SENCOR SWK 2190WH Variable Temperature Electric Kettle User Manual
- June 13, 2024
- SENCOR
Table of Contents
- SENCOR SWK 2190WH Variable Temperature Electric Kettle User Manual
- SENCOR SWK 2190WH Variable Temperature Electric Kettle
- Important safety instructions
- READ CAREFULLY AND STORE FOR FUTURE USE.
- Warning:
- Warning:
- Attention:
- ELECTRICAL SAFETY
- Attention:
- Note:
- Attention:
- Note:
- Note:
- Attention:
- Attention:
- 1. Removing limescale deposits
- 1. Cleaning the outer surface
- Attention:
- For business entities in European Union states
- Disposal in other countries outside the European Union.
SENCOR SWK 2190WH Variable Temperature Electric Kettle User Manual
SENCOR SWK 2190WH Variable Temperature Electric Kettle
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
-
This appliance may be used by children 8 years of age and older and by persons with physical or mental impairments or by inexperienced persons, if they areproperly supervised or have been informed about how to use the appliance in a safe manner and understand the potential dangers.
-
Children must not play with the
-
Cleaning and maintenance performed by the user must not be performed by children unless they are older than 8 years of age and under
-
Keep the appliance and its power cord out of reach of children younger than 8 years of
-
In the event that the power cord is damaged, have it repaired at a professional service centre to prevent causing a dangerous It is forbidden to use the appliance if it has a damaged power cord.
-
This appliance is designed for domestic use and similar locations such as:
- kitchens in stores; offices and other workplaces;
- in agriculture;
- for guests of hotels, motels and other similar locations;
- in bed and breakfast
-
Never wash the appliance under running water or submerge it in water or another
-
If the electric kettle is overfilled, then boiling water could splash
Warning:
Do not open the lid of the kettle when it is running and while water is boiling.
If the lid position can be adjusted, always locate it so that the steam flows away from the handle.
- Make sure that no water or any other liquid splashes on the power plug or the power socket, and that the hot
steam emitted from the appliance is also kept away. If this, nevertheless, occurs, disengage the circuit breaker of the power socket and then carefully dry the power socket and the power plug before further use.
- The surfaces of the appliance that come into contact with food must always be cleaned according to the instructions in this user’s
Warning:
Incorrect use may lead to injuries.
- The surface of the heating element retains residual heat after
Attention:
Hot surface.
ELECTRICAL SAFETY
- Before connecting the kettle to a power socket check that the voltage stated on the rating label matches the electrical voltage in the
- Connect the kettle only to a properly grounded
Attention:
This kettle is not designed to be controlled using a programmed device, external timer switch or remote control.
- Never use the kettle in the near vicinity of a bath, shower or swimming
- Do not wash the kettle or its base under running water and do not submerge it or its base in water or another liquid.
- Always disconnect the kettle from the power socket if you will not be using it or before moving or cleaning
- Ensure that the power cord does not come into contact with water or
- Take care not to spill water on to the connector when placing the kettle on to the base stand and when taking it off the base
- Do not place heavy items on the power Make sure that the power cord does not hang over the edge of a table and that it is not touching a hot surface.
- Do not disconnect the kettle from the power socket by pulling on the power This could damage the power cord or the power socket. Disconnect the cord from the power socket by gently pulling the plug of the power cord.
- If the power cord is damaged, have it replaced at a specialised service It is forbidden to use the kettle if it has a damaged power cord or plug.
- To avoid the danger of injury by electrical shock, do not repair the kettle yourself or make any adjustments to All repairs of this kettle should be carried out at an authorised service centre. Tampering with the appliance during the warranty period may void the warranty.
SAFETY DURING USE
-
Do not place the kettle on window sills or on unstable Always place the kettle on a stable, even and dry surface.
-
Only use the kettle with the base that was supplied with Do not use the base supplied with this kettle for other types of kettles.
-
Use the kettle only for boiling
-
Although the kettle is protected against damage caused by accidentally turning it on without water, do not use it Incorrect use may negatively affect its working order and lifetime.
-
Always take the kettle off the base stand before filling
-
Check that the lid is securely closed before starting the Do not open the lid or handle it in any way while the water is boiling.
-
The body of the kettle is heated up while water is Do not touch the hot surface. This could cause skin burns. Use the handle for lifting and carrying the kettle.
-
Do not place any items or kitchen utensils (e.g. spoons for stirring and serving food) into the kettle while it is boiling water or maintaining a temperature (depending on the kettle model).
-
Pay extra attention when handling a kettle filled with hot
-
Be especially careful when pouring water out of the kettle to avoid scalding by the boiling water or
-
Do not place the kettle on an electric or gas stove or in its vicinity, do not place it in the vicinity of an open fire or an appliance that is a source of
-
Clean it according to the instructions in chapter Cleaning and
-
Do not use the kettle when it is not functioning correctly or after it has fallen on the floor, been submerged in water or is showing visible signs of damage or if Hand it over to an authorised service centre for inspection or repair.
-
Prior to using this appliance, please read the user’s manual thoroughly, even in cases, when one has already familiarised themselves with previous use of similar types of Only use the appliance in the manner described in this user’s manual. Keep this user’s manual in a safe place where it can be easily retrieved for future reference.
-
We recommend saving the original cardboard box, packaging material, purchase receipt and responsibility statement of the vendor or warranty card for at least the duration of the legal liability for unsatisfactory performance or quality. In the event of transportation, we recommend that you pack the appliance in the original box from the
DESCRIPTION OF THE KETTLE
A1 Open lid button
A2 Lid
A3 Spout
A4 Filtration strainer (cannot be removed)
A5 Water level mark
A6 Base with a central connector
A7 Control panel
A8 Handle
A9 LED light for the inside of the kettle
DESCRIPTION OF THE CONTROL PANEL
- 50°C – dark green (baby porridge)
- 70°C – blue (green tea)
- 80°C – violet (white tea)
B1 Temperature setting LED indicators
B2 On/Off button
B3 **** Set temperature button
– 50, 70, 80 or 90 °C.
- 90°C – light green (instant coffee)
- 100°C – red (black/fruit/herbal tea)
- When the water is heated to the set temperature, the kettle will turn
**BEFORE FIRST USE OF THE KETTLE**
- Remove all wrapping material from the kettle and its base A6.
- Fill the kettle with clean water up to the maximum water mark. Boil the water and empty the contents of the kettle. Repeat this process 2 to 3
Note:
To boil water in the fast boil kettle proceed according to the instructions in chapter Using the kettle.
- Now the kettle is ready for
USING THE KETTLE
- Set the desired length of the power Push the power cord into the groove in the base A6. Place the base A6 on a stable, even and clean surface.
- Press button A1 to open the lid A2 , then fill the kettle with the required amount of water. The water level must reach at least the minimum mark (0.5l) and must not exceed the maximum mark (2l). After filling it, close the lid A2 and make sure that it is secured in the closed
Attention:
Do not fill the kettle when it is placed on the base A6.
When filling the kettle, there is a risk of water splashing out.
- Place the kettle on the base A6 and insert the power cord plug into a power When the power cord is connected to a power
socket, a short beep will be made and all the LED indicators B1 and the
LED light A9 will light up for an instant and another beep will be
off automatically. Two beeps are made and the LED light A9 will turn off.
LED indicator B1 remains lit for approximately one minute after it is
turned off. Then it turns off and the kettle switches to the stand-by mode.
Note:
If you set a temperature using button B3 and then do not press button
B2 to start the water heating process, after 15 seconds the kettle will
switch to the stand-by mode and the respective LED indicator B1 will turn
off.
The temperature setting can be changed while the appliance is running.
The process of heating water to a set temperature can be stopped at any time
by again pressing button B2.
If you set a temperature that is lower than the current temperature of the
water inside the kettle, a beep will be made after button B2 is pressed
and the kettle will turn off automatically.
Keep warm mode
- This mode is usually used when you wish to heat water to a required temperature and then maintain it at this temperature, or when you wish to boil water and then keep it
- Use button B3 to select the required temperature 50, 70, 80, or
- 90 °C. The respective LED indicator B1 will be lit. Press button B2 and hold it down for approx. 3 seconds. The respective LED indicator B1 will start flashing, the coloured LED light A9 will be lit as describedin point 4.2 and the process of heating water to the set temperature will start. When the set temperature is reached, two beeps are made and the kettle automatically switches to the keep warm mode. In this mode, the heating element automatically switches on andoff to maintain the set temperature. The keep warm mode ends automatically after 30 minutes. Two short beeps are made, the LED light A9 and the respective LED indicator B1 will turn off, and the kettle will switch to the stand-by mode
- Using the above described method, it is possible to set the keep warm mode after previously boiling or heating water according to described points 4.1 and 4.2. If, for this mode, you set a temperature
that is lower than the current water temperature inside the kettle, two beeps will be made when the kettle is started. This signals that the set temperature has already been reached. Water will cool down to the set temperature and will then be maintained at this temperature. The keep warm mode ends automatically afterminutes.
- To quickly switch the kettle from the stand-by mode to the keep warm mode, press and hold down button B2 for 3 seconds. Water will be maintained at a temperature of 50 °C.
Note:
If you set a temperature using button B3 and then do not press button
B2 to start the maintain set temperature mode, after 15 seconds the kettle
will switch to the stand-by mode and the respective LED indicator B1 will
turn off.
It is not possible to change the set temperature in the keep warm mode.
The keep warm mode can be stopped at any time by pressing button B2.
Attention:
If the kettle is not located on the base A6 , the buttons on the control
panel A7 will not react to being pressed.
Lifting the kettle off the base will cancel all previous settings. When the
kettle is placed back on to the base A6 , a short beep will be made and
all the LED indicators B1 and the LED light A9 will light up for an
instant and another beep will be made. The kettle will then again switch to
stand-by mode and is again ready for use.
This kettle is not calibrated for scientific or laboratory purposes. The
actual water temperature may differ by±5 °C from the set water temperature.
Attention:
Do not turn on the kettle when it is empty. Incorrect use may negatively affect its lifetime. If you accidentally turn on the kettle without water inside, after a short time a sound will be made, the LED light A9 will turn off and the kettle will turn off. Wait until the heating element cools down. This is indicated by a sound and all the LED indicators B1 and the LED light A9 turning on for an instant. Then the kettle will switch to stand- by mode and is again ready for use.
- Pour the boiled or heated water into a prepared container, cup or Make sure that the kettle remains in a vertical position when it is carried, particularly if it is filled all the way up to the maximum mark.
- If you wish to open the kettle to refill it, be especially careful when opening the lid A2 to avoid scalding by the escaping
- After you finish using it, disconnect the power cord from the power Empty the kettle and allow it to cool down.
CLEANING AND MAINTENANCE
1. Removing limescale deposits
- Limescale deposits inside the kettle may negatively affect its lifetime, so it is important to regularly remove it based on how frequentlythe kettle is used. During standard use (3 to 5 times per day), we recommend water scale deposits be removed:
- once per month in areas with hard and very hard water;
- once every two to three months in areas with soft and medium hard
- To remove limescale deposits it is possible to use:
- 8% white vinegar, generally available in Fill the kettle with 1 litre of water and ¼ litre of vinegar. Bring the solution to a boil and leave it to act in the kettle for 2 hours. Then empty the kettle and before further use, boil clean water in it four to five times.
- citric Boil 1.5 l of water in the kettle, into the boiled water, add 30 g of citric acid and allow the solution to act for about 30 minutes. Then empty the kettle and before further use, boil clean water in it four to five times.
1. Cleaning the outer surface
- Before cleaning, disconnect the power cord from the power Empty all the contents from the kettle and allow the kettle to cool down.
- To clean the external parts of the kettle, use a dry cloth or a cloth lightly dipped in a weak solution of neutral kitchen detergent. After applying the detergent, wipe the surface with a lightly damp cloth and then wipe
- To clean the base A6 , use only a dry
- For cleaning, never use steel wool, cleaning products with an abrasive effect, petrol and other
Attention:
Do not wash the kettle or its base A6 under running water and do not submerge it or its base A6 in water or another liquid.
TECHNICAL SPECIFICATIONS
Rated voltage range…………………………………………….. −240 V
Rated frequency…………………………………………….. 50/60 Hz
Rated power input……………………………………… 1 850–2200 W
Nominal capacity……………………………………………………. 2l
We reserve the right to change text and technical specifications.
**INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED
PACKAGING MATERIALS**
Dispose of used packaging material at a site designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on products or original documents means that used electric or
electronic products must not be added to ordinary municipal waste. For proper
disposal, renewal and recycling, hand over these appliances to determined
collection points. Alternatively, in some European Union states or other
European countries you may return your appliances to the local retailer when
buying an equivalent new appliance. Correct disposal of this product helps
save
valuable natural resources and prevents potential negative effects on the
environment and human health, which could result from improper waste disposal.
Ask your local authorities or collection facility for more details. In
accordance with national regulations penalties may be imposed for the
incorrect disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic equipment, ask your retailer or supplier for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this
product, request the necessary information about the correct disposal method
from the local council or from your retailer.
This product meets all the basic requirements of EU directives related to it.