LED LIGHTING HUT LEI-4361DMX 144W RGBW DMX Twinkle Wheel Fiber Optic LED Illuminator User Manual

LED LIGHTING HUT LEI-4361DMX 144W RGBW DMX Twinkle Wheel Fiber Optic LED

Illuminator

Accessories

• Fiber Connector ………………………… 1 PC
• Wireless Remote Controller……………1 PC (Optional)
• User Manual ………………………… . . . . . . 1 P C
• Signal Cable ………………………………1 PC (for DMX machine only)

Welcome to use LEI series of professional light engines.
Please read the manual carefully before using the light engine. If you have any questions concerning the operation or maintenance, please contact your wholesaler.

Safety Instruction

1. Make sure the Light Engine and Power Source have the same voltage;
2. Keep out of the rain or moist areas to avoid shock hazards;
3. Avoid to use at high ambient temperature ( >40℃);

CHAPTER 1 LEI-4361DMX

Technical Data

Installation dimension of the light engine(see Fig.1)

Light Engine Setup
There are three control modes for the LEI-Series DMX512 protocol Light Engine:

• DMX512 Signal Control Mode: DMX512 Signal is received from a DMX512 controller.
• Master/Slave Mode: One Light Engine is set as Master, while the rest light engines are set as Slaves. The master sends a control signal to the slave so that all the machines run the program synchronously.
• Audio Control Mode: Light engines are controlled by sound.

DMX 512 signal control mode
Address Code Setup
Press buttons “UP” and “DOWN” at the same time (maybe several times) until the digital display shows “ ”, then press the button “UP” or “DOWN” to select the address code. 001-505

DMX Channels: 8 Channels

• CH1:Red (256 level) CH2:Green (256 level)
• CH3:Blue (256 level) CH4:White
• CH5:Speed (256 level) CH6:Dimmer (256 level)
• CH7:Strobe/Program Speed CH8:Preset Program

Notice

1. For CH8, Only “P01-P15” are available, “P016-P21” are not available;
2. When CH8 is not “0”, CH1~CH4 are not usable, CH7 is preset programs speed;
3. When CH8 is “0”, CH1~CH6 are usable, CH7 is strobe

Master/Slave mode: The setting of Master/Slave

buttons at the same time for 3 seconds to unlock the menu for setting up.

2. Hold and press the button “UP”, at the same time to press the button“DOWN” to switch the menu.Then release both bottons.

3. Press either button of “UP” or “DOWN” to choose the right parameter.

4. After 60 seconds, the data will be saved and the menu locked.

5. When the display is on, the dot next to the third digit will flash

if there is any DMX signal coming in.

 | 2| ps. 1 -ps. 2| PS.1-PS.2 are audio control programs (when it display “PS.X”, press “UP/DOWN” to get into this menu)

MASTER

| 3| s. 00 -s. 07| Color wheel speed setup: total 8 levels:1/2RPM, 1RPM,2RPM,3RPM,4RPM,5RPM,8RPM,12RPM
 | 4|  | Adjusting of brightness: total 8 levels: d.00,d.10,d.20, d.35,d.50,d.70,d.85,d.99.(d.99.means100% brightness)
 | 5|  | r.on: Remote control is on, r.oF: Remote control is off.
Slave DMXReceiver| 6| 001-505|

DMX address,“001”-“505”are available

Notice

1. If you need the Master/Slaves to change color synchronously, please set all slaves into”001”;
2. If you need Master/Slaves to chase to change color, please set slaves into “009”,”017” and so on (add “8” one after another).

The connection of DMX Signal Control Mode(See Fig. 2)

The connection of Master/Slave Control Mode(See Fig. 3)

Signal cable and connector (See Fig.4)
2 Signal cable should be 2×0.5mm audio cable.

Wireless remote controller (See Fig.5)

Press the two buttons “UP” / “DOWN” beside the Display at the same time. When it displays, press either button of “UP” / “DOWN” to show  (the status of the remo control).
The remote function is on. 15-Key Remote Controller:

1. Program Selection: Press “PRO”, then press the digit key on the controller, “00”-“23”, to choose the desirable program, or you can use “ ”,“ ” to select.
2. Dimming: Press the key “DIM”, then press “ 0 ”-“ 7 ” to have the desirable brightness, or you can use “ ”,“ ” to adjust.
3. Speed of the color wheel: Press the key “SP”, then press “0”-”7” to adjust the speed, or you can use “ ”,“ ” to adjust.

Notice

1. Address codes of slaves (machines) are not adjustable under remote control status.
2. When you are selecting the program, only double-digit numbers on the controller are recognizable (e.g. 00, 01, 02…).

Attached Table

P.01

P.02

| White

Red

| P.09

P.1 0

| 6 colors skip

3 colors skip

| P.1 7

P.1 8

| 6 colors skip & chase

3 colors skip & chase

P.03| Green| P.1 1| 7 colors fade| P.1 9| 7 colors fade & chase
P.04| Blue| P.1 2| 6 colors fade| P.20| 6 colors fade & chase
P.05| Purple| P.1 3| 3 colors fade| P.21| 3 colors fade & chase
P.06| Yellow| P.1 4| 7 colors skip+7 colors fade| PS.1| 3 colors skip & audio control
P.07| Sky-B| P.1 5| 6 colors skip+6 colors fade| PS.2| 3 colors skip & audio control

Chapter 2 Installation of Fiber Optic

1. Connecting the fiber optic with the Light Engine: Solid Core fiber optic(see Fig. 1):
2. Cut the fiber to the specified length. The cross-section should be vertical to the fiber and keep clean and smooth.
3. Peel off 50-100mm of the PVC jacket of the fiber optic cable (not necessary if there is no PVC jacket). Be careful not to hurt the fiber optic.
4. Unscrew the PG Connector and insert the fiber optic cable into the PG Connector and Fiber Connector until the end of the cable is flush with the Fiber Connector. Screw tightly the PG Connector.
5. Insert the finished Fiber Connector into the Fixing Flange, and screw tightly the Screw.

Installation of the end part of the Multi-String fiber optic

1. Drill holes on the installing board according to the design. Then insert the fiber optic string into holes and fix it with epoxy glue. Trim the end of the fiber string to be flush with the board or at a required length. Fasten the other end of the fiber string to a harness and insert the harness into the PG Connector and Fiber Connector. Apply the hot knife to cut the fiber end flush with the Fiber Connector. (see Fig.2).
2. Insert the finished Fiber Connector into the Fixing Flange and screw tightly the Screw.
3. Commonly used installation method of fiber optic cable:

Side Lighting Fiber Optic:(see Fig.3)

End Lighting Fiber Optic

Documents / Resources

| LED LIGHTING HUT LEI-4361DMX 144W RGBW DMX Twinkle Wheel Fiber Optic LED Illuminator [pdf] User Manual
LEI-4361DMX 144W RGBW DMX Twinkle Wheel Fiber Optic LED Illuminator, LEI- 4361DMX, 144W RGBW DMX Twinkle Wheel Fiber Optic LED Illuminator, Twinkle Wheel Fiber Optic LED Illuminator, Wheel Fiber Optic LED Illuminator, Fiber Optic LED Illuminator, Optic LED Illuminator, LED Illuminator, Illuminator
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>