Pioneer TS-WX120A powered subwoofer Instruction Manual
- June 13, 2024
- Pioneer
Table of Contents
Pioneer TS-WX120A powered subwoofer
Be sure to read this instruction manual before installing this speaker.
WARNING
- Before starting the installation make sure to disconnect the vehicle’s negative(-) battery power cable. This will prevent possible electrical shock.
- When wiring this unit please use the supplied connecting cords. DO NOT remove the fuses. The protection circuit will not work in case of an emergency.
- TS-WX120A installed in the passenger compartment should be securely anchored in place.
- Before drilling any mounting holes check behind where you want to drill the holes to make sure you DO NOT drill into anything such as the gas lines, brake lines or electrical wiring.
- Do not install the TS-WX120A anywhere it can get wet
- Install the TS-WX120A in a location with good ventilation. Do not place anything on top of TS-WX120A to prevent airflow through the unit
- While driving keep your listening volume at a level that does not mask important outside traffic noises. such as emergency vehicles. etc.
- High sound levels may cause permanent hearing loss.
CAUTION
- This device is for 12-volt (-) negative ground. Please check your automobile to make sure it is this type.
- When routing leads and cords, secure them with cable retainers and electrician’s adhesive tape or shrink tubing wherever they may touch sharp edges. Keep all wiring away from hot surfaces or heater outlets to prevent short circuits.
- Refer to your car stereo’s operation manual as well when installing speakers in your car.
Note: If low-frequency noise exists in the head unit, noise may be amplified by TS-WX120A.
- Information Note for Customers in Russia and CIS countries.
If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
FEATURES
- Shallow & compact design for fitting under the seat or any small space
- Built-in high power 150 W MOSFET amplifier for powerful response & low distortion
- Powerful 20 cm x 13 cm woofer for rich & punchy bass
- A wired remote control included for easily adjustable bass sound
- Compatible RCA & speaker input for system application versatility
CONNECTIONS
Wiring Example 1 (Speaker line Input system)
- Connect the lead to a power supply terminal from the fuse box ‘M” which can provide a constant current level of more than 1 O A.
- This connection is made to the accessory connector in the car’s fuse unit from which over 2 A can be supplied.
- Speaker line input
- Connect firmly to a metal part of the car body. lmp<oper grounding wm cause this unit to operate abnormally.
Wiring Example 2 (RCA Input system)
- Connect the lead to a power supply terminal from the fuse box which can provide a constant current level of more than 1 O A.
- RCA cord (Not included)
- System remote control output
- RCA pre-out
- The system remote control input cord (blue cord included) supplies power to your unit. determining whether ii is ON or OFF. Wire the cord to the system remote control output of your deck, etc.
THE FINAL STEP OF THE INSTALLATION
Finish the installation by reconnecting the vehicle’s negative(-) battery lead.
CONTROLS AND THEIR USE
-
Power indicator
Lights up when power is turned on. -
Gain control
Use this control to set the desired gain level. -
Frequency control
Turn this knob to change the frequency during sound reproduction.
Set the knob to the bass setting of your choice (continuously variable from 50 Hz to 125 Hz). -
Phase switch
Use the switch to select the phase according to the system.
HOW TO INSTALL
Attaching cord clampers
How to attach the remote control
EXAMPLE OF MOUNTING
PARTS INCLUDED
SPECIFICATIONS
Speaker specifications
- Size: 201 mm X 129 mm
- High compliance, rolled edge
- Heat-resistant voice coil
- Strontium magnet: 484 g
Amplifier
- Max. Power output: 150 W (80 Hz. 35 % THD)
- DIN output power (DIN45324, 80 Hz, 2.0 +B=14.4 V): 70 W
- INPUT LEVEL (at Gain Max)
- (RCA): 100 mV+100 mV/20 kQ
- (Speaker line): 2 V+2 V/5 kQ
- Power source: DC 14.4 V (10.8 V to 15.6 V allowable)
- Max. current consumption: 7 A
- Grounding: Negative ground
- Speaker system: Sealed design
- Cabinet material: High-density compound resin
- Sensitivity: 98 dB
- Size: 280 mm (W) X 200 mm (D) X 70 mm (H)
- Weight (including accessory parts): 3.60 kg
- Gross weight (including packaging): 3.80 kg
Note: Specifications and the design are subject to possible modification without notice due to improvements.
PIONEER CORPORATION
- Address: 1-1, Shin-ogura, Saiwai-ku, Kawasaki-Shi, Kanagawa 212-0031 JAPAN/JAPON
- Phone :+7(495)956-89-01
- Phone: TEL : 55-9178-4270
- Copyright: © PIONEER CORPORATION 2014
- Note: PRINTED IN CHINA IMPRIME EN CHINE (TRD1434-NFMT)
FAQs
What is the Pioneer TS-WX120A powered subwoofer?
The Pioneer TS-WX120A is a powered subwoofer designed to provide powerful bass in vehicles. It comes with a built-in high-power 150 W MOSFET amplifier and a 20 cm x 13 cm woofer.
How do I finish the installation process?
Complete the installation by reconnecting the vehicle's negative(-) battery lead.
How can I control the sound from the subwoofer?
The subwoofer comes with a power indicator, gain control, frequency control, and phase switch. You can adjust these as per your listening preferences.
Are there any notes regarding the product's disposal?
If you need to dispose of this product, ensure it doesn't mix with general household waste. There's a separate collection system for used electronic products in line with legislation that mandates proper treatment, recovery, and recycling.
Where is the Pioneer Corporation located?
The address for Pioneer Corporation is 1-1, Shin-ogura, Saiwai-ku, Kawasaki- Shi, Kanagawa 212-0031, JAPAN/JAPON.
How can I contact Pioneer Corporation for queries related to the TS-WX120A?
You can reach Pioneer Corporation at +7(495)956-89-01 or TEL: 55-9178-4270.
What type of battery does the TS-WX120A support?
The device is designed for a 12-volt(-) negative ground. Please verify your automobile’s configuration before installation.
I noticed a low-frequency noise when connected to the head unit. What could be the reason?
If low-frequency noise exists in the head unit, it might be amplified by the TS-WX120A. You may need to check the connections or consult with the head unit manufacturer for solutions.
What precautions should I take during wiring?
When routing leads and cords, make sure to secure them properly. Use cable retainers and electrician's adhesive tape or shrink tubing to keep them away from sharp edges or hot surfaces.
How do I connect the TS-WX120A using the Speaker Line Input System?
Connect the lead to a power supply terminal from the fuse box that can provide a constant current level of more than 10 A. Make sure to establish a firm grounding to a metal part of the car body.
How do I connect the TS-WX120A using the RCA Input System?
You'll need to connect the lead to a power supply terminal from the fuse box which can provide a current level of more than 10 A. An RCA cord (not included) is required for this setup.
How can I adjust the bass setting?
You can use the Frequency control knob to adjust the bass setting. This allows you to change the frequency continuously from 50 Hz to 125 Hz.
Download This PDF Link:Pioneer TS-WX120A powered subwoofer Instruction Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>