dahua VDA-IPCHDBW3441FPASM0280B Vandal Proof Wedge Wedge Dome Network Camera User Guide

dahua VDA-IPCHDBW3441FPASM0280B Vandal Proof Wedge Wedge Dome Network

Camera

Safety Instructions

The following categorized signal words with defined meanings might appear in the manual.

result in slight or moderate injury.
| Indicates a potential risk that, if not avoided, may result in

property damage, data loss, lower performance, or unpredictable result.

| Provides additional information as the emphasis and supplement to the text.

Revision History

About the Manual

• The manual is for reference only. If there is an inconsistency between the manual and the actual product, the actual product shall prevail.
• We are not liable for any loss caused by the operations that do not comply with the
• The manual would be updated according to the latest laws and regulations of related For detailed information, see the paper manual, CD-ROM, QR code, or our official website. If there is an inconsistency between the paper manual and the electronic version, the electronic version shall prevail.
• All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the manual. Please contact customer service for the latest program and supplementary documentation.
• There still might be deviations in technical data, functions, and operations description, or errors in print. If there is any doubt or dispute, please refer to our final explanation.
• Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened.
• All trademarks, registered trademarks, and the company names in the manual are the properties of their respective owners
• Please visit our website, and contact the supplier or customer service if there is any problem occurred when using the device.

Electrical safety

• All installation and operation should conform to your local electrical safety
• The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to the Limited Power Source requirement according to IEC60950-1. Please note that the power supply requirement is subject to the device label.
• Make sure the power supply is correct before operating the
• A readily accessible disconnect device shall be incorporated in the building installation
• Prevent the power cable from being trampled or pressed, especially the plug, power socket, and junction extruded from the device.

Environment

• Do not aim the device at strong light to focus, such as lamp light and sunlight; otherwise, it might cause over brightness or light marks, which are not the device malfunction, and affect the longevity of Complementary Metal-Oxide Semiconductor (CMOS).
• Do not place the device in a damp or dusty environment, extremely hot or cold temperatures, or locations with strong electromagnetic radiation or unstable lighting.
• Keep the device away from any liquid to avoid damage to the internal
• Keep the indoor device away from rain or dampness to avoid fire or
• Keep sound ventilation to avoid heat
• Transport, use, and store the device within the range of allowed humidity and
• Heavy stress, violent vibration, or water splash are not allowed during transportation, storage and
• Pack the device with standard factory packaging or the equivalent material when transporting the
• Install the device in a location where only the professional staff with relevant knowledge of safety guards and warnings can The accidental injury might happen to the non-professionals who enter the installation area when the device is operating normally.

Operation and Daily Maintenance

• Do not touch the heat dissipation component of the device to avoid
• Carefully follow the instructions in the manual when performing any disassembly operation about the device; otherwise, it might cause water leakage or poor image quality due to unprofessional Please make sure that the gasket ring is flat and properly installed in the groove before installing the cover. Please contact after-sale service for desiccant replacement if there is condensed fog on the lens after unpacking or when the desiccant turns green (Not all models are included with the desiccant).
• It is recommended to use the device together with a lightning arrester to improve the lightning protection effect.
  • Do not touch the image sensor (CMOS) Dust and dirt could be removed with an air blower, or you can wipe the lens gently with a soft cloth that is moistened with alcohol.
  • The device body can be cleaned with a soft dry cloth, which can also be used to remove stubborn stains when moistened with mild To avoid possible damage to device body coating which could cause performance decrease, do not use volatile solvents such as alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive detergent is used.
  • The Dome cover is an optical component, do not touch or wipe the cover with your hands directly during installation or operation. For removing dust, grease, or fingerprints, wipe gently with moisten oil-free cotton with diethyl or moisten the soft cloth. You can also air blower to remove
• It is recommended to connect the grounding hole to the ground to enhance the reliability of the

WARNING

• Please strengthen the protection of network, device data, and personal information by adopting measures that include but are not limited to using strong passwords, modifying passwords regularly, upgrading the firmware to the latest version, and isolating the computer For some devices with old firmware versions, the ONVIF password will not be modified automatically along with the modification of the system password, and you need to upgrade the firmware or manually update the ONVIF password.
• Use standard components or accessories provided by the manufacturer and make sure the device is installed and maintained by professional engineers.
• The surface of the image sensor should not be exposed to laser beam radiation in an environment where a laser beam device is used.
• Do not provide two or more power supply sources for the device unless otherwise specified. A failure to follow this instruction might cause damage to the device.

Introduction

Cable

• Cable types might vary with different devices, and the actual product shall prevail.
• Please waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuits and water damage. For the detailed operation, see the FAQ Manual

For more information about cable ports Cable information

1

|

DC 12V power input

| Inputs DC 12V power. Please be sure to supply power as instructed in the Guide.

Device abnormity or damage could occur if power is not supplied correctly.

2

|

Ethernet port

| Connects to network with a network cable. Provides power to the device with PoE.

PoE is available on a select models.

3

|

Mobile aviation port

| Inputs and outputs network data and supplies PoE

power.

Initializing Device

1. Double-click “ConfigTool.exe” to open the tool.

2. Click The Modify IP interface is displayed.
   Modify IP interface

3. Click the Search setting. The Setting interface is displayed.

4. Enter the start IP and end IP of the network segment in which you want to search devices, and then click OK. All the devices found in the network segment are listed.

5. Select one or several devices whose Status is Uninitialized, and then click Initialize. The Device initialization interface is displayed.

6. Select the devices that need initialization, and then click Initialize. The password setting interface is displayed.
   Password setting interface

7. Set and confirm the password of the devices, and then enter a valid email address. Click Next. The final setting interface is displayed.
   Password can be modified or reset in System Settings.

8. Select the options according to your needs and then click OK. The Initialization interface is displayed after initializing is completed. Click the success icon or the failure icon for the details.

9. Click Finish. The device status in the Modify IP interface (Figure 2-1) turns to Initialized.

Modifying Device IP Address

• You can modify the IP address of one or multiple devices at one time. This section is based on modifying IP addresses in batches.
• Modifying IP addresses in a batch is available only when the corresponding devices have the same login password.

1. Do Step 1 to Step 4 in “2.1 Initializing Device” to search devices in your network segment. After clicking the Search setting, please make sure the username and password are the same as what you set during initialization, otherwise, there will be a “wrong password” notice.

2. Select the devices whose IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed.
   Modify IP address interface

3. Select Static mode and enter start IP, subnet mask, and gateway.

   • IP addresses of multiple devices will be set to the same if you select the Same IP.
   • If a DHCP server is available in the network, devices will automatically obtain IP addresses from the DHCP server when you select DHCP.

4. Click OK.

Logging in to Web Interface

1. Open the IE browser, enter the IP address of the device in the address bar, and press Enter. If the setup wizard is displayed, follow the instructions to finish the settings.
2. Enter your user name and password in the login box, and then click Login.
3. For first-time login, click Click Here to Download Plugin and install the plugin as instructed. The main interface is displayed when the installation is finished

Main interface

Installation

Packing List

• The tool required for the installation such as an electric drill is not provided in the packing.
• The operation manual and related tools are contained in the disk or the QR code, and the actual packing shall prevail.

Dimension

Following figures are for reference only, the actual product shall prevail

Installing Device

Installation Method

Installing SD Card (Optional)

• SD card slot is available on select models.
• Please disconnect the power from the device before installing the SD card.
• Short press the reset button for 1–2 s, press the WPS button on the router, and the device can be connected to the corresponding router within 1 minute (only supported by some models).
• Press the reset button for 10 seconds to reset the device.

Attaching Device

Make sure the mounting surface is strong enough to hold at least three times the device’s weight.

The cable going through the mounting surface

The cable going through the side cable tray

Installing Waterproof Connector

This part is only needed when a waterproof connector comes with the device and the device is used outdoor.

Adjusting Angle

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>