C).
Action:
Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .

For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.
The old equipment can be returned to a suitable collection point that will dispose of the equipment in  accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment.
Please note that batteries and lamps (e.g. light bulbs) must be removed from the tool before it is disposed of.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.
Subject to technical changes
Service information
We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

• Not necessarily included in the scope of delivery !
  In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
  Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

  • Did the equipment work at all or was it defective from the beginning?
  • Did you notice anything (symptom or defect) prior to the failure?
  • What malfunction does the equipment have in your opinion (main symptom)?
    Describe this malfunction.

Warranty certificate

Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aff ected by this guarantee. Our guarantee is free of charge to you.
2.  The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee: – Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance. – Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it). – Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used.
5. To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi cation will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.

Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.
Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.
Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article
*Akkus  Bohrhammer TE-DH 18/20 Li (Einhell)
**

• 2014/29/EU

• 2005/32/EC_2009/125/EC

• (EU)2015/1188

• 2014/35/EU

• 2006/28/EC

• 2014/30/EU

• 2014/32/EU

• 2014/53/EU

• 2014/68/EU

• (EU)2016/426

• Notified Body:

• (EU)2016/425

• 2011/65/EU_(EU)2015/863

• 2006/42/EC

• Annex IV
  Notifi ed Body:
  Reg. No.:

• 2 000/14/EC_2005/88/EC
  Annex V
  Annex VI
  Noise: measured LWA = dB (A); guaranteed LWA = dB (A) P = kW; L/Ø = cm Notified Body:

• 2012/46/EU_(EU)2016/1628
  Emission No.:

Standard References: EN 62841-1; EN IEC 62841-2-6; EN IEC 55014-1; EN IEC 55014-2
ISC GmbH · Eschenstra 6 · D-94405 Landau/Iskar
Landau/Isar, den 26.07.2022 First CE : 2022
Art.-No.: 45.142.60
I.-No.: 21012
Subject to change without notice
Archive-File/Record: NAPR023144, Documents registrar: Egginger Christoph Wiesenweg 22, D-94405 Landau/Isar
Cordless hammer drill
Declaration of conformity
We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB,
United Kingdom
declare the conformity to UK standards and legislation was assessed for:
Cordless Rotary Hammer TE-HD 18/20 Li (Einhell)
UK legislation

• Simple Pressure Vessels (Safety) Regulation

• Electrical Equipment (Safety) Regulation

• Radio Equipment Regulation

• Personal Protective Equipment Regulation

• The Ecodesign for Energy-Related Products and Energy Information Regulation

• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation

• Noise Emission in the Environment by Equipment for use Outdoors Regulation
  Annex V
  Annex VI

• Noise: measured LWA = dB (A); guaranteed LWA = dB (A) P = kW; L/Ø = 36 cm UK Approved Body:

• X Supply of Machinery (Safety) Regulation
  Annex IV

• UK Approved Body:

• UKTE Certifi cate No.:

•  Electromagnetic Compatibility Regulation

• Measuring Instruments Regulation

• Pressure Equipment (Safety) Regulation

Standards: BS 62841-1; BS EN IEC 62841-2-6; BS EN IEC 55014-1; BS EN IEC 55014-2
Wirral, 2022.07.26 Article Number: 45.142.60 I.-No.: 21012 Subject to change without notice
Archive-File/Record: NAPR023144 Documents registrar: Egging Christoph Wiesenweg 22, 94405 Landau/Iskar, Germany

Einhell Service
Eschenstra 6
94405 Landau an der Isar
Telefon: 09951 – 959 2000
Telefax: 09951 – 959 1700
E-Mail: Service-DE@Einhell.com
Einhell-Service.com

References

• Einhell Service
• VICE - VICE is the definitive guide to enlightening information.
• Einhell Service
• kwb Germany GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>