KARCHER HD 585 High Pressure Cleaner Instruction Manual

June 13, 2024
Karcher

KARCHER HD 585 High Pressure Cleaner

Product Information

The HD 585 is a high pressure cleaner designed for efficient and powerful cleaning. It comes with a range of features and components to ensure safe and effective operation.

Symbols on the Machine

  • The appliance must not be directly connected to the public drinking water network.
  • The high pressure jet must not be directed at persons, animals, live electrical equipment, or at the appliance itself.
  • Protect the appliance against frost.

Grounding and 3-pin Plug
The HD 585 is equipped with a 3-pin plug that ensures user safety. The housing is connected to the central pin of the plug, which is in direct contact with the ground wire of the mains. It is important to follow the installation instructions regarding supply voltage and grounding.

Technical Data

  • Power Connection Voltage : 230V
  • Type of Current: 1~50
  • Connected Load : 2.2 kW
  • Mains Fuse (Slow): 16A
  • Extension Cable 10m : 1.5mm²
  • Extension Cable 30m : 2.5mm²
  • IP Code : IPX5
  • Protection Class : I
  • Water Connection
    • Supply Temperature (Max ): 60°C
    • Supply Rate (Min): 600 l/h
    • Supply Hose Length (Min ): 25m
    • Supply Hose Diameter (Min ): 21mm
    • Supply Pressure (Min-Max ): 120/12 bar/MPa
    • Flow Rate : 8.33 l/min
  • Detergent Intake
  • Recoil Force of Hand-held Spray Gun at Operating Pressure (Max ): 15N
  • Noise Level (DIN 45 635) : 81 dB(A)
  • Nozzle Size
  • Dimensions and Weight
    • Length : 420mm
    • Width : 180mm
    • Height : 260mm
    • Weight : 15.5kg

Product Usage Instructions

Before using the HD 585 high pressure cleaner, please read the following instructions

Safety Instructions

  1. Read and strictly observe the Safety Instructions for High Pressure Cleaners (5.951-949) provided with the product.

Assembly

  1. Refer to the manual for the assembly diagram and identify the numbered components.
  2. Attach the Anthracite Arms (Qty: 1) to the Anthracite Frame (Qty: 1) using the provided Screw M6x30 (Qty: 2).
  3. Attach the Knob M6 (Qty: 2) to the Anthracite Frame (Qty: 1).
  4. Install the Zinc Axle (Qty: 1) onto the Anthracite Frame (Qty: 1).
  5. Attach the Wheels (Qty: 2) to the Zinc Axle (Qty: 1) and secure them with the Wheel Caps (Qty: 2).

Operation

  1. Ensure that the appliance is not directly connected to the public drinking water network.
  2. Do not direct the high pressure jet at persons, animals, live electrical equipment, or at the appliance itself.
  3. Protect the appliance against frost.

Power Connection

  1. Ensure that the power supply voltage indicated on the label of the washer’s power cord matches the outlet where it will be connected.
  2. Connect the plug to an outlet according to NBR 14136 and make sure the outlet is in perfect condition.
  3. Remove the plug from the outlet before maintenance or cleaning the device.
  4. Keep all electrical connections dry and without contact with water and/or wet surfaces.
  5. Never remove the plug grounding pin or use adapters that eliminate the plug grounding pin.
  6. Do not use an adapter to connect to a 10A plug or use adapters or t-type connectors.

Cables and Extension

  1. If using an extension, ensure it meets the specifications for wire gauges and the amount of wires and pins as described in the manual
  2. Do not work under bad weather conditions.
  3. Never use an extension that does not allow the use of the plug grounding pin.
  4. Do not transport the equipment by dragging it through the hose or power cord.

For more detailed instructions and information, refer to the HD 585 Instructions Manual.

Please read these operating instructions before starting and strictly observe the “Safety Instructions for High Pressure Cleaners (5.951-949)“.

POS. Description / Qty

  1. Anthracite Arms 1
  2. Screw M6x30 2
  3. Knob M6 2
  4. Anthracite Frame 1
  5. Screw M5x35 3
  6. Zinc Axle 1
  7. Wheel  2
  8. Clamping Washer  2
  9. Wheel cap 2

Starting

  1. High pressure hose
  2. Pistol
  3. Spear
  4. Nozzles
  5. Safety Lock
  6. Trigger
  7. High pressure output
  8. Water inlet (suction) with filter
  9. Water inlet coupling for ½inch hose 10 – Detergent suction hose with filter 11 – Switch (ON/OFF)
  10. Electric cable with plug
  11. Threaded coupling
  12. Turbo nozzle (optional)

Unpacking the unit

  • If, while unpacking, you discover damage has been caused in transit, please inform your dealer immediately.
  • Do not simply discard the packing materials with the house-hold waste. Take the packing materials to the appropriate collection areas for recycling. Attaching accessories
  • Connect the spray lance and spray gun.
  • Attach the nozzle top
  • Tighten all union nuts by hand.

Connecting the power supply

  • See technical data of connected values.
  • Check whether the voltage shown on the rating plate corresponds to that of the power source.

Note: If you are using an extension cable, it should always be completely unwound from the cable drum and have a sufficient cross-sectional area: see “Technical Specifications

The use of cable reels that ensure that the sockets are at least 60mm above the ground is recommended.

Connecting the water supply

  • See Technical Data for connected values.
  • Connect a water supply hose (not supplied) to the appliance and the water pipe. Starting
  • Turn on the appliance by pressing the appliance switch. Turn off by pressing the appliance switch again Purpose
  • Use the appliance to clean machines, vehicles, buildings, tools, etc.
  • Clean facades, patios, garden implements, etc. with the high-pressure spray only, i.e. without detergent.
  • Engines must only be cleaned in places which have appropriate oil traps (protection of the environment).
  • If the machine is used at petrol stations or in other hazardous areas, the appropriate safety regulations must be observed.
  • For stubborn dirt, we recommend use of the dirt blaster which is available as an optional accessory Symbols on the machine

The appliance must not be directly connected to the public drinking water network.
The high pressure jet must not be directed adpersons, animals, live electrical equipment orat the appliance itself.

Protect the appliance against frost.

Operation

Deaerating the unit

  • Open the water supply.
  • To vent the unit, unscrew the nozzle and leave the unit running until the water exits with no air bubbles.
  • Switch off the unit and screw the nozzle back on. Operating with high pressure
  • Release safety latch on handgun and press lever.
  • Switch on unit.

Note: This unit is equipped with a pressure switch. The motor only starts up when the lever on the handgun is pressed.

Selecting type of iet

  • High-pressure fan jet (25°) for large areas of dirt
  • Low-pressure fan jet for use with detergents or cleaning at low pressure

Change nozzle only when handgun is closed.

  • Always direct high-pressure jet at object being cleaned from a greater distance first of all, in order to prevent damage if pressure is too high. Operating with detergents
  • Use low-pressure nozzle.
  • Suspend the detergent hose in the detergent container (not included).
  • In the interest of environmental protection, we recommend that you use detergents sparingly. Observe dosage recommendations shown on label on detergent canister.
  • We provide a specialized programme of deter- gents and other cleaning products, which gua- rantee trouble-free operation of your cleaner. Please ask for advice or send for our catalogue or information sheets with details about the cleaning agents.
  • We recommend the following cleaning methods
    • Step 1: Loosening dirt Spray on detergent sparingly and leave for 1-5 minutes.
    • Step 2: Removing dirt Spray off the loosened dirt with the high-pressure spray.
  • The appliance should be rinsed clean after detergent has been used. To do this, suspend the detergent suction hose in a container of clean water, and run the pump for approx. 1 minute. Interrupting operation
  • If you release the trigger of the spray gun, the appliance switches off. If the trigger is pulled again, the appliance switches on again.

Switching off the unit

  • Switch off the unit and pull the electric plug out of the socket.
  • Close the water supply.
  • Squeeze the lever on the spray gun until the unit has depressurized.
  • Secure the lever on the spray gun against unintentional opening. Transporting the unit
  • The unit is equipped with a trolley which enable it to be moved over longer distances more easily.

Care and Maintenance

  • Clean the filter on the detergent suction hose.
  • Clean the high-pressure nozzle. Remove dirt from the nozzle hole with a needle, and rinse with water from the front.
  • Clean the strainer in the water connection. It can be easily removed with a flat-nosed pliers
  • If the connection lead is damaged it must be replaced by an original spare set. Frost Protection
  • Frost will destroy an appliance which has not been completely emptied of water. Ideally, the appliance should be stored in a frost-free room

Troubleshooting

Note: Disconnect the appliance from the power mains before all repair work. Only authorized customer service personnel may inspect electrical components.

In this chapter, we would like to give you some hints on dealing with malfunctions yourself. In all other cases or in the case of electrical faults, please contact the authorized customer service.

Appliance does not Work

  • Check the mains voltage.
  • Check the connector cable for damage.
  • If the motor overheats, allow it to cool down for a few minutes. Then switch back on again. Appliance does not reach Operational Pressure
  • Use high-pressure nozzle.
  • Clean/renew nozzle.
  • Bleed the air from the appliance. (- Suction 2.)
  • Clean the strainer in the water connection.
  • Check the inlet water flow rate.
  • Check all inlet pipes to the pump for leaks or blockage. Strong Pressure Fluctuations
  • Clean the high-pressure nozzle. Remove dirt from the nozzle hole with a needle, and rinse with water from the front. Pump Leaks
  • 3 drops per minute are permissible. In the case of more serious leakage, you should contact the authorized customer service. No Detergent Suction
  • Use low-pressure nozzle.
  • Clean the detergent suction hose with filter, and check for leaks.

General Information

Safety inspection You may arrange for a safety inspection with your Kärcher dealer. Your dealer will be glad to advise you.

Service contract
You may also take out a service contract with your dealer. The safety inspection is included in the service contract. Your dealer will be glad to advise you.

Safety Equipment
When the hand-held spray gun is closed, the overflow valve switches off the appliance via a pressure-operated switch. The overflow valve is also a safety device against exceeding the maximum allowable working pressure. The overflow valve and the pressure-operated switch protect your appliance. In the case of badly functioning. contact your nearest authorized customer service centre.

Guarantee
The terms of guarantee issued by our competent distribution company are valid in every country. Ifthe appliance malfunctions in any way, we shall rectify the fault free of charge within the period of guarantee, provided the cause can be attributed to faulty material or a manufacturing error. In the event of a claim on the guarantee, please consult your dealer with accessories and receipt of purchase or contact your nearest authorized customer service centre.

Grounding and 3-pin plug

RISK OF ELECTRIC SHOCK

Electrical Connection
Your washing machine comes with a plug that meets the new Brazilian standard for plugs and must be connected to an outlet according to NBR 14136. Use an exclusive outlet in perfect condition to connect the device.
Check that the power supply voltage indicated on the label of the washer’s power cord is the same of the outlet where it will be connected.

  • This washing machine is comes with a 3-pin plug. The housing is connected to the central pin of the plug, which is in direct contact with the ground wire of the mains, increasing the user’s safety.
  • Pay close attention to the installation instructions, especially regarding supply voltage and grounding.
  • Remove the plug from the outlet before maintenance or cleaning the device.
  • Keep all electrical connections dry and without contact with water and/or wet surfaces. Never remove the plug grounding pin.
  • Do not use adapters that eliminate the plug grounding pin.
  • Never use an adapter to connect to a 10 A plug. Never use adapters or t-type connectors.
  • Do not attempt to plug the 3-pin plug into an outlet not in compliance with the NBR 14136.
  • Connect the plug only to properly grounded outlets.
  • Before connecting the washing machine to the mains, make sure that the high pressure washing machine on/off button is in the off position.
  • To turn off the high pressure washing machine, never pull the power cord, pull it only by the plug to avoid damage. Remove the plug from the outlet before maintenance or cleaning the high pressure washing machine.
  • Failure to follow these instructions may be life threatening, cause fire or electric shock.

Grounding and 3-pin plug

Cables and Extension
If you need to use an extension, make sure it meets the specifications for wire gauges and the amount of wires and pins, as described in this manual.

  • Never use an extension that does not allow the use of the plug grounding pin.
  • Do not transport the equipment by dragging it through the hose or power cord.
  • Do not work under bad weather conditions.

Technical Data

  HD 585

Power Connection
Voltage| 230| 220| 120| V
Type of current| 1~50| 1~60| 1~60| Hz
Connected load| 2,2| 2,2| 1,5| kW
Mains fuse (slow)| 16| 16| 16| A
Extension cable 10 m| 1,5| 1,5| 1,5| mm²
Extension cable 30 m| 2,5| 2,5| 2,5| mm²
IP Code| IPX5| IPX5| IPX5| –
Protection Class| I| I| I| –
Water Connection|  |  |  |
Supply temperature (max)| 60| 60| 60| °C
Supply rate (min)| 600| 600| 600| I/h
Supply Hose|  |  |  |
– lenght (min.)| 7,5| 7,5| 7,5| m
– diameter (min.)| ½| ½| ½| in
Supply pressure (min-max)| 2/0,2 –

12/1,2

| 2/0,2 –

12/1,2

| 2/0,2 –

12/1,2

| bar/MPa
Performance data|  |  |  |
Pressure (máx.)| 120/12| 120/12| 107/10,7| bar/MPa
Operation pressure| 110/11| 110/11| 72/7,2| bar/MPa
Flow rate| 500

8,33

| 500

8,33

| 400

6,7

| I/h L/min
Detergent intake| 25| 25| 25| I/h
Recoil force of hand-held spray gun at operating pressure (max.)| 21| 21| 15| N
Noise Level (DIN 45 635)| 81| 81| 81| dB(A)
Nozzle Size| 038| 038| 034| –
Dimensions and Weight|  |  |  |
Lenght| 420| 420| 420| mm
Width| 180| 180| 180| mm
Height| 260| 260| 260| mm
Weight| 15,5| 15,5| 15,5| kg

ARGENTINA
Kärcher S.A.

  • Colectora Este Panamericana KM 38.7 (Esq. Vicente Lopez) CP 1621 Benavidez Buenos Aires – Argentina.
  • +54 11 4748 5000

BOLIVIA

  • Kärcher Bolivia S.R.L
  • Avenida Banzer y KM 8
  • Comercial El Remanso – Santa Cruz Bolivia +591 (3) 3416111

CHILE

  • Kärcher Chile
  • Av. Los Libertadores 16.500 Nº 1-A-1, Colina
  • Chile
  • (+56 2) 23806100

COLOMBIA

  • Kärcher SAS
  • Av. Calle 116 No. 15 B 39 Bogotá
  • Colombia
  • 571 – 7 45 83 83

ECUADOR

  • Karcher Ecuador S.A.
  • Av. Juan Tanca Marengo km 3, Ciudadela Urdenor 2 Esquina Guayaquil
  • Ecuador
  • (593) 4600-5867 y (593) 4603-2401

MÉXICO

  • Karcher México
  • Circuito Poetas 68
  • Col. Ciudad Satélite C.P. 53100 Naucalpan de Juárez, Edo. de México México
  • 01-800-024-13-13

PERÚ

  • Kärcher Perú
  • Av. República de Panamá 4045 Surquillo Lima
  • Perú
  • (511) 706 – 1150

MADE IN BRAZIL / HECHO EN BRASIL KÄRCHER LTDA. VIA MIGUEL MELHADO CAMPOS, 600 VINHEDO – SAO PAULO – BRAZIL ZIP CODE 13.288-003 www.karcher.com

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals