Zhejiang Dahua Vision Technology DH-SD2AY Network PT Camera Web 3.0 User Manual

Step 4 Power off the Device and then restart it, or restart the Device over the network.
Step 5 Check the PC command line. If there is information such as “Reply from 192.168.1.125…”, it
means the configuration succeeds. In this case, you can close the command editor.
Step 6 Enter http:// in the browser address bar to log in.
5.2.2 Port
You can configure the maximum port numbers and values on this page.
Step 1 Select Setting > Network > Port.

Step 2 Configure each port value of the Device.

• Except Max Connection, modifications of other parameters will take effect after restart.
•  0–1024, 1900, 3800, 5000, 5050, 9999, 37776, 37780–37880, 39999, and 42323 are occupied for specific uses.
• It is not recommended to use the default values of other ports during port configuration.
  Table 5-15 Description of port parameter

Max Connection

| The maximum number of users that can log in to the web page of the Device simultaneously. The value ranges from 1 to 10, and it is 10 by default.

TCP Port

| TCP service port. The value is 37777 by default. You can set this parameter as needed.

UDP Port

| User Datagram Protocol port. The value is 37778 by default. You can set this parameter as needed.

HTTP Port

| HTTP communication port. The value is 80 by default. You can set this parameter as needed.

RTSP Port

| Real Time Streaming Protocol port. Keep the default value 554 if it is displayed. If you play live view through Apple’s QuickTime or VLC, the

following format is available. This function is also supported by Blackberry mobile phone.

When the URL format requiring RTSP, you need to specify channel number and bit stream type in the URL, and also username and password if needed.

When playing live view with Blackberry mobile phone, you need to disable the audio, and then set the stream encoding mode to H.264B and resolution to CIF.

URL format example:

http://username:password@ip:port/cam/realmonitor?channel=1&subtype= 0

●      Username: Your username. For example, admin.

●      Password: Your password. For example, admin.

●      IP: Your device IP. For example, 192.168.1.122.

●      Port: Leave it if the value is 554 by default.

●      Channel: Channel number starting from 1. For example, if it is channel 2, then enter channel=2.

●      Subtype: stream type. The main stream is 0 (subtype=0); the sub stream is 1 (subtype=1).

For example, if you require the sub stream of channel 2 from a certain device, then the URL shall be:

rtsp://admin:admin@192.168.1.123:554/cam/realmonitor?channel=2&subt ype=1

If certification is not required, you do not need to specify the username and password. Use the following format:

rtsp://ip:port/cam/realmonitor?channel=1&subtype=0

RTMP

| A network protocol for real-time data communication. The value is 1935 by default. You can enter the value as needed.
Enable RTMP to push audio and video data to the third-party server. Make sure that the address is trusted; otherwise it might cause data leakage.

HTTPS Port

| HTTPS communication port. The value is 443 by default. You can set this parameter as needed.

5000 Port

| The port is disabled by default. If you need to connect the Camera to intelligent transportation box through 5000 port, enable this port.  There might be network risk if the port is enabled. Be cautious.

Step 3 Click Save.
5.2.3 PPPoE
You can enable PPPoE (Point-to-Point Protocol over Ethernet) to establish network connection. In this case, the Device obtains a dynamic IP address. To use this function, you need to obtain the PPPoE username and password from the Internet Service Provider (ISP). Step 1 Select Setting > Network > PPPoE.

Step 2 Select Enable, and then enter PPPoE username and password.
Step 3 Click Save.
Save Succeeded! is displayed, and the obtained IP address of public network is displayed in
real time. You can access the Device through the IP address.

5.2.4 DDNS
Properly configure DDNS, and then the domain name on the DNS server matches your IP address and refresh the matching relation in real time. You can always access your device with the same domain name no matter how much your device IP address changes. Before making any changes, check whether your device supports the DNS server.

• The third party servers might collect your device information if DDNS is enabled.
• Register and log in to the DDNS website, and then you can view the information of all the connected cameras in your account.
  Step 1 Select Setting > Network > DDNS.

Step 2 Select Type, and then configure DDNS parameter.
Table 5-16 Description of DDNS parameter

Server Address

| relationship.

●      CN99 DDNS

Server address: www.3322.org

●      NO-IP DDNS

Server address: dynupdate.no-ip.com

●      Dyndns DDNS

Server address: members.dyndns.org

Domain Name| The domain name you registered on the DDNS website.
Username| Enter the username and password obtained from DDNS service provider. You need to register an account (including username and password) on the website of DDNS service provider.
Password
Interval| The update cycle of the connection between your device and the server, and the time is 10 minutes by default.

Step 3 Click Save.
Open the browser, enter the domain name in the address bar, and then press the Enter key.
The login page is displayed.
5.2.5 SMTP (Email)
After this function is enabled, the device data will be sent to the given server. There is data leakage risk. Think twice before enabling the function.
After you configure SMTP (Email), when alarms, video detection and abnormal events are triggered, an email will be sent to the recipient server through SMTP server. The recipient can log in to the incoming mail server to receive emails.
Step 1 Select Setting > Network > SMTP (Email).

Step 2 Configure SMTP (Email) parameter.
Table 5-17 Description of SMTP (Email) parameter

SMTP Server

| IP address of the outgoing mail server complying with SMTP protocol.| For the detailed configuration, see Table 5-18.

Port

| Port number of the outgoing mail server complying with SMTP protocol. It is 25 by default.
Username| Username of sender mailbox.
Password| Password of sender mailbox.

Anonymity

| For servers supporting anonymous email, you can log in anonymously without entering username, password, and sender information.
Sender| Email address of the sender.
Parameter| Description
---|---
Authenticati on| Select authentication type from None , SSL and TLS. TLS is selected by default.

●      For the detailed configuration, see Table 5-18.

●      There might be risks if you select the authentication type other than TLS. TLS is recommended.

Title| You can enter no more than 63 characters in Chinese, English, and Arabic numerals.
Mail Receiver| Email address of the receiver. Support 3 addresses at most.
Attachment| Select the checkbox to support attachment in the email.
Health Mail| The system sends test mail to check if the connection is successfully configured. Select the Health Mail checkbox and configure the Update Period , and then the system sends test mails according to the defined period.
Test| Test whether the email function is normal. If the configuration is correct, the email address of the receiver will receive the test email. Save the email configuration before running rest.

Table 5-18 Description of common email configuration

●      You need to enable SMTP service in your mailbox.

●      The authentication code is required; either the QQ password or email password is not applicable.

Authentication code is the code you receive when enabling SMTP

service.

TLS| 587

163

|

smtp.163.com

| SSL| 465/994| ●      You need to enable SMTP service in your
TLS| 25
Type| SMTP Server| Authentication| Port| Description
---|---|---|---|---
| |

—

| | mailbox.

●      The authentication code is required; the email password is not applicable.

Authentication code is the code you receive when enabling SMTP

service.

Sina

|

smtp.sina.com

| SSL| 465| You need to enable SMTP service in your mailbox.
—| 25

126

|

smtp.126.com

|

—

|

25

| You need to enable SMTP service in your mailbox.

Step 3 Click Save.
5.2.6 UPnP
After UPnP is enabled, Intranet service and port of the Device will be mapped to Extranet. Think twice before enabling it.
UPnP (Universal Plug and Play) allows you to establish the mapping relationship between Intranet and Extranet. Extranet users can access Intranet device by visiting Extranet IP address. Intranet port is device port and Extranet port is router port. Users can access the Device by accessing Extranet port. When you are not using routers for UPnP, disable UPnP to avoid affecting other functions. Once UPnP is enabled, the Device supports UPnP protocol. In Windows XP or Windows Vista, after  UPnP is enabled, the Device can be automatically searched by Windows network.
Adding UPnP Network Service in Windows System

1. Open Control Panel, and then select Add or Remove Programs.
2. Click Add/Remove Windows Components.
3. Select Network Service from the Windows Components Wizard and click Details button.
4. Select Internet Gateway Device Discovery and Control Client, and UPnP User Interface, and then click OK to start installation.

Configuring UPnP

1. Select Setting > Network > UPnP.

2. Select Enable.

3. Select a mode from the drop-down list.
   There are 2 mapping modes: Custom and Default.
   ● In Custom mode, users can modify the external port.
   ● Select Default, and then the system finishes mapping with unoccupied port automatically. In this case, you do not need to modify mapping relation.

4. Select Start Device Discover.

5.  Click Save.

5.2.7 Bonjour
Introduction
Bonjour is also called zero-configuration networking, which can automatically discover computers, devices and services on IP networks. Bonjour is a protocol of industry standard which allows devices to search and find each other. IP address or DNS server is not required during the process. Enable this function, and the network camera will be automatically detected by the OS and client with Bonjour function. When the network camera is automatically detected by Bonjour, server name you have set will be displayed.

Configuring Bonjour

1. Select Setting > Network > Bonjour.
2. Select Enable, and then set Server Name.
3. Click Save.

Visiting Web Page with Safari Browser
In the OS and clients that support Bonjour, perform the following steps to visit the web page of the Device with Safari browser.

1. Click Show all bookmarks in Safari.
2. The OS or client automatically detects the network cameras with Bonjour enabled in the LAN.
3. Click to visit the corresponding web page.

5.2.8 SNMP
After setting SNMP (Simple Network Management Protocol) and connecting to the Device through certain software (such as MIB Builder and MG-SOFT MIB Browser), you can manage and monitor the Device with the software.
Prerequisites

• Install SNMP monitoring and management tool such as MIB Builder and MG-SOFT MIB Browser.
• Get the MIB file of the matched version from technical support.

Procedure
Step 1 Select Setting > Network > SNMP.

Step 2 Select SNMP version to enable SNMP.

• Select V1, and the system can only process information of V1 version.
• Select V2, and the system can only process information of V2 version.
• Select V3, and then V1 and V2 become unavailable. You can configure username, password and authentication type. It requires corresponding username, password and authentication type to access your device from the server.

Using V1 and V2 might cause data leakage, and V3 is recommended.
In Trap Address, enter the IP address of the PC that has MIB Builder and MG- SOFT MIB Browser installed, and leave other parameters to the default.
Table 5-19 Description of SNMP parameters

software agent supports.
The name must consist of numbers, letters, underlines and strikethroughs.
Trap Address| The target address of the Trap information sent by the software agent on the Device.
Trap Port| The target port of the Trap information sent by the software agent on the Device.
Keep Alive| After you select the checkbox, the Device can send data packet to ensure continuous network connection.
Read-only Username| Set the read-only username used to access the Device, and it is  public by default.   The name must consist of numbers, letters or underlines.
Read/Write Username| Set the read/write username used to access the Device, and it is  public by default.  The name must consist of numbers, letters or underlines.
Authentication Type| You can select MD5 or SHA. The default type is MD5.
Authentication Password| It cannot be less than 8 digits.
Encryption Type| It is CBC-DES by default.
Encryption Password| It cannot be less than 8 digits.

Step 3 Click Save.
Result
View device configuration through MIB Builder or MG-SOFT MIB Browser.

1. Run MIB Builder and MG-SOFT MIB Browser.
2. Compile the two MIB files with MIB Builder.
3. Load the generated modules with MG-SOFT MIB Browser.
4. Enter the IP address of the Device you need to manage in the MG-SOFT MIB Browser, and then select version to search.
5. Unfold all the tree lists displayed in the MG-SOFT MIB Browser, and then you can view the configuration information, video channel amount, audio channel amount, and software version.

Use PC with Windows OS and disable SNMP Trap service. The MG-SOFT MIB Browser will display prompt when an alarm is triggered.
5.2.9 Multicast
You can access the Device by network to see live view. If the access times exceed its upper limit, preview might fail. You can set multicast IP to access by multicast protocol to solve the problem. The Device supports two multicast protocols: RTP and TS. RTP is enabled by default when main stream and sub stream are used. TS is disabled by default.
5.2.9.1 RTP
Step 1 Select Setting > Network > Multicast > RTP.

Step 2 Enable main stream or sub stream.
Step 3 Enter multicast address and port number.
Step 4 Click Save.
5.2.9.2 TS
Step 1 Select Setting > Network > Multicast > TS.

Step 2 Enable main stream or sub stream.
Step 3 Enter multicast address and port number.
Step 4 Click Save.
5.2.10 Auto Register
After you enable this function, when the Device is connected to Internet, it will report the current location to the specified server which acts as the transit to make it easier for the client software to access the Device.
Step 1 Select Setting > Network > Auto Register.

Step 2 Select the Enable checkbox to enable Auto Register.
Step 3 Enter IP Address, Port and Sub-Device ID.
Table 5-20 Description of auto register parameter

Step 4 Click Save.
5.2.11 Wi-Fi
Devices with Wi-Fi function can access network through Wi-Fi.

• Wi-Fi and WPS are available on select models.
• All devices with WPS button support WPS function.
  5.2.11.1 Wi-Fi Settings
  The name, status and IP information of current hotspot are displayed in the Wi-Fi information bar.
  Click Refresh after reconnection to make sure that the operating status is displayed in real time.
  Connecting Wi-Fi hotspot takes some time depending on network signal strength.
  Step 1 Select the Enable checkbox.

Step 2 Click Search SSID, and Wi-Fi hotspots in the environment of current network camera are displayed.

It is recommended to set a secure encryption method for the Device to connect routers.
Step 5 Double-click one hotspot to display the Signal Quality and the Authentication Manner.

• If the password is required, enter the password. When entering the password, its index number shall be consistent with that on the router.
•  Click Connection if password is not required.

5.2.11.2 WPS Settings

PIN and SSID can be obtained from the router. Enter PIN and SSID, and then click Refresh to display operating status in real time.
5.2.11.3 AP Settings
You can use the Camera as wireless AP (Access Point), and other devices such as mobile phones can connect to the Camera by searching for the network name. You can then log in to the Camera through the browser on your device. At most 5 accounts can log in to the Camera at the same time. AP and Wi-Fi cannot be both enabled at the same time, and AP is disabled by default.
Procedure
Step 1 Select Setting > Network > WIFI > AP.
Step 2 Select Enable, and then set AP information.

Table 5-21 AP parameter description

devices connect to the Camera. It is 12345678 by default.
Parameter| Description
---|---
Host IP| Displays the IP address of AP.

Step 3 Click Save.
Result

1. Open your device such as mobile phone, search for the network name of the AP in the wireless signal list, and then connect to the network.
   After it is successfully connected, the IP address and MAC address of the device is displayed on the AP interface.

2. Open a browser on your device, enter the host IP on the AP interface or IP address on the TCP/IP interface, and then you can go to the login interface of the Camera.

3. Enter the username and password, and then log in to the Camera.
   Live view is available on select devices.

5.2.12 802.1x
802.1x is a port-based network access control protocol. It allows users to manually select authentication mode to control device access to LAN, and meet authentication, billing, safety and management requirements of the network.
Step 1 Select Setting > Network > 802.1x.

Step 2 Select the Enable checkbox to enable 802.1x.
Step 3 Select an authentication mode, and then enter username and password.
Table 5-22 Description of 802.1x setting parameter

from 0 to 63.

Command

| Data packet of device configuration and query. The value ranges from 0 to 63.
Open the WMM| Select the checkbox to enable wireless QoS.

Step 4 Click Save.
5.2.13 QoS
QoS (Quality of Service) is a network security mechanism, and is also a technology to solve network delay, congestion, and other problems.
For network business, QoS includes transmission bandwidth, time delay in transmission, and packet loss of data. In network, QoS can be improved by ensuring transmission bandwidth, and reducing time delay in transmission, packet loss rate, and delay jitter.
For DSCP (Differentiated Services Code Point), there are 64 priority degrees (0–63) of data packets. 0 represents the lowest priority, and 63 the highest priority. Based on the priority, the packets are classified into different groups. Each group occupies different bandwidth and has different discard percentage when there is congestion so as to improve service quality. Step 1 Select Setting > Network > QoS.

Step 2 Configure QoS setting parameters.
Table 5-23 Description of QoS setting parameter

from 0 to 63.
Command| Data packet of device configuration and query. The value ranges from 0 to 63.
Open the WMM| Select the checkbox to enable wireless QoS.

Step 3 Click Save.
5.2.14 4G/5G
After installing SIM card, you can connect the Device to 4G/5G network through dialing or mobile  setting.

• Dialing setting: Connect the Device to 4G/5G network in specified period.
• Mobile setting: Receive alarm linkage messages on your mobile phone. When receiving alarm messages, you can activate the Device to connect to 4G/5G network through SMS or phone calls.
• The function is available on devices with 4G/5G module. This section uses 4G as an example.
• Dual 4G is supported by select models, but only one 4G network adapter can be enabled simultaneously.

5.2.14.1 Dialing Setting
Log in to web page, select Setting > Network > 4G > Dialing Setting.

Some devices only support certain mobile carriers, and only the supported carriers are displayed in Network Support.
Step 1 Select the Enable checkbox.
Step 2 Enter APN, Authorize Mode, Dial-up Number, Username, and Password according to the  SIM card inserted.
These parameters might vary by countries. Contact local carrier or customer service for details.
Step 3 Set the period to use 4G.

• If the current time is in the period you set, 4G network connection will be enabled. The IP address of the SIM card will be displayed in IP Address. And you can access the device through 4G after finishing the rest steps.
• If the current time is not in the period you set, 4G network connection will not be enabled. Only the corresponding Wireless Signal is displayed on the page. And you cannot access the device through 4G.

Step 4 Set the interval to enable 4G through message or phone call if you want to use 4G outside the period set in Step3.
The value range is 0–7200 s and it is 30 s by default. If the interval is 30 s, after activating 4G, you can use it for 30 s. After 30 s, you need to activate 4G again. If you set the interval to 0 s, you can use 4G without disconnection and you do not need to activate it again. For the method to activate 4G through message or phone call, see “5.2.14.2 Mobile Setting”.
Step 5 Click Save.
5.2.14.2 Mobile Setting
Log in to web page, select Setting > Network > 4G > Mobile Settings.
You can add the phone number to receive alarms. You also can add phone number used to activate 4G through message or phone call if you want to use 4G outside the period set in Step3 of “5.2.14.1 Dialing Setting”.
Make sure that you add international calling codes before the phone number to avoid unnecessary charges caused by phone calls or messages to other countries or regions.

• Message Send: When alarms are triggered, the phone number added will receive message.

• Message Activation: You can enable 4G through message outside the period you set to use 4G.
  You need to send “ON” or “OFF” to phone number of the SIM card in the Device. “ON” indicates enabling, and “OFF” indicates disabling.

• Phone Activation: You can enable 4G through phone calls outside the period you set to use 4G. You need to call the phone number of the SIM card in the Device. If the call gets through, it means 4G has been enabled.

• Make sure that your SIM card supports making phone calls and sending messages, and it can be used normally.

• Make sure that you use activation function outside the time range you set; otherwise it does not work.

Step 1 Select the checkbox of the service you need to enable. You can select one or more services.
Step 2 Enter the phone number and click to add it.
Step 3 Click Save.
Step 4 Select the Message Link checkbox on the page of the event for which you want to receive message.
Take Face Detection for example. Click Setting > Event > Face Detection, and then select the Message Link checkbox.

Step 5 Click Save on the page of the corresponding event. You will receive message if the alarm is triggered.

Access Platform

5.2.15.1 P2P
P2P is a private network traversal technology which enables users to manage devices easily without requiring DDNS, port mapping or transit server. Scan the QR code with your smart phone, and then you can add and manage more devices on your mobile client.
Step 1 Select Setting > Network > Access Platform > P2P.

• P2P is enabled by default. You can manage the devices remotely.
• When P2P is enabled and the device is connected to network, the status is displayed as Online. We might collect the information including IP address, MAC address, device name, and serial number. The information collected is for remote access only. If you do not agree with this, you can clear the Enable checkbox.
  Step 2 Log in to mobile phone client, and then tap Device Management.
  Step 3 Tap Add + at the upper-right corner.
  Step 4 Scan the QR code on the P2P page.
  Step 5 Follow the onscreen instructions to finish settings.

ONVIF

The ONVIF authentication is On by default, which allows the network video products (including video recording device and other recording devices) from other manufacturers to connect to the service. Step 1 Select Setting > Network

Access Platform > ONVIF.

Step 2 Select On for Authentication.
Step 3 Click Save.
5.2.15.3 RTMP
You can connect the third party platforms (such as YouTube) to play live video through RTMP protocol.

• Only admin user can configure RTMP.
• RTMP only supports H.264, H.264B and H.264H video formats, and Advanced Audio Coding (AAC) audio format.
  Step 1 Select Setting > Network > Access Platform > RTMP.

Step 2 Select the Enable checkbox to enable RTMP.
When enabling RTMP, make sure that the address can be trusted.
Step 3 Set RTMP parameters.
Table 5-24 Description of RTMP parameter configuration

the stream is H.264, H.264B or H.264H, and the audio format is AAC.
Address Type| There are two options: Non-custom and Custom.

●      Non-custom : You need to fill in the IP address or domain name.

●      Custom : You need to fill in the address allocated by the server.

IP Address| If you have selected Non-custom , IP address and port need to be filled in.

●      IP Address: IPv4 or domain name is supported.

●      Port: It is recommended to use the default value.

Port
Custom Address| If you have selected Custom , the address allocated by the server needs to be filled in.

5.3 Bluetooth Settings
You can connect the Camera to Bluetooth devices such as Bluetooth headset for voice broadcast of alarms and voice intercom with the platform.
The function is available on select models.
Procedure
Step 1 Select Setting > Connection Settings > Bluetooth.
Step 2 Select Enable.
The searched Bluetooth devices are displayed in the Bluetooth List. Click Refresh at the lower-right corner of the list to search for Bluetooth devices again. Step 3 Double-click the name of Bluetooth device, and then set PIN on the Setup interface.
For the PIN of the Bluetooth device, see the corresponding user’s manual.
Step 4 Click Save.
The connected Bluetooth device is displayed in the list below.
Step 5 Select Setting > Camera > Audio > Audio, and then set audio input and audio output types to Bluetooth.

Related Operations

• Click Refresh at the lower-right corner of the list to get information of paired Bluetooth devices again.
• Click Pair Again to quickly connect to Bluetooth devices paired before.
• Click Delete to delete the Bluetooth device.
  5.4 PTZ Settings
  5.4.1 Protocol
  Network PTZ setting and analog PTZ setting are available on select models.
  5.4.1.1 Network PTZ Settings
  Step 1 Select Setting > PTZ > Protocol > Network PTZ.

Step 2 Select a protocol.
You can select DH-SD1, DH-SD3, PELCOD, or PELCOP. DH-SD1 is selected by default.
DH-SD1 protocol supports up to 80 presets, and DH-SD3 protocol supports up to 300 presets.
Step 3 Click Save.
5.4.1.2 Analog PTZ Settings
Step 1 Select Setting > PTZ > Protocol > Analog PTZ.

Step 2 Configure analog PTZ parameter.
Table 5-25 Description of analog PTZ parameter

Make sure that the address is the same as the device address; otherwise you cannot control the device.
Baud Rate| Select the baud rate of the Device.
Data Bit| It is 8 by default.
Stop Bit| It is 1 by default.
Parity| It is NONE by default.

5.4.2 Function
5.4.2.1 Preset
Select Setting > PTZ > Function > Preset. The Preset page is displayed.
If you click Remove All, all presets and special presets will be cleared.

5.4.2.1.1 Preset Settings
Preset means a certain position to which the Device rotates. Users can adjust the PTZ and camera to the location quickly through calling presets.
Step 1 On the lower left corner of the Preset interface, click the direction buttons, , , -and+ to adjust the PTZ direction, speed, zoom, and focus of the Device.
Step 2 Click + to add a preset.
The current position is set to a preset and is displayed in the list.

Step 3 Click to save the preset.
Step 4 Perform operations on presets.

• Double-click the preset title to edit the title displayed on the monitoring screen.
• Click to delete the preset.

5.4.2.1.2 Special Preset Settings
Special presets serve as the shortcut for some special functions switch or calling, and they no longer represent the location of the PTZ camera.
Step 1 Click+ to add a special preset. The added special preset will be displayed in the list.
The number of special presets starts from 51 by default, and 100 is the largest number.

Step 2 Click to save the added special preset.
Step 3 Perform operations on special presets.
If the PTZ is restored to default settings, all preset configurations will be cleared, but the called function will remain.
Related Operations

• Click to modify the special preset function.
• Click to delete the special preset.
• Click to quickly call the function configured for the special preset.

5.4.2.2 Tour
Tour means a series of movements that the Device makes along several presets.
5.4.2.2 Tour
Tour means a series of movements that the Device makes along several presets.

Step 2 Select the Tour Mode from Original Path and Shortest Path. Original Path is selected by default.

• Original Path: Tour in the order of adding presets.
• Shortest Path: Starting from the preset with largest horizontal zoom value and vertical zoom value, pass all presets in the tour to ensure the shortest path. The Device reaches the corresponding preset and ensure the minimum number of rotation.
  Step 3 Click Add at the bottom of the list on the upper right corner of the page to add a tour path.
  Step 4 Click Add at the bottom of the list on the lower right corner of the page to add several presets.

Step 5 Perform tour operations.

• Double-click tour name to edit the name of the corresponding tour.
• Double-click duration to set the time that the Device stays at the corresponding preset.
• Double-click speed to modify the tour speed. The default value is 7, and the value range is 1–10. The larger the value, the faster the speed.

Step 6 Click Start to start the tour.
The ongoing tour stops if any operation is made to the PTZ.
5.4.2.3 Scan
Scan means the Device moves horizontally at a certain speed between the defined left and right  limits.
Step 1 Select Setting > PTZ > Function > Scan.
Figure 5-71 Scan settings

Step 2 Select the Scan No..
Step 3 Drag the slider to adjust the scan speed.
Step 4 Click Setup to adjust the Device to an ideal position.
Step 5 Click Set Left Limit and Set Right Limit to set the left and right boundaries of the Device.
Step 6 Click Start, and then the Device starts scanning.
Step 7 Click Stop, and then the scanning stops.
5.4.2.4 Pattern
Pattern means a record of a series of operations that users make to the Device. The operations include horizontal and vertical movements, zoom and preset calling. Record and save the operations, and then you can call the pattern path directly.
Step 1 Select Setting > PTZ > Function > Pattern.

Step 2 Select the Pattern No..
Step 3 Click Setup and Start Rec, and then operate the PTZ.
Step 4 Click Stop Rec to stop recording.
Step 5 Click Start, and then the Device starts patterning.
Step 6 Click Stop, and then the patterning stops.
5.4.2.5 Pan
Pan refers to the continuous 360° rotation of the Device at a certain speed.
Step 1 Select Setting > PTZ > Function > Pan.

Step 2 Drag the slider to set the Pan Speed.
Step 3 Click Start, and the Device starts to rotate horizontally at this speed.
5.4.2.6 PTZ Speed
You can adjust the manual control speed of the PTZ by setting PTZ speed. This speed does not apply
to tour, pattern, or auto tracking.
Step 1 Select Setting > PTZ > Function > PTZ Speed.

5.4.2.7 Idle Motion
Idle motion refers to a set motion when the Device does not receive any valid command within a  ertain period.
Set Preset, Tour, Scan or Pattern in advance.
Step 1 Select Setting > PTZ > Function > Idle Motion.

Step 2 Select the Enable checkbox to enable the idle motion.
Step 3 Select idle motion from Preset, Tour, Scan and Pattern.
Step 4 Select the action number of the selected motion.
Step 5 Set Idle Time for the selected motion.
Step 6 Click Save.
5.4.2.8 PowerUp
PowerUp means the automatic operation of the Device after it is powered on.
Set Preset, Tour, Scan or Pattern in advance.
Step 1 Select Setting > PTZ > Function > PowerUp.

Step 2 Select the Enable checkbox to enable power up motion.
Step 3 Select power up motion from Preset, Tour, Scan, Pattern or Auto.
Select Auto and the last motion before you shut down the Device last time will be performed.
Step 4 Select the action number of the selected motion.
Step 5 Click Save.
5.4.2.9 PTZ Limit
After you set the PTZ limit, the Device can only move in the defined area.
Step 1 Select Setting > PTZ > Function > PTZ Limit.

Step 2 Adjust the PTZ direction, and then click Setting to set the Up Line.
Step 3 Adjust the PTZ direction, and then click Setting to set the Down Line.
Step 4 Click Live to preview the already-set up line and down line.
Step 5 Select the Enable checkbox to enable the PTZ limit function.
5.4.2.10 Time Task
After you set time task, the Device performs the selected motions during the defined period.
Set Preset, Tour, Scan or Pattern in advance.
Step 1 Select Setting > PTZ > Function > Time Task.

Step 2 Select the Enable checkbox to enable time task function.
Step 3 Set the time task number.
Click Clear All to delete all set time tasks.
Step 4 Select Time Task action such as Preset, Tour, Scan or Pattern.
Step 5 Select the action number of the selected motion.
Step 6 Set the time for AutoHome.
AutoHome refers to the time needed to automatically recover the time task in case of manually calling the PTZ to stop the time task.
Step 7 Click Period setting to set the period to perform time tasks.
Step 8 Select the task number to copy settings to the selected task, and then click Copy.
Step 9 Click Save.
5.4.2.11 PTZ Restart
Step 1 Select Setting > PTZ > Function > PTZ Restart.

Step 2 Click PTZ Restart.
The PTZ is restarted.
5.4.2.12 Default
With the function, you can restore the PTZ to factory defaults.
This function will restore the Device to defaults. Think twice before performing the operation.
Step 1 Select Setting > PTZ > Function > Default.

Step 2 Click Default.
The PTZ will be restored to factory defaults.
5.5 Event Management
5.5.1 Video Detection
Video detection includes three event types: Motion Detection, Video Tamper and Scene Changing.
5.5.1.1 Motion Detection
When the moving object appears and moves fast enough to reach the preset sensitivity value, alarms will be triggered.
Step 1 Select Setting > Event > Video Detection > Motion Detection.

Step 2 Select the Enable checkbox, and then configure motion detection parameters.
● Set arming and disarming period.

1. Click Setting, and then set the arming period on the page.

2. Set the alarm period to enable alarm events in the period you set. ◇
   There are 6 time periods for each day. Select the check box for the time period to enable it.
   ◇ Select the day of week (Sunday is selected by default; If All is selected, the setting is applied to the whole week. You can also select the check box next to the day to set it separately).

3. After completing the settings, click Save.
   You will return to the Motion Detection page.
   ● Set the area.
   Click Setting, and the Area page is displayed. Refer to Table 5-26 and Table 5-27 for parameters description. Each color represents a certain region, and you can set different motion detection regions for each area. The detection region can be irregular and discontinuous.

Table 5-26 Description of area setting parameter

Name

| The default names are Region1, Region2, Region3 and Region4, and the names can be customized.

Sensitivity

| Sensitivity to brightness change. The higher the sensitivity is, the easier the motion detection event will occur.

You can set different sensitivities for each region, with values ranging from 0 to 100, and 30 to 70 is recommended.

Threshold

| Detect the relation between the object and the region. The smaller the threshold is, the easier the motion detection will occur.

Set different thresholds for each region, with values ranging from 0 to 100, and 1 to 10 is recommended.

Waveform graph

| The red line indicates that motion detection is triggered, and the green line indicates that it is not triggered.
Remove All| Remove all detection regions.
Delete| Delete the detection region of the selected color block.

● Other parameters
Table 5-27 Description of video detection parameter

defined period. The value range is 0–100 s.
Enable Manual Control Trigger| After you enable the function, the motion detection events that occur when you control the PTZ manually will be excluded. In this way, you can reduce the false alarm rate of such events.
Parameter| Description
---|---

Record

| After you enable the function, when an alarm is triggered, the system will start recording automatically. Before using the function, you need to set the recording period of the alarm in Storage > Schedule , and select Auto for Record Mode on the Record Control page.

Record Delay

| When the alarm is over, the alarm recording will continue for an extended period of time. The time unit is second, and the value range is 10–300.

Relay-out

| Select the checkbox, and you can enable the alarm linkage output port, and link corresponding relay-out devices after an alarm is triggered.

Alarm Delay

| When the alarm is over, the alarm will continue for an extended period of time. The time unit is second, and the value range is 10–300.

Send Email

| After you select the checkbox, when an alarm is triggered, the system sends email to the specified email address. You can configure the email address in “5.2.5 SMTP (Email).”

PTZ

| Select PTZ , and then configure the linkage action. When an alarm is triggered, the system links PTZ to rotate to the preset. The Activation options include None , Preset , Tour and Pattern.

Snapshot

| Select the Snapshot check box, and then the system takes snapshot automatically when an alarm is triggered. You need to set the alarm snapshot period as described in “5.5.1.2 Snapshot.”

Step 3 Click Save.
5.5.1.2 Video Tamper
Alarms will be triggered if there is video tampering.
Step 1 Select Setting > Event > Video Detection > Video Tamper.

Step 2 Select the Enable checkbox, and then configure video tamper parameters.
For parameters configuration, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.1.3 Scene Changing
Alarms will be triggered if there is scene changing.
Step 1 Select Setting > Event > Video Detection > Scene Changing.

Step 2 Select the Enable checkbox, and then configure scene changing parameters.
For parameters configuration, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.2 Smart Motion Detection
After you set smart motion detection, when the human, non-motor vehicles and motor vehicles appear and move fast enough to reach the preset sensitivity value, the alarm linkage actions will be performed. The function can help you to avoid the alarms triggered by natural environment change.

• The function depends on the result of motion detection, and all other parameters (except sensitivity) of motion detection function are used, including arming period, area settings, and linkage configurations. If no motion detection is triggered, smart motion detection will not be triggered.
• If motion detection is not enabled, when smart motion detection is enabled, motion detection will also be enabled. If both functions are enabled, when motion detection is disabled, smart motion detection will also be disabled.
• When smart motion detection is triggered and recording is linked, back-end devices can filter recording with human or vehicles through smart search function. For details, see the corresponding user’s manual.

Prerequisites

• Select Setting > Event > Video Detection > Motion Detection, and then enable the motion detection function.
• Set the arming period and detection area. The sensitivity of each region is larger than 0, and the threshold is not equal to 100.

Procedure

1. Select Setting > Event > Smart Motion Detection.

2. Select the Enable checkbox to enable Smart Motion Detection.

3. Select the effective object and sensitivity.
   ● Effective object: Select Human or Motor Vehicle. When Human is selected, both people and non-motor vehicles will be detected.
   ● Sensitivity: Select High, Medium, or Low. The higher the sensitivity, the easier the alarm is triggered.

4. Click Save.

5.5.3 Audio Detection
Step 1 Select Setting > Event > Audio Detection > Audio Detection.

Step 2 Configure audio detection parameter.
Table 5-28 Description of audio detection parameter

when there is abnormal audio input.
Intensity Change| Select Intensity Change , and then an alarm is triggered when the change in sound intensity exceeds the defined threshold.

Sensitivity

| The value ranges from 1 to 100. The smaller this value is, the larger the input sound volume changes are needed for it to be judged as an audio anomaly. You need to adjust it according to the actual condition.
Threshold| The value ranges from 1 to 100. Configure the ambient sound intensity you need to filter. The louder the ambient noise is, the larger this value shall be. You need to adjust it according to the actual condition.

For other parameters, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.4 Smart Plan
Smart plans include IVS, face recognition, heat map, people counting, video metadata, construction monitoring and so on. Only after smart plans have been enabled, can the corresponding smart function come into effect.
Before configuring the smart plan, you need to set presets in advance. For setting methods, see “5.4.2.1 Preset”.
Step 1 Select Setting > Event > Smart Plan. 

Step 2 (Optional) Click to enable Auto Tracking.
When enabling auto tracking, you do not need to configure smart plans, and the Device performs auto tracking based on internal mechanism. If auto tracking and alarm track of the smart plan (such as IVS) are both enabled, the Device perform tracking in the order of triggering time.
It is recommended to disable auto tracking when alarm track is enabled to avoid disordered tracking. Step 3 Click to select the presets to be configured.
Step 4 Select smart plans.
The selected function will be highlighted. Click it again to cancel the selection.

Step 5 Click Save.
5.5.5 IVS
Basic Requirements for the Scene

• The target size shall not exceed 10% of the image.

• The pixel of the target shall be no less than 10×10; the pixel of abandoned object shall be no less than 15×15 (CIF image); the width and height of the target shall be no more than 1/3 of the image.
  It is recommended that the height of the target is 10% of the image.

• The brightness difference between the target and the background is no less than 10 gray values.

• The target shall be present in the image for no less than 2 consecutive seconds, and the moving distance shall be larger than its width and no less than 15 pixels (CIF image).

• Try to reduce the complexity of monitoring scenes. It is not recommended to enable IVS in scenes with dense targets and frequent light changes.

• Try to avoid the following scenes: scenes with reflective surfaces such as glass, bright ground or water; scenes that disturbed by tree branches, shadows or winged insects; scenes that against light or under direct light exposure.
  Before using the function, you need to set presets in advance. For setting methods, see “5.3.2.1 Preset.”

Rule Config

1. Select Setting > Event > IVS > Rule Config.

2. Select the presets to be configured with smart rules.

3. Click+ to add smart rules.
   Double-click rule type to modify the type of rules.

4. Click Save.

5.5.5.1 Tripwire
Alarms are triggered when the target crosses the warning line in the defined direction. It requires certain stay time and moving space for the target to be confirmed, so you need to leave some space at both sides of the warning line during configuration and do not draw it near obstacles. Applicable scenes: Scenes with sparse targets and no occlusion between targets, such as perimeter protection of unattended areas.
Procedure
Step 1 Select Tripwire from the Rule Type list.

Step 2 Click Draw Rule, and you can draw rules on the monitoring screen.
Click Clear to the right of Draw Rule to clear all drawn rules.
Table 5-29 Description of rule drawing parameter

the maximum or minimum size.

●      Max Size: Set the maximum size of targets to be filtered. When the target is larger than this size, the system will ignore it. The unit is pixel.

●      Min Size: Set the minimum size of targets to be filtered. When the target is smaller than this size, the system will ignore it. The unit is pixel.

Min Size

Pixel Counter

| Help to accurately draw the target area.

Enter the length and width of the target area in Pixel Counter , and click Draw Target to generate the target area in the monitoring screen. The unit is pixel.

Lock/Unlock

| Enter the rule configuration page, and the locking function will be automatically enabled, and the locking time is 180 s. During this period, the device cannot track the target. Click Unlock to release the control.

The locking function only takes effect in the rule configuration page. After switching to the Live page, the Device can track the target normally.

Step 3 Configure tripwire parameter.
Table 5-30 Description of tripwire parameter

Period

| Set the alarming period to enable alarm events in the defined period.

1.     Click Setting , and then the Period interface is displayed.

2.     Enter the time value or press and hold the left mouse button, and drag directly on the setting interface. There are six periods for each day. Select the checkbox next to the period for it to take effect.

3.     Select the day of week ( Sunday is selected by default; If All is selected, the setting is applied to the whole week. You can also select the checkbox next to the day to set it separately).

4.     After completing the setting, click Save to go back to the rule

configuration interface.

Direction| Configure the tripwire direction. You can select A- >B, B- >A or A <->B.

Alarm Track

| Select the checkbox, and there will be alarm tracking when a smart rule is triggered.
Track Time| Set the alarm tracking time.

Record

| Select the checkbox, and when an alarm is triggered, the system will start recording automatically. Before using the function, you need to set the recording period of the alarm in Storage > Schedule , and select Auto for Record Mode on the Record Control interface.

Record Delay

| When the alarm is over, the recording will continue for an extended period of time. The value range is 10–300 s.

Relay-out

| Select the checkbox, and you can enable the alarm linkage output port, and link corresponding relay-out devices when an alarm is triggered.

Alarm Delay

| When the alarm is over, the alarm will continue for an extended period of time. The value range is 10–300 s.

Send Email

| Select the Send Email checkbox, and when an alarm is triggered, the system sends an email to the specified mailbox. You can configure the mailbox in Setting > Network > SMTP (Email).

Snapshot

| Select the checkbox, and the system will automatically take snapshots in case of alarms. You need to set snapshot period in Storage > Schedule.

Step 4 Click Save.
5.5.5.2 Intrusion
Intrusion includes crossing areas and in-area functions.

• Crossing area means an alarm will be triggered when a target enters or leaves the area.
• In-area function means an alarm will be triggered when a specified number of targets appear in a set alarming area at a given time. In-area function only counts the number of targets in the detection area, regardless of whether they are the same targets.
• For the reporting time interval of the in-area functions, the system will trigger the first alarm and then detect whether the same event occurs in the interval period. If no same event occurs in this period, the alarm counter will be cleared.
  Similar to the warning line, to detect an entry/exit event, a certain movement space should be reserved at the periphery of the area line.
  Applicable scenes: Scenes with sparse targets and no occlusion between targets, such as perimeter protection of unattended areas.
  Step 1 Select Intrusion from the Rule Type list.

Step 2 Click Draw Rule, and you can draw rules on the monitoring screen.
For parameter description, see Table 5-29.
Click Clear to the right of Draw Rule to clear all drawn rules.
Step 3 Configure intrusion parameter.
Table 5-31 Description of intrusion parameter

Cross.
Direction| Select the crossing direction from Enters , Exits , and Enter & Exit.

For other parameters, see “5.5.5.1 Tripwire”.
Step 4 Click Save.
5.5.5.3 Abandoned Object
An alarm will be triggered when the selected target in the monitoring scene stays in the screen for more than the defined time.
Pedestrians or vehicles that stay for too long would be regarded as abandoned objects. To filter out such alarms, you can use Target filter. In addition, the duration can be properly extended to avoid false alarm due to a short stay of people.
Applicable scenes: Scenes with sparse targets, no obvious and frequent light changes. For scenes with intensive targets or too many obstacles, missed alarms would increase; for scenes in which too many people stay, false alarms would increase. Select detection areas with simple texture, because this function is not applicable to scenes with complex texture.
Step 1 Select Abandoned Object from the Rule Type list.

Step 2 Click Draw Rule, and you can draw rules on the monitoring screen.
For parameter description, see Table 5-29.
Click Clear to the right of Draw Rule, and you can clear all drawn rules.
Step 3 Configure abandoned object parameter.
Table 5-32 Description of abandoned object parameter

Duration

| For abandoned object, the duration is the shortest time to trigger an alarm after an object is abandoned.

alarm after an object is abandoned.
For other parameters, see “5.5.5.1 Tripwire”.
Step 4 Click Save.
5.5.5.4 Missing Object
An alarm will be triggered when the selected target in the scene is taken away for the time longer than the set duration.
The system analyzes static areas from the foreground, and determines whether it is missing object or abandoned object from the similarity of its foreground and background. When the time exceeds the set period, an alarm is triggered.
Applicable scenes: Scenes with sparse targets, no obvious and frequent light changes. For scenes with intensive targets or too many obstacles, the missed alarm would increase; for scenes in which too many people stay, the false alarm would increase. Keep the detection area texture as possible simple as possible, because this function is not applicable to scenes with complex texture. Step 1 Select Missing Object from the Rule Type list.

Step 2 Click Draw Rule, and you can draw rules on the monitoring screen.
For parameter description, see Table 5-29.
Click Clear to the right of Draw Rule to clear all drawn rules.
Step 3 Configure missing object parameter.
Table 5-33 Description of missing object parameter

alarm being triggered.

For other parameters, see “5.5.5.1 Tripwire”.
Step 4 Click Save.
5.5.6 Construction Monitoring
The Device can be used for construction monitoring which include helmet detection, workwear detection, lone working detection and absence detection.
Prerequisites
Select Setting > Event > Smart Plan to enable Construction Monitoring.
Procedure
Step 1 Select Setting > Event > Construction Monitoring.
Step 2 Select Global or a preset from the Preset list.

• If global plan is selected, detection area and rule are set by default, and the detection area cannot be changed.
• If a preset is selected, you need to set detection area and rule manually. The following section uses selecting Preset 1 as an example.

Step 3 Click + at the upper-right corner of the Area Config section.
Double click the rule name to modify it. Step 4 Click to draw rule box on the video image, and then right-click to complete drawing.

• After drawing is complete, drag the corners of the drawn area to adjust the detection area.
• If you select preset plan, 8 detection areas can be drawn at most.
  Step 5 Select the checkbox before the event type to enable the corresponding detection rule.
  Table 5-34 Rule description

Helmet Detection

| When the Device detects person not wearing helmet or not wearing helmet in the specified color, alarm linkage actions will be performed.

Workwear Detection

| When the Device detects person not wearing workwear in accordance with the rule, alarm linkage actions will be performed. The rule for workwear is long- sleeved tops and trousers in the same color. If short-sleeved shirts, shorts or different colors are detected, it means the rule is not followed.
Lone Working Detection| When the Device detects a single person working in the detection area, alarm linkage actions will be performed.
Absence Detection| When the Device detects nobody working in the detection area, alarm linkage actions will be performed.

Step 6 Click next to the detection rule, configure parameters on the Advanced Parameter interface, and then click Save.

Allowed Color

| When configuring helmet detection, you can set allowed colors. When the helmet detected is not in the selected colors, alarms will be triggered.

Duration

| When events not following the rule are detected and the duration exceeds the defined value, alarms will be triggered. For example, when the duration of helmet detection is 5 seconds, if the Device detects a person not wearing helmet or the helmet color is not allowed for more than 5 seconds, an alarm will be triggered.
Parameter| Description
---|---

Repeat Alarm Time

| After an alarm is triggered, when the event lasts for the time reaching repeated alarm time, an alarm will be triggered again.

Record

| After you enable the function, when an alarm is triggered, the system will start recording automatically. Before using the function, you need to set the recording period of the alarm in Storage > Schedule , and select Auto for Record Mode on the Record Control interface.

Record Delay

| When an alarm is over, the alarm recording will continue for an extended period of time.

Relay-out

| Select the checkbox, and you can enable the alarm linkage output port, and link corresponding relay-out devices after an alarm is triggered.

Alarm Delay

| When an alarm is over, the alarm will continue for an extended period of time.

Send Email

| After you select the checkbox, when an alarm is triggered, the system sends email to the specified email address. You can configure the email address in “5.2.8 SNMP”.

Audio Linkage

| Select the checkbox to play alarm audio when alarms are triggered. You can set the play count and select the audio file. For how to set the audio file, see “5.1.3.2 Configuring Alarm Audio”.
Message Link| Select the checkbox to receive message when alarms are triggered.

Snapshot

| Select the checkbox, and the system will automatically take snapshots in case of alarms. You need to set snapshot period in Storage > Schedule.

Period

| Set the alarm period to enable alarm events in the defined period.

1.     Click Setup , and the Period interface is displayed.

2.     Enter the time value or press and hold the left mouse button, and drag directly on the setting interface. There are six periods for each day. Select the checkbox next to the period for it to take effect.

3.     Select the day of week ( Sunday is selected by default; If All is selected, the setting is applied to the whole week. You can also select the checkbox next to the day to set it separately).

4.     After completing the setting, click Save to go back to the rule

configuration interface.

Step 7 Click Save on the Construction Monitoring interface.
If you want to see the alarm information on the Alarm tab, you need to subscribe the corresponding alarm type. For details, see “6 Alarm”.
Result
Click the AI Live tab to view construction monitoring results. For details, see “3.2 AI Live Settings”.
5.5.7 Face Recognition
The function can detect faces and compare them with those in the configured face database.

•  Select Setting > Event > Smart Plan to enable face recognition.
• This function is available on select models.
  5.5.7.1 Face Detection
  When human face is detected in the monitoring screen, an alarm is triggered and the linked action is performed.
  Step 1 Select Setting > Event > Face Recognition > Face Detection.

Step 2 Select Enable to enable the face detection function.
Step 3 Configure face detection parameters.
Table 5-36 Description of face detection parameter

Period

| Alarm event will be triggered only within the defined period. For details, see “5.5.1.1 Motion Detection”.

Face Enhancement

| Select Face Enhancement to preferably guarantee clear faces with low stream.

Record

| Select Record , and the system records video when alarms are triggered.

To enable video recording, you need to make sure that:

●      The motion detection recording is enabled. For details, see “5.6.1.1 Record”.

●      The auto recording is enabled. For details, see “5.6.4 Record Control”.

Record Delay

| The video recording will not stop until the record delay time you set has passed.
Parameter| Description
---|---

Send Email

| Select Send Email , and when alarms are triggered, the system sends email to the specified mailbox. For the email settings, see “5.2.5 SMTP (Email)”.

Snapshot

| Select Snapshot , and the system takes snapshot when alarms are triggered.

●      Enable the motion detection snapshot first. For details, see “5.6.1.1 Record”.

●      For searching and setting snapshot storage path, see “5.1.2.5 Path”.

Snap Face Image| Set the snapshot scope, including Face and One-inch photo.

Attribute

| Select the Attribute checkbox, click , and then you can set the human attributes during face detection.

Step 4 Click Save.
5.5.7.2 Face Database Config
After you successfully configure the face database, the detected faces can be compared with the information in the face database. Configuring a face database includes creating a face database, adding face images, and face modeling.
5.5.7.2.1 Adding Face Database
Create a face database, and then register face images to add face images to the newly created face database.
Step 1 Select Setting > Event > Face Recognition > Face Database Config.

Step 3 Set face database name.
Step 4 Click OK to complete the addition.

Step 5 Configure face database configuration parameters.
Table 5-37 Description of face database config parameter

Similarity Threshold

| The comparison is successful only when the similarity between the detected face and the face feature in face database reaches the set similarity threshold. After this, the comparison result is displayed on the Live page.

More Info

| Click More Info to manage face database. You can set search conditions, register people, and modify people information.

Arm/Disarm

| Alarm event will be triggered only within the defined time period. For details, see “5.5.1.1 Motion Detection”.
Delete| Delete the selected face database.

5.5.7.2.2 Adding Face Images
You can add face images to the created face database. Manual addition and batch import are supported.
Manual Addition
Add a single face image. Use this method when registering a small number of face images.
Step 1 Select Setting > Event > Face Recognition > Face Database Config.
Step 2 Click More Info for the face database to be configured.

Set filtering conditions, and then click Search. The search result is displayed.
Step 3 Click Registration.

Step 4 Click Upload Picture, and then import the face pictures to be uploaded.
You can manually select a face area. After uploading the picture, select a face area and click OK. If there are multiple faces in an image, select the target face and click OK to save the face image.

Step 5 Fill in face image information.
Step 6 Click Add to task list.
Step 7 Click .

Batch Registration
You can import multiple face images in batches. Use this method when registering a large number of face images.
Before importing images in batches, name the face images in the format of “Name#SGender#BDate of Birth#NRegion#TCredentials Type#MID No. jpg” (for example, “John#S1#B1990-0101#NCN#T1#M330501199001016222”).
Name is required and the rest are optional.
Table 5-38 Naming rules for batch import

2017-11-23.
Region| Enter the region name.
Credentials Type| Enter a number. 1: ID card; 2: passport.
ID No.| Enter ID No.

Step 1 Select Setting > Event > Face Recognition > Face Database Config.
The Face Database Config interface is displayed.
Step 2 Click More Info for the face database to be configured.
The Face Database interface is displayed.
Step 3 Click Batch Registration.

Step 6 After the registration is completed, click Next to view the registration result.
5.5.7.2.3 Managing Face Images
You can add face images to face database; manage and maintain face images to ensure correct information.
Modifying Face Information
On the Face Database Config page, move the mouse pointer to the face image or person information line, and then click or . After modifying the face image information, click Add to task list.

Deleting Face Images
Enter face database, and then delete the created face image.

• Single deletion: Move the mouse pointer to the face image or people information line, and then click or to delete the face image.
• Batch deletion: Move the mouse pointer to the face image or people information line, and then click at the upper right corner of the face images, or click on person information line. After selecting multiple items, click Add to the delete list, click , and then click OK to delete the selected face images.
• Delete all: When viewing face images in a list, click on people information line (or select All when viewing face images in images), click Add to the delete list, click , and then click OK to delete all face images.

5.5.7.2.4 Face Modeling
You can extract and import the relevant information of face images into the database through face modeling, and create a face feature mode for smart detection such as face comparison.

• The more face images you choose, the longer the modeling time is.
• During the modeling process, some smart detection functions (such as face comparison) are temporarily unavailable and can be resumed after the modeling is complete.
  Step 1 Select Setting > Event > Face Recognition > Face Database Config.
  Step 2 Click More Info for the face database to be configured.

Step 3 Select the face images for modeling  Click to view the face image in a list. Click to view the face image as a thumbnail.

• Modeling All Click Modeling All, and all face images in the face database will be modeled.
• Selective Modeling
  If there are many face images in the face database, set filtering conditions and then click Search to select face images for modeling.

5.5.7.3 Alarm Linkage
Set the alarm linkage mode for face comparison.
Step 1 Select Setting > Event > Face Recognition > Alarm.

Table 5-39 Description of alarm linkage parameter

Relay-out

| Select the Relay-out checkbox, and when an alarm is triggered, the system interacts with the linked alarm devices.

Alarm Delay

| The alarm will continue for an extended period of time. The value range is 1–300 s.

5.5.8 People Counting
You can use this function to count the number of people in the area and generate reports.

• Before using this function, you need to enable People Counting in Smart Plan.
• The people counting data will be overwritten if the disk is full. Back up the data in time as needed.
• This function is available on select models.

5.5.8.1 People Counting Settings
With the function, the system can count the number of people appearing in the monitoring screen within a certain period.
Step 1 Select Setting > Event > People Counting > People Counting.

Step 2 Select the presets to be configured.
Step 3 Click Draw Rule, and you can draw rules on the monitoring screen. For parameter description, see Table 5-29.
Click Clear to the right of Draw Rule, and you can clear all drawn rules.
Step 4 Configure people counting parameter.
Table 5-40 Description of people counting parameter

OSD

| Display the number of people displayed in the area in real time. Click

Clear , and the current number will be zero.

Enter No.

| Set the Enter No. , and when the number of people entering reaches the set value, an alarm will be triggered.

Leave No.

| Set the Leave No. , and when the number of people leaving reaches the set value, an alarm will be triggered.

Stranded No.

| Set the Stranded No. , and when the number of people staying reaches the set value, an alarm will be triggered.

For other parameters, see “5.5.5.1 Tripwire”.
Step 5 Click Save.
5.5.8.2 Report
You can view the statistics results of people in the scene during the selected period.
Step 1 Select Setting > Event > People Counting > Report.
Figure 5-117 People counting report

Step 2 Select a preset.
Step 3 Select the Rule, Statistics Type, and Time Range.
Step 4 Select the start time and end time for searching reports.
Step 5 Select Flow Direction and Chart Type.
Step 6 Click Search to generate reports, and then click Export to export the report to local storage.
5.5.9 Heat Map

• Before enabling Heat Map, you need to set presets in PTZ section, and select the function in the Smart Plan.
• The data will be overwritten if the disk is full. Back up the data in time.
• This function is available on select models.

5.5.9.1 Heat Map Settings
The function can be used to detect the activity level of moving objects in the scene during a certain period.
Step 1 Select Setting > Event > Heat Map > Heat Map.

Step 2 Select the presets to be configured.
Step 3 Select the Enable checkbox to enable heat map function.
Step 4 Click Setting to set the arming period. For details, see “5.5.1.1 Motion Detection”.
Step 5 Click Save.
5.5.9.2 Report
You can view the heat map report for the scene in the selected period.
Step 1 Select Setting > Event > Heat Map > Report.
Step 2 Set the start time and end time to search for the heat map report.
Step 3 Select a preset.
Step 4 Click Search, and the search results will be displayed on the page.

5.5.10 Video Metadata
With the function, the system can count the number of motor vehicles, non- motor vehicles and people in the monitoring screen, identify the features of the vehicles and people in the scene, and take snapshots.

• Before using video metadata, you need to enable the function in the Smart Plan.
• This function is available on select models.

5.5.10.1 Scene Setting
Set the parameters of snapshot, analysis and alarm in the scene.
Step 1 Select Setting > Event > Video Metadata.

Step 2 Click the Preset list to select the preset to configure video metadata.
Step 3 Click + to add a rule type.
Step 4 Modify the parameters.
● Double-click the name to modify the rule name.
● Select the rule type from People, Non-motor Vehicle and Motor Vehicle.
● Click the corresponding to delete detection items.
Step 5 Configure scene setting parameters.
Table 5-41 Description of scene setting parameter

After selection, traffic flow statistics will be displayed on the screen.

Non-motor Vehicle Flow Statistics
Traffic Flow Statistics

OSD

| Select the checkbox to enable the OSD overlay. The statistics will be displayed on the Live page in the form of OSD information.

Clear

| Click it to clear the statistics of motor vehicles, non- motor vehicles and people.

For other parameters, see “5.5.5.1 Tripwire”.
Step 6 Click Save.
5.5.10.2 Picture Overlay
Set the overlay information on the snapshot.
Step 1 Select Setting > Event > Video Metadata > Overlay.
Step 2 Select Picture Overlay Type from People, Non-motor Vehicle and Motor Vehicle.

Step 3 Select overlay information.
If you select Location, you need to manually enter the location of the Device.
Step 4 Click Save.
5.5.10.3 Report
You can view the number of vehicles, non-vehicles and people in the scene during the selected period.
Step 1 Select Setting > Event > Video Metadata > Report.
Step 2 Select the Report Type.
Step 3 Select the start time and end time for searching reports.
Step 4 Select Traffic Flow Statistics Type.
Step 5 Click Search to generate reports.

5.5.11 Alarm
Step 1 Select Setting > Event > Alarm.

Step 2 Configure alarm setting parameters.
Table 5-42 Description of alarm setting parameter

Sensor Type

| There are two types: NO (normally open) and NC (normally closed). Switch from NO to NC , and alarm event will be enabled. Switch from NC to NO , and alarm event will be disabled.

For other parameters, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.12 Abnormality
Abnormality includes 7 alarm events: No SD Card, Capacity Warning, SD Card Error, Disconnection, IP Conflict, Illegal Access, and Security Exception.
5.5.12.1 SD Card
In case of an SD card exception, an alarm will be triggered.
Step 1 Select Setting > Event > Abnormality > SD Card.

Table 5-43 Description of SD card exception parameter

the SD card is less than the defined percentage, an alarm is triggered.

For other parameters, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.12.2 Network Exception
In case of a network exception, an alarm will be triggered.
Step 1 Select Setting > Event > Abnormality > Network.

Table 5-44 Description of network exception parameter

For other parameters, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.12.3 Illegal Access
Illegal access alarm is triggered when the login password has been wrongly entered for more than the times you set.
Step 1 Select Setting > Event > Abnormality > Illegal Access.

Step 2 Configure illegal access parameters.
Table 5-45 Description of illegal access parameter

illegal access will be triggered, and the account will be locked.

For other parameters, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.12.4 Security Exception
When an event affecting the Device safety occurs, an alarm for safety exception will be triggered.
Step 1 Select Setting > Event > Abnormality > Security Exception.  Step 2 Configure security exception parameter.
For details, see “5.5.1.1 Motion Detection”.
Step 3 Click Save.
5.5.12.5 Battery Exception
When overtemperature of the battery is detected, alarm linkage actions are performed.
Step 1 Select Setting > Event > Abnormality > Battery Exception.  Step 2 Select the Enable checkbox to enable battery exception detection.
Step 3 Set alarm linkage actions.
Step 4 Click Save.

Storage

5.6.1 Schedule
Before setting the schedule, make sure that the Record Mode is Auto in Record Control.
If the Record Mode is Off, the Device will not record or take snapshots according to the schedule.
5.6.1.1 Record
Step 1 Select Setting > Storage > Schedule > Record.

Step 2 Select the day for recording from Monday to Sunday, and then click Setting on the right.

• Set the recording period. You can set up to six periods for one day.
• You can select 3 types of recording: General, Motion and Alarm.

To set the time period, you can also press and hold the left mouse button and drag directly on the Record page.

Step 3 Click Save to return to the Record page.
At this time, the colored chart visually displays the defined period.

| ● : Represents general recording.
---|---
● : Represents motion detection recording.
● : Represents alarm recording.

Step 4 On the Record page, click Save, and the Save Succeeded! prompt will be displayed, which means the recording schedule has been set.
5.6.1.2 Snapshot
Step 1 Select Setting > Storage > Schedule > Snapshot.
Step 2 Set snapshot schedule.
For details, refer to Step2 and Step3 in “5.6.1.1 Record”.
Step 3 Click Save, and the Save Succeeded! prompt will be displayed, which means the snapshot schedule has been set.
5.6.1.3 Holiday Schedule
You can set specific dates as holidays.
Step 1 Select Setting > Storage > Schedule > Holiday Schedule.

Step 2 Select a date.
The selected date will be a holiday and displayed in yellow.
Step 3 Select Record or Snapshot, and then click Save.
The Save Succeeded! prompt will be displayed.
Step 4 On the Record or Snapshot page, click Setting to the right of Holiday.
The setting method is the same as that of Monday to Sunday.
Step 5 Set the period of one day for the Holiday, and the recording or snapshot will be taken according to the holiday time period.
5.6.2 Snapshot by Location
The system can take snapshots when the Device rotates to certain presets.
You need to set presets in advance.
Step 1 Select Setting > Storage > Snapshot by Location.

Step 2 Select presets.

• Enable snapshot by location.
  ◇ Click to enable the function for the corresponding preset.
  ◇ Click , and then select All Enabled to enable the function for all presets.

• Disable snapshot by location.
  ◇ Click to disable the function for the corresponding preset.
  ◇ Click , and then select All Disabled to disable the function for all presets. Step 3 Click Save.

Destination

5.6.3.1 Path
Configure the storage path of recordings and snapshots of the Device, and select local SD card, FTP and NAS for storage. Store recordings and snapshots according to the event type, respectively corresponding to General, Motion and Alarm in the schedule, and then select the corresponding type of recordings or snapshots for storage.
Step 1 Select Setting > Storage > Destination > Path.

Step 2 Select the corresponding event type and storage method.
Table 5-46 Description of path parameter

Step 3 Click Save.
5.6.3.2 FTP
FTP function can be enabled only when it is selected as a destination path. When the network is disconnected or does not work, you can save recordings and snapshots to the SD card by using Emergency (Local) function.
Step 1 Select Setting > Storage > Destination > FTP.

Step 2 Select the Enable checkbox to enable FTP function.

• There might be risks if the FTP function is enabled. Think twice before enabling the function.
• SFTP is recommended to ensure network security.
  Step 3 Configure FTP parameters.
  Table 5-47 FTP parameter description

exception, the recordings and snapshots will be stored on the local SD card.

Step 4 Click test to verify the username and password, and test whether FTP is connected to the Device.
Step 5 Click Save.
5.6.3.3 Local
SD card information is displayed in the local storage list. You can set it as read only or read & write.
You can also hot swap or refresh it.
Dual SD cards are supported by some devices. For such devices, the SD card first inserted is called
Local Disk 1, and the SD card inserted later is called Local Disk 2.

• If no recordings in both cards, the recording will be saved to Local Disk 1, and then saved to Local
  Disk 2 when Disk 1 is full.

• If there are recordings in both cards, the recording will be saved to the card with the latest recordings, and then saved to the other card when this card is full.
  Step 1 Select Setting > Storage > Destination > Local.

Step 2 Select the SD card to be set, and then perform the following operations as needed.

• Click Read Only to set the SD card to be read only.
• Click Read & Write to set the SD card to be read and write.
• Click Hot Swap to remove or insert the SD card when the Camera is running.
• Click Format to format the SD card.
  After formatting the SD card, all data on it will be cleared. Be cautious.

5.6.3.4 NAS
This function can be enabled only when NAS is selected as a destination path. Select NAS to store files on the NAS server.
Step 1 Select Setting > Storage > Destination > NAS.

S tep 2 Configure NAS setting parameters.
Table 5-48 NAS parameter description

function.

There might be risks if NFS or SMB is enabled. Think twice before enabling the function.

Server Address| The IP address of the NAS server.
Remote Directory| The destination path on the NAS server.

Step 3 Click Save.
5.6.4 Record Control
Step 1 Select Setting > Storage > Record Control.
Figure 5-144 Record control

Step 2 Configure record control parameters.
Table 5-49 Record control parameter description

by default.
Pre-event Record| Set the pre-recording time. For example, if you enter 5, when an alarm is triggered, the system reads the recording of the first 5 seconds in memory, and then records it into a file.

If alarm recording or motion detection recording occurs, if there is no recording before, the video data within N seconds before the recording is started will also be recorded into the video file.

●      Stop : The system stops recording when the disk is full.

●      Overwrite : The system overwrites the oldest files and keeps recording when the disk is full.

The data will be overwritten if the disk is full. Back up the file in time as needed.

Record Mode| You can select Auto , Manual or Off. Select Manual mode to start recording immediately, and select Auto mode to record within the schedule.
Record Stream| Select Main Stream or Sub Stream.

5.7 System Management
5.7.1 Device Settings
5.7.1.1 General
Step 1 Select Setting > System > General > General.

Step 2 Configure general setting parameters.
Table 5-50 Description of general setting parameter

5.7.1.2 Date & Time
Step 1 Select Setting > System > General > Date&Time.
Figure 5-146 Date & time

Step 2 Configure date &time parameters.
Table 5-51 Description of date & time parameter

Date Format

| Select the date format. Three formats are available: YYYY-MM-DD , MM- DD-YYYY and DD-MM-YYYY.
Time Format| Select the time format. Two formats are available: 24-Hour and 12- Hour.
Time Zone| Set the local time zone.
Current Time| The current time of the Device.
DST| Set the Start Time and End Time of DST in the Date format or Week format.
NTP| Select the NTP checkbox to enable the network time sync function.
Server| Set the address of the time server.  Set the network timing function of NTP server, and the Device time will be synchronized with the server time.
Port| Set the port number of the time server.
Interval| Set the synchronization interval of the Device and the time server.

5.7.1.3 Screen Off Settings
The function is available on select models.
You can set the screen-off time of the device display.
Step 1 Select Setting > System > General > Screen Off Settings.

Step 2 Set screen-off time.

• Never: The screen is never turned off.
• Custom: Customize the screen-off time.
  Step 3 Click Save.

Account Settings

5.7.2.1 Account
User management is only available for admin users.

• For Username and Group Name, the maximum length is 15 characters. Username can only consist of numbers, letters, underlines, dots and @; group name can only consist of numbers, letters and underlines.
• The password should consist of 8 to 32 non-blank characters and contain at least two types of characters among upper case, lower case, number, and special characters (excluding ‘ ” ; : &). The confirming password shall be the same as the new password. Set a high security password according to the prompt of password strength.
• The number of users and groups is 19 and 8 respectively by default.
• User management adopts a two-level method of group and user. Neither group names nor user names can be duplicated, and a user can only belong to one group.
• Users currently logged in cannot modify their own permissions.
• The user is admin by default. The admin account is defined as high privileged user.

5.7.2.1.1 Username
Select Setting > System > Account > Account > Username to enable anonymous login, add users, delete users, modify user passwords or perform other operations.
No permission is available for version information and other buttons except Relay-out, Mark, and Wiper Control on the Live interface for the time being.
Anonymous Login
Select the Anonymous Login checkbox, and you can log in to the Device anonymously without username and password after entering IP. Anonymous users only have preview permission in the permission list. In the anonymous login, click Logout to log in to the Device by using other usernames.
After Anonymous Login is enabled, the user can view audio and video data without authentication.
Think twice before enabling the function.
Adding Users
Add users in the group and set permissions.
As the default user with the highest authority, admin cannot be deleted.
Step 1 Click Add User.

Step 2 Enter Username and Password, confirm password, select Group Name, and then add Memo.
Step 3 Set Operation Permission and Restricted Login.

•  Operation Permission: Click Operation Permission, and then select the operation permission of the user as needed.
• Restricted Login: Click Restricted Login, and the interface shown in Figure 5-150 is displayed. You can control login to the Device by setting the IP Address, Validity Period and Time Range.
• Once the group is selected as needed, the user permission can only be a subset of the group, and cannot exceed its permission attributes.
• It is recommended to give less permissions to general users than advanced users.

Modifying Users
Step 1 Click corresponding to the user you want to modify.

Step 2 Modify user information.
Step 3 Click Save.
Modifying Password
Step 1 Select the Modify Password checkbox.
Step 2 Enter old password and new password, and then confirm password.
Step 3 Click Save.
Deleting Users
Click corresponding to the user to be deleted, and the user can be deleted.
Users/user groups cannot be recovered after deletion. Think twice before performing the operation.
5.7.2.1.2 Group Name
Select Setting > System > Account > Account > Group Name to add groups, delete groups, modify group passwords or perform other operations.

Configuring User Group
The default authorities of Admin group include live, playback, storage, file backup, user, system,  system info, manual control, maintenance, peripheral, PTZ, security, network, event and AV parameters; the default authorities of User group include live and playback. Table 5-52 Description of user group parameters

User

|

YES

|

NA

| Add, delete and check user/user group.

Live

|

YES

|

YES

| Real-time stream view.
Playback| YES| YES| Playback view.

System

|

YES

|

NA

| System time setting and more.

System Info

|

YES

|

NA

| Version information, system logs and more.
Manual Control| YES| NA| PTZ settings.
File Backup| YES| NA| File backup.

Storage

|

YES

|

NA

| Storage point configuration, snapshot recording time configuration, SFTP configuration and more.

Event

|

YES

|

NA

| Video detection settings, audio detection settings, alarm settings and more.

Network

|

YES

|

NA

| IP settings, SMTP settings, SNMP settings, AP Hotspot settings and more.

Peripheral

|

YES

|

NA

| External light, wiper and serial port settings.

AV Parameter

|

YES

|

NA

| Camera property settings, audio and video settings and more.

PTZ

|

YES

|

NA

| Preset settings, tour settings and more.

Security

|

YES

|

NA

| HTTPS settings, RTSP over TLS settings and more.

Maintenance

|

YES

|

NA

| Automatic maintenance settings and more.

•  Any user in the Admin group has User authority to modify group authority. The User group does not have this authority.
• The functions of the device correspond to the authority control respectively. Only user with specified authority can use corresponding function; the Admin group has all the authorities.
  Adding Groups
  For specific operations, refer to “5.7.2.1.1 Username”. Modifying Groups
  For specific operations, refer to “5.7.2.1.1 Username”. Deleting Groups
  For specific operations, refer to “5.7.2.1.1 Username”.

5.7.2.2 ONVIF User
On the web page, you can add ONVIF users, or modify existing users.
Procedure
Step 1 Select Setting > System > Account > Onvif User.

Step 3 Set the username and password, confirm password, and then select the group name.
Step 4 Click Save.
Related Operations

•  Click   to modify user information.
•  Click to delete users.

Safety

5.7.3.1 RTSP Authentication
Set the authentication method for media stream.
Step 1 Select Setting > System > Safety > RTSP Authentication.

Step 2 Select the Authorize Mode.
You can select from Digest, Basic and None. It is Digest by default.

• Click Default, and Digest is selected automatically.
  Select None, and “Non-authentication mode may have risk. Are you sure to enable it” prompt will be displayed. Think twice before selecting the mode.

• Select Basic mode, and “Basic authentication mode may have risk. Are you sure to enable it?” prompt will be displayed. Think twice before selecting the mode.

System Service

You can configure system service to ensure system security. Step 1 Select Setting > System > Safety > System Service.

Step 2 Configure system service parameters.
Table 5-53 Description of system service parameter

function is disabled by default.  It is recommended to disable SSH. If this function is enabled, there might be security risks.
Multicast/Broadcast Search| Enable this function, and when multiple users are viewing the monitoring screen simultaneously through network, they can find the Device through multicast/broadcast protocol.  It is recommended to disable the multicast/broadcast search function. If this function is enabled, there might be security risks.
Password Reset| You can enable Password Reset to perform security management. The function is enabled by default.If the function is disabled, you can only reset the password after restoring the Device to factory defaults through pressing the Reset button on the device.
CGI Service| You can access the Device through this protocol. The function is enabled by default.

It is recommended to disable the function. If this function is enabled, there might be security risks.

Onvif Service

| You can access the Device through this protocol. The function is enabled by default.  It is recommended to disable the function. If this function is enabled, there might be security risks.

Audio and Video Transmission Encryption

| Enable this function to encrypt the stream transmitted through the private protocol.

●      Make sure that the matched devices or software support video decryption function.

●      It is recommended to enable the function. If the function is disabled, there might be risk of data leakage.

Mobile Push| Push the alarm snapshot triggered by the Device to the mobile phone. The function is enabled by default.  It is recommended to disable the function. If this function is enabled, there might be security risks.
Private Protocol Authentication Mode| You can select Security Mode and Compatible Mode. Security mode is recommended. If you select compatibility mode, there might be security risks.

5.7.3.3 HTTPS
It is recommended to enable HTTPS service. If the service is disabled, there might be risk of data leakage.
Create certificate or upload signed certificate, and then you can log in through HTTPS with your PC.
HTTPS can ensure data security, and protect user information and device security with reliable and stable technology.
Step 1 Create certificate or upload the signed certificate.
● If you select Create Certificate, refer to the following steps.

1. Select Setting > System > Safety > HTTPS.

2. Enter the required information, and then click Create.
   The entered IP or domain name must be the same as the IP or domain name of the Device.

3. Click Install to install the certificate on the Device.

4. Click Download to download root certificate.
   Figure 5-160 Download root certificate

5. Select storage path, and then click Save.

6. Double-click the RootCert.cer icon.

7. Click Install Certificate.

8. Click Next, and then select Trusted Root Certification Authorities.

9. Click Next.

10. Click Finish.

12) Click Yes, and then click OK to complete the certificate installation.

● If you select Install Signed Certificate, refer to the following steps.

1. Select Setting > System > Safety > HTTPS.

2. Click Browse to upload the signed certificate and certificate key, and then click Upload.

3. Install the root certificate. For details, see 5) to 12) in Step1.
   Step 2 Select Enable HTTPS, and then click Save.
   The configuration takes effect after reboot.
   Figure 5-168 Reboot

Enter https://xx.xx.xx.xx in the browser to open the login interface. If no certificate is installed, a certificate error prompt will be displayed.

• If HTTPS is enabled, you cannot access the Device through HTTP. The system will switch to HTTPS if you access the Device through HTTP.
• The deletion of created and installed certificates cannot be restored. Think twice before deleting them.

5.7.3.4 Firewall
Set a firewall for the Device to prevent network attacks after the Device is connected to the network.
Step 1 Select Setting > System > Safety > Firewall.

Step 2 Select the type of network attack that the firewall resists. You can select Network Access, PING Prohibited, or Prevent Semijoin.
Step 3 Select Enable to enable Firewall function.
Step 4 Click Save.
5.7.4 Peripheral
The peripheral functions might vary with different models.
Step 1 Select Setting > System > Peripheral > Wiper.

Step 2 Configure wiper parameters.
Table 5-54 Description of wiper setting parameter

Mode

| Set the wiper mode. It is Manual by default.

In Manual mode, you need to manually start the wiper.

Interval Time| The time between wiper starting to wiper ending.

Working Duration

| Set the maximum duration of the wiper operating once in Manual

mode. The value ranges from 10 minutes to 1440 minutes.

Default

All information except IP address and user management will be restored to defaults. Think twice before performing the operation.
Select Setting > System > Default, and click Default to restore the Device.

Select the recovery mode.

• Default: All information except IP address and user management will be restored to defaults.
• Factory Default: The function is equivalent to the Reset button of the Device. All configuration information of the Device can be restored to the factory defaults, and the IP address can also be restored to the original IP address. After clicking Factory Default, you need to enter the password of admin user on the page displayed. The Device can be restored to factory defaults only after the system confirms that the password is correct.
• Only admin user can use this function.
• When the Device is restored to factory defaults, all information except the data in the external storage media will be erased. Delete data in external storage media by formatting and other methods.

Import/Export

When multiple devices share the same configuration methods, they can be quickly configured by importing and exporting configuration files.
Step 1 On the web page of one device, select Setting > System > Import/Export.

Step 2 Click Export to export the configuration file (.backup file) to the local storage path.
Step 3 Click Import on the Import/Export page of the Device to be configured to import the configuration file, and the Device will complete the configurations.

System Maintenance

5.7.7.1 Auto Maintain
You can select Auto Reboot or Auto Delete Old Files.

• If you select Auto Reboot, the frequency and time need to be set.
•  If you select Auto Delete Old Files, you need to set the time period for the files to be deleted.
  Step 1 Select Setting > System > Auto Maintain.

Step 2 Configure parameters of auto maintain.
Table 5-55 Description of auto maintain parameter

Auto Delete Old Files

| Select the checkbox to customize the time period for the files to be deleted. The value ranges from 1 day to 31 days. When you enable the function, The deleted files cannot be recovered. Are you sure to enable this function now? prompt will be displayed. Think twice before enabling the function.

5.7.7.2 Emergency Maintenance
By enabling emergency maintenance, you can fix most issues caused by upgrade and configuration.
Step 1 Select Setting > System > Auto Maintain > Emergency Maintenance.

Upgrade

Upgrade the system to improve device function and stability.
If wrong upgrade file has been used, restart the Device; otherwise some functions might not work properly.
Select Setting > System > Upgrade.

• File Upgrade: Click Browse, select the upgrade file, and then click Upgrade to upgrade the firmware. The upgrade file is in the format of *.bin.
• Online Upgrade
  1. Select the Auto-check for updates checkbox.
  This will enable the system to check for upgrade once a day automatically, and there will be system notice if any upgrade is available.
  We need to collect the data such as IP address, device name, firmware version, and device serial number to perform auto-check. The collected information is only used to verify the legitimacy of the Device, and push the upgrade notification.
  2. Click Save.
  Click Manual Check, and you can check for upgrade manually.

Information

You can view information such as version, online users, log, and life statistics.
5.8.1 Version
You can view information such as system hardware features, software version and release date.
Select Setting > Information > Version > Version to view the version information of current web interface.

5.8.2 Log Information
5.8.2.1 Log
Select Setting > Information > Log > Log to view the operation information of the Device and system information.

Table 5-56 Log parameter description

Start Time

| The start time of the log to be searched (January 1, 2000 is the earliest time).

End Time

| The end time of the log to be searched (December 31, 2037 is the latest time).

Type

| The log type includes All, System, Setting, Data, Event, Record, Account, Clear Log, and Safety.

Search

| Set the start time and end time of the log to be searched, select the log type, and then click Search. The searched log number and time period will be displayed.
Detailed Information| Click a log to display the details.
Clear| Clear all logs of the Device, and classified clearing is not supported.
Backup| Back up the searched system logs to the PC currently used by the user.

The data will be overwritten if the disk is full. Back up the data in time as needed.

Here are the meanings of different log types.

• System: Includes program launch, force exit, exit, program reboot, device shutdown/restart, system reboot, and system upgrade.
• Setting: Includes saving configurations, and deleting configuration files.
• Data: Includes disk type configurations, data erasing, hot swap, FTP state, and recording mode.
• Event (records events such as video detection, smart plan, alarm, and abnormality): Includes starting events, and ending events.
• Record: Includes file access, file access error, and file search.
• Account (records modification of user management, login, and logout): Includes login, logout, adding user, deleting user, modifying user, adding group, deleting group,and modifying group.
• Safety: Includes security-related information.
• Clear Log: Clearing logs.
  5.8.2.2 Remote Log
  Upload the Device operations to the log server.
  Step 1 Select Setting > Information > Log > Remote Log.

Step 2 Select Enable to enable remote log function.
Step 3 Set the IP Address, Port and Device Number of the log server.
Click Default to restore the Device to the default settings.
5.8.3 Online User
Select Setting > Information > Online User to view online users.

5.8.4 Life Statistics
Select Setting > Information > Life Statistics to view the life statistics of the Device.
The function is available on select models.

5.8.5 Battery Status
Select Setting > Information > Battery Status to view battery usage of the Device.
The function is available on select models.

5.8.6 Legal Information
Select Setting > Information > Legal Info to view legal information of the Device. Click Open Source
Software Notice to view the corresponding content.
The function is available on select models.

6 Alarm
You can select alarm types on the page. When the selected alarms are triggered, detailed alarm information will be displayed on the right side of the page. You can also select Prompt or Play Alarm Tone. When an alarm occurs, the alarm prompt or tone will be triggered.

Table 6-1 Description of alarm setting parameter

Alarm Type

|

Motion Detection

| Record alarm information in case of motion detection.
Disk Full| Record alarm information in case of full disk.
Disk Error| Record alarm information in case of disk error.

Video Tamper

| Record alarm information in case of video tampering.

External Alarm

| Record alarm information in case of an external alarm.
Illegal Access| Record alarm information in case of illegal access.

Audio Detection

| Record alarm information in case of audio detection.
IVS| Record alarm information in case of smart events.

Scene Changing

| Record alarm information in case of scene changing.

Security Exception

| Record alarm information in case of security exception.
Category| Parameter| Description
---|---|---

Operation

|

Prompt

| Select the Prompt checkbox. When you are not on the Alarm page, and the selected alarm event is triggered, the Relay-out button on the main menu will change to   , and the alarm information will be automatically recorded. After you click the Alarm menu bar, the button disappears.

If you are on the Alarm page, there will be no image prompt when the selected alarm event is triggered, but the corresponding alarm information will be recorded in the alarm list on the right.

Alarm Tone

|

Play Alarm Tone

| Select the checkbox, and then select the tone file path. When the selected alarm event is triggered, the selected tone file will be played to prompt you that an alarm event is triggered.
Tone Path| Customize the storage path for alarm tones.

Logout

Click Logout to log out, and the login page is displayed. Enter the username and password to log in again.
Figure 7-1 Login page

Appendix 1 Cybersecurity Recommendations

Mandatory actions to be taken for basic equipment network security:

1. Use Strong Passwords
   Please refer to the following suggestions to set passwords:
   ● The length should not be less than 8 characters.
   ● Include at least two types of characters; character types include upper and lower case letters, numbers and symbols.
   ● Do not contain the account name or the account name in reverse order.
   ● Do not use continuous characters, such as 123, abc, etc.
   ● Do not use overlapped characters, such as 111, aaa, etc.

2. Update Firmware and Client Software in Time
   ● According to the standard procedure in Tech-industry, we recommend to keep your equipment (such as NVR, DVR, IP camera, etc.) firmware up-to-date to ensure the system is equipped with the latest security patches and fixes. When the equipment is connected to the public network, it is recommended to enable the“auto-check for updates” function to obtain timely information of firmware updates released by the manufacturer.
   ● We suggest that you download and use the latest version of client software.

“Nice to have” recommendations to improve your equipment network security:

1. Physical Protection
   We suggest that you perform physical protection to equipment, especially storage devices. For example, place the equipment in a special computer room and cabinet, and implement well-done access control permission and key management to prevent unauthorized personnel from carrying out physical contacts such as damaging hardware, unauthorized connection of removable equipment (such as USB flash disk, serial port), etc.

2. Change Passwords Regularly
   We suggest that you change passwords regularly to reduce the risk of being guessed or cracked.

3. Set and Update Passwords Reset Information Timely
   The device supports password reset function. Please set up related information for password reset in time, including the end user’s mailbox and password protection questions. If the information changes, please modify it in time. When setting password protection questions, it is suggested not to use those that can be easily guessed.

4. Enable Account Lock
   The account lock feature is enabled by default, and we recommend you to keep it on to guarantee the account security. If an attacker attempts to log in with the wrong password several times, the corresponding account and the source IP address will be locked.

5. Change Default HTTP and Other Service Ports We suggest you to change default HTTP and other service ports into any set of numbers between
   1024–65535, reducing the risk of outsiders being able to guess which ports you are using.

6. Enable HTTPS
   We suggest you to enable HTTPS, so that you visit Web service through a secure communication channel.

7.  MAC Address Binding
   We recommend you to bind the IP and MAC address of the gateway to the equipment, thus reducing the risk of ARP spoofing.

8. Assign Accounts and Privileges Reasonably
   According to business and management requirements, reasonably add users and assign a minimum set of permissions to them.

9. Disable Unnecessary Services and Choose Secure Modes
   If not needed, it is recommended to turn off some services such as SNMP, SMTP, UPnP, etc., to reduce risks.
   If necessary, it is highly recommended that you use safe modes, including but not limited to the following services:
   ● SNMP: Choose SNMP v3, and set up strong encryption passwords and authentication passwords.
   ● SMTP: Choose TLS to access mailbox server.
   ● FTP: Choose SFTP, and set up strong passwords.
   ● AP hotspot: Choose WPA2-PSK encryption mode, and set up strong passwords.

10. Audio and Video Encrypted Transmission
    If your audio and video data contents are very important or sensitive, we recommend that you use encrypted transmission function, to reduce the risk of audio and video data being stolen during transmission.
    Reminder: encrypted transmission will cause some loss in transmission efficiency.

11. Secure Auditing
    ● Check online users: we suggest that you check online users regularly to see if the device is logged in without authorization.
    ● Check equipment log: By viewing the logs, you can know the IP addresses that were used to log in to your devices and their key operations.

12. Network Log
    Due to the limited storage capacity of the equipment, the stored log is limited. If you need to save the log for a long time, it is recommended that you enable the network log function to ensure thatthe critical logs are synchronized to the network log server for tracing.

13. Construct a Safe Network Environment
    In order to better ensure the safety of equipment and reduce potential cyber risks, we recommend:
    ● Disable the port mapping function of the router to avoid direct access to the intranet devices from external network.
    ● The network should be partitioned and isolated according to the actual network needs. If there are no communication requirements between two sub networks, it is suggested to use VLAN, network GAP and other technologies to partition the network, so as to achieve the network isolation effect.
    ● Establish the 802.1x access authentication system to reduce the risk of unauthorized access to private networks.
    ● Enable IP/MAC address filtering function to limit the range of hosts allowed to access the device.

References

• Free Dynamic DNS - Managed DNS - Managed Email - Domain Registration - No-IP
• 专业的云计算、动态域名服务提供商 - 公云PubYun

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>