CLASSEN SA-30 Pro Stand-Aer Stand On Aerator Owner’s Manual

June 12, 2024
CLASSEN

CLASSEN SA-30 Pro Stand-Aer Stand On Aerator

CLASSEN SA-30-Pro-Stand-Aer-Stand-On-Aerator

Product Information

  • Product Name: Stand On Aerator
  • Models: SA-30 (Starting S/N 0000 thru 0299)
  • Manufacturer: Schiller Grounds Care, Inc.
  • Website: www.classenturf.com

California Proposition 65 Warning:

  • Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.
  • Battery posts, terminals, wiring insulation, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

Product Usage Instructions

Thank you for purchasing the Classen Stand On Aerator. To ensure the best performance and longevity of the product, please follow these usage instructions:

  1. Read the Parts and Operator’s Manuals provided with the product carefully. The proper usage and maintenance of the Stand On Aerator are explained in detail.
  2. Adjust the product as instructed in the manual. Proper adjustment is crucial for optimal performance.
  3. For any service or parts needed, contact a Classen dealer. Classen service ensures that you receive the best results possible from Classen products. Classen replacement parts are manufactured with high precision and quality.
  4. Use the Stand On Aerator only as directed in the manual. Deviating from the instructions may result in reduced performance or damage to the product.
  5. Keep the Stand On Aerator in good repair. Regular maintenance and servicing will contribute to its longevity and reliability.
  6. Follow all safety warnings and instructions provided in the manual. Your safety and the safety of others are important.

For further assistance, please refer to the Parts and Operator’s Manuals or contact a Classen dealer.

STAND ON AERATOR
MODELS:
PRO Stand-Aer®
SA-30
Starting S/N 0000 thru 0299

MAN 4173455
Rev. B
PARTS MANUAL

OPERATOR’S MANUAL 4173454

www.classenturf.com

CALIFORNIA Proposition 65 Warning
Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.
Californie Proposition 65 Avertissement
Les échappements des moteurs diesel et certains de leurs composés sont reconnus par l’Etat de Californie pour être cancérigènes, provoquer des défauts congénitaux et d’autres dangers en matière de reproduction.

WARNING
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
AVERTISSEMENT
L’émission du moteur de ce matériel contient des produits chimiques que l’Etat de Californie considère être cancérigènes, provoquer des défauts congénitaux et d’autres dangers en matière de reproduction.

California Advertencia de la Proposicion 65
El estado de California hace saber que los gases de escape de los motores diesel y algunos de sus componentes producen cáncer, defectos de nacimiento y otros daños en el proceso de reproducción humana.

ADVERTENCIA
El estado de California hace saber que los gases de escape de este producto contienen productos quÍmicos que producen cáncer, defectos de nacimiento y otros daños en el proceso de reproducción humana.

CALIFORNIA
Proposition 65 Warning
Battery posts, terminals, wiring insulation, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

SA-30

IMPORTANT MESSAGE
Thank you for purchasing this Classen product. You have purchased a world class product, one of the best designed and built anywhere.
This product comes with Parts and Operator’s Manuals. The useful life and good service you receive from this product depends to a large extent on how well you read and understand this manual. Treat this product properly and adjust it as instructed, and it will give you many years of reliable service.
See a Classen dealer for any service or parts needed. Classen service ensures that you continue to receive the best results possible from Classen products. You can trust Classen replacement parts because they are manufactured with the same high precision and quality as the original parts.
Classen designs and builds its equipment to serve many years in a safe and productive manner. For longest life, use this product only as directed in the manual, keep it in good repair and follow safety warnings and instructions. You’ll always be glad you did. .
CLASSEN®
SCHILLER GROUNDS CARE, INC. 1028 STREET ROAD, P.O. BOX 38
SOUTHAMPTON, PA 18966
PHONE 877-596-6337 · FAX 215-357-8045

SAFETY

SA-30

NOTICE !!!
Unauthorized modifications may present extreme safety hazards to operators and bystanders and could also result in product damage.
Schiller Grounds Care, Inc. strongly warns against, rejects and disclaims any modifications, add-on accessories or product alterations that are not designed, developed, tested and approved by Schiller Grounds Care, Inc.Engineering Department. Any Schiller Grounds Care, Inc.product that is altered, modified or changed in any manner not specifically authorized after original manufacture-including the addition of “after-market” accessories or component parts not specifically approved by Schiller Grounds Care, Inc.-will result in the Schiller Grounds Care, Inc.Warranty being voided.
Any and all liability for personal injury and/or property damage caused by any unauthorized modifications, add-on accessories or products not approved by Schiller Grounds Care, Inc.will be considered the responsibility of the individual(s) or company designing and/or making such changes. Schiller Grounds Care, Inc.will vigorously pursue full indemnification and costs from any party responsible for such unauthorized post-manufacture modifications and/or accessories should personal injury and/or property damage result.

This symbol means:
ATTENTION! BECOME ALERT!
Your safety and the safety of others is involved.
Signal word definitions:
The signal words below are used to identify levels of hazard seriousness. These words appear in this manual and on the safety labels attached to Schiller Grounds Care, Inc.machines. For your safety and the safety of others, read and follow the information given with these signal words and/or the symbol shown above.
DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices or property damage.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, MAY result in property damage

MODEL NUMBER: This number appears on sales literature, technical manuals and price lists.
SERIAL NUMBER: This number appears only on your unit. It contains the model number followed consecutively by the serial number. Use this number when ordering parts or seeking warranty information. Located behind rider pad on frame of unit.

2

SA-30

SAFETY

MAINTENANCE SAFETY

IN GENERAL
­ Maintain machine according to manufacturer’s schedule and instructions for maximum safety and best results.
­ Park machine on level ground.
­ Never allow untrained personnel to service machine.
­ Adjust or repair only after the engine has been stopped and the tines have stopped rotating.
­ Guards should only be removed by a qualified technician for maintenance or service. Replace when work is complete.
­ Replace parts if worn, damaged or faulty. For best results, always replace with parts recommended by the manufacturer.
­ Disconnect battery or remove spark plug wire(s) before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last.
­ Do not dismantle the machine without releasing or restraining forces which may cause parts to move suddenly.
­ Provide adequate support for lifted machine or parts if working beneath.
­ Do not put hands or feet near or under rotating parts.
­ Clean up oil or fuel spillage thoroughly.
­ Replace faulty mufflers. ­ To reduce fire hazards, keep the engine, muffler,
battery compartment and fuel storage area free of grass, leaves, debris buildup or grease.

FUEL
­ Gasoline and diesel fuels are flammable; gasoline vapors are explosive. Use extra care when handling.

WARNING

­ Store only in containers specifically designed for fuel.

­ When refueling or checking fuel level:
– Stop the engine and allow to cool; – Do not smoke; – Refuel outdoors only; – Use a funnel; – Do not overfill; – If fuel is spilled, do not attempt to start the
engine until the spill is cleaned up and vapors
have cleared.

Sparks from static electricity can start fires or cause explosions. Flowing fuel can generate static
electricity. To prevent static electricity sparks:

– Keep fuel containers electrically grounded.

­ Do not fill containers in a vehicle or on a truck or trailer bed with a plastic liner. Fill containers on
the ground away from the vehicle.

­ When practical, remove gas powered equipment from the truck or trailer and refuel it on the ground. If equipment must be refueled on the truck or trailer, refuel from a portable container rather than a dispenser nozzle.

­ Keep the dispenser nozzle in contact with the rim of the fuel tank or container opening until fueling is complete. Do not use a nozzle lock-open device

­ Replace caps on fuel cans and tanks securely.

Tines
­ Tines are sharp and can cut. Use extra caution when handling. Wear appropriate personal protective equipment.

WARNING

3

SAFETY

SA-30

BATTERY Battery acid is caustic and fumes are explosive and can cause serious injury or death.

WARNING

To reduce the risk of personal injury when working near a battery:

­ Use protective equipment such as, but not limited to, goggles, face shield, rubber gloves and apron when working with battery acid.

­ Avoid leaning over a battery.

­ Do not expose a battery to open flames or sparks.

­ Be sure batteries with filler caps are properly filled with fluid.

­ Do not allow battery acid to contact eyes or skin. Flush any contacted area with water immediately and get medical help.

­ Charge batteries in an open, well ventilated area, away from sparks and flames. Unplug charger before connecting or disconnecting from battery.

­ Your unit is factory equipped with an AGM type battery . An AGM type battery charger should be used on these when charging.

STORAGE SAFETY
­ Stop the engine and allow to cool before storing.

­ Drain the fuel tank outdoors only.

­ Store fuel in an approved container in a cool, dry place.

­ Keep the machine and fuel containers in a locked storage place to prevent tampering and to keep children from playing with them.

­ Do not store the machine or fuel container near heating appliances with an open flame such as a water heater or an appliance with a pilot light.

­ Keep gasoline storage area free of grass, leaves and excessive grease to reduce fire hazard.

­ Clean grass and debris from aerating units, drives, mufflers and engine to help prevent fires.

JUMP STARTING 1. Be sure the jumper cables are in good condition.
Turn off the ignition and all electrical accessories on both machines.
2. Position the machine with a good (charged) battery next to but not touching the machine with the dead battery so jumper cables will reach.
3. When making cable connections:
– make sure the clamps do not touch anywhere except to intended metal parts,
– Never connect a positive (“+” or red) terminal to a negative (“­” or black) terminal.
– Make sure the cables won’t get caught in any parts after the engines are started.
4. Connect one end of the first jumper cable to the positive terminal on one battery. Connect the other end to the positive terminal on the other battery.
5. Connect one end of the other cable to the negative terminal of the machine with a good (charged) battery. Make the final connection on the engine of the machine to be started, away from the battery.
6. Start the vehicle with the good battery, then the machine with the discharged battery.
7. Remove the cables in the exact reverse order of installation. When removing each clamp, take care it does not touch any other metal parts while the other end remains attached.

4

SA-30 SPECIFICATIONS/ MAINTENANCE CHART

ASSEMBLY / SET UP INSTRUCTIONS

1. READ THE OPERATOR’S MANUAL BEFORE ASSEMBLY. 2. Remove the brackets securing the machine to the pallet. Reinstall the caster axle nuts. Tighten the nuts.
Fill tires at pressure at 15 psi on the rear tires and 25 psi on the front tires. 3. Lower the operator platform. 4. Open the rear panel and connect the ground wire to the battery. 5. Check the oil level in both the engine and the hydraulic tank, top off if necessary.
Use 10w30 oil for the engine. Use 15w50 or 20w50 motor oil for the hydraulic tank. 6. Fill the fuel tank with fresh clean regular grade gasoline. Open the fuel valve. 7. Start the machine and drive it off the pallet.

MAINTENANCE OPERATION

Maintenance is an ongoing job. These intervals are maximum times between maintenance operations. Perform more often under severe conditions.

FIRST 5 HOURS

BEFORE EACH USE

EVERY 25
HOURS

EVERY 40
HOURS

EVERY 100
HOURS

EVERY 200
HOURS

YEARLY

ENGINE
Consult the engine manual for additional information and instructions

Check/Top Up Oil Level

X

Check For Leaks

X

Clean Air Intake Screen
Clean Air Cleaner Precleaner
Clean Air Cleaner Element

X X X

Clean Cooling Fins

X

Change Oil And

Filter

X

Check/Replace Spark Plugs

See engine manufacturer’s manual X
TRANSAXLE*

Check Oil Level

X

X

Check For Leaks

X

X

Change Oil And

Filter

X

MACHINE

Check Interlock Operation

X

Check Tire Pressures

X

Check/Top Up Battery

X

Lubricate chains

X

Check chain tension

X

Lubricate All Points

X

*CHANGE TRANSAXLE OIL AFTER INITAL 75-100 HOURS.

5

MAINTENANCE

SA-30

CHECK DAILY
Operator Presence Interlock System – Start Operation For the engine to crank, the parking brake must be ON, and the operator present control lever must be released in the neutral position. Stand on the operator platform and check, one by one, if the engine will crank with the parking brake OFF or the operator control lever held down.
Operator Presence Interlock System – Run Operation In order for the engine to run, the operator must either be standing on the platform, or walking behind the unit with the platform up, the parking brake in the OFF position and the LH control handle held down out of the neutral position. The engine may also run if the parking brake is in the ON position, the LH control handle is rotated up into the NEUTRAL position. To check: 1. Start the engine and run at 1/2 throttle. 2. With the LH control handle in the NEUTRAL position rotated up, move the parking brake lever to ON
move the LH control lever down. The engine should kill.
Repair machine before using if the Operator Presence Interlock System does not operate correctly in start or run. Contact your authorized dealer.
Hardware Tighten any nuts and bolts found loose. Replace any broken or missing cotter pins. Repair any other problems before operating.
Tire pressure Rear Tires should be kept inflated at 15 lbs/in2 (1.05kg/cm2). Improper tire inflation can cause rapid tire wear and poor traction. Uneven inflation can cause uneven aerating. Front tires should be 25 lbs/in2 . (1.75 kg/cm²).
Engine Maintenance -Air Filter: Maintain the air filter according to the manufacturer’s engine owners manual. -Engine Oil: Check engine oil level daily. Top off if necessary. See engine owners manual.

BATTERY-AGM TYPE BATTERY SUPPLIED

Battery acid is caustic and fumes are explosive and can cause serious injury or death. Use insulated tools, wear protective glasses or goggles and protective clothing when working with batteries. Read and obey the battery manufacturer’s instructions.
Be certain the ignition switch is OFF and the key has been removed before servicing the battery.
1. Verify battery polarity before connecting or disconnecting the battery cables.
2. When installing the battery, always assemble the RED, positive (+) cable first. and the ground, BLACK, negative (-) cable last.

3. When removing the battery, always remove the ground, BLACK, negative (-) cable first and the RED, positive (+) cable last.
4. AGM type battery. Use AGM charger when charging. P/N 4171973
5. Clean the cable ends and battery posts with steel wool. Use a solution of baking soda and water to clean the battery. Do not allow the solution to enter into the battery cells.
6. Tighten cables securely to battery terminals and apply a light coat of silicone dielectric grease to the terminals and cable ends to prevent corrosion. Keep terminal covers in place.

6

SA-30
TRANSAXLE & HYDRAULIC OIL
Do not perform engine maintenance without the engine off and spark plug wires disconnected.
– Check cold. – Add 20w50 oil if necessary to the indicated level. – Do not overfill. When the oil warms up it ex-
pands. If overfilled cold, the oil may overflow at operating temperature.
Change the transaxle oil after the first 75-100 hours, then every 500 hours or yearly. It is essential that the exterior of the transaxle be free of debris, prior to fluid maintenance. 1. Raise the machine on the built in jack stands.
See jackstands section pg. 19. Put an oil drain pan under the hydraulic oil filter located under the center of the machine. Remove the filter A. This will drain the oil from the reservoir. Remove the hose from the filter to each transaxle. Remove the filter adaptor C from each transaxle to drain the transaxles. With another drain pan, drain the remaining oil from the reservoir through the drain D on the lower left side of the reservoir. Dispose of the used oil and filter properly. 2. Apply pipe compound to the reservoir drain plug and reinstall in the reservoir. Check the O-ring seal on the filter adaptor. Replace the O-ring if there are any nicks or cuts. Wipe the mounting surface on each transaxle. Reinstall the filter adaptors to the transaxles. Tighten until the adaptor body contacts the transaxle mounting surface. Wipe the filter head mounting surface. Oil the gasket of a new hydraulic oil filter and install on the filter head. Tighten 3-4 to 1 turn past the point where the gasket contacts the filter head.
3. Fill the reservoir with 20w50 (15w50 is acceptable) motor oil to the top. (Approximately 4 qts.).
4. Have more oil ready. Start the machine and watch the oil level in the sight tube on the reservoir. Add oil as the level drops below the “FULL COLD” mark. Run the machine until the oil level stabilizes.
5. Purge the transaxles, following the purging procedures. See Purging Transaxles Page 24.

MAINTENANCE

SA-30

ENGINE OIL
Do not perform engine maintenance without the engine off and spark plug wires disconnected.
AFTER FIRST FIVE (5) HOURS While the engine is warm: 1. Release the oil drain hose assembly from the
engine clip J. Lay hose assembly over the frame edge.
2. Remove the rubber cap D from the tip of the hose assembly and turn the drain valve to allow oil to drain from the engine. Dispose of used oil in accordance with local requirements.
3. Clean drain valve and tighten the plastic portion of the drain valve back into the metal portion of the valve. Replace rubber cap over the tip of the valve. Replace hose assembly back into engine clip.
4. Change oil filter.
5. Fill the crankcase with fresh oil to the full mark. Do not overfill. See engine manual for oil specifications.

DAILY
1. Check oil level with the dipstick. 2. If oil is needed, add fresh oil of proper
viscosity and grade. See engine manual for oil specifications. Do not overfill. 3. Replace dipstick before starting engine.

PERIODIC OIL CHANGES
1. See engine manual for oil and filter change intervals after the break-in period.
2. Follow instructions for first oil change, above.

SPARK PLUGS
Remove each plug and check condition. ­ Good operating conditions are indicated if the plug has a light coating of grey or tan deposit. ­ A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both
may be caused by a clogged air cleaner or improper carburetor adjustment. ­ Do not sandblast, wire brush or otherwise attempt to repair a plug in poor condition. Best results are
obtained with a new plug. ­ Set plug gap as specified in engine manual.
FUEL FILTER
An in line fuel filter is located in the fuel supply line. Inspect at every oil change to make sure it is clean and unobstructed. Replace if dirty.
8

SA-30

MAINTENANCE

PURGING TRANSAXLES
Due to the effects air has on efficiency in hydrostatic drive applications, it is critical that it be purged from the system.
These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional fluid has been added to the system.
Purging may be required if the unit shows any of the following symptoms:
– Noisy operation. – Lack of power or drive after short term use. – High operation temperature, excessive oil
expansion.
1. Check the transaxle fluid, fill to proper level, if required.

2. Raise the drive wheels off the ground. Support unit with jack stands or other suitable means.
3. With the bypass valve open, and the engine running, slowly move the control levers in both forward and reverse directions 5 to 6 times. As air is purged from the unit, the oil level will drop.
4. With the bypass valve closed, and the engine running, slowly move the control levers in both forward and reverse directions 5 to 6 times.
5. Stop engine. Check the transaxle fluid level, add fluid as required.
6. It may be necessary to repeat steps 3-5 until all the air is completely purged from the system. When the transaxle moves forward and reverse at normal speed, purging is complete.
7 .Lower the machine from the jack stands, Stop the engine and pin the jackstands in the operating position.

ENGINE COOLING
Continued operation with a clogged cooling system will cause severe overheating and can result in engine damage.
– Daily: Clean air intake screen S on air cooled engines.
– Every 100 hours: Clean cooling fins beneath blower housing H with reference to information in the engine manufacturer’s manual.

TINES
Tines can be sharp. Wear gloves when working around tines to help prevent inadvertent injuries.
Tines: ­ Replace damaged or broken tines. ­ Do not weld or straighten tines. ­ Clean tines after use, inside and out. ­ Apply a light coat of oil to tines to prevent rusting.

WARNING

9

MAINTENANCE

SA-30

SPECIFIC TORQUES

TINE BOLTS WHEEL LUG NUTS ENGINE PULLEY MOUNTING BOLT WHEEL HUB NUT

15-20 FT-LBS (20-27 Nm) 75-100 FT-LBS (102-135.5 Nm) 50-60 FT-LBS (68 Nm-81Nm) 120-140 FT-LBS (162.5-190 Nm)

CLEANING MACHINE
Clean the machine after use. Compressed air is recommended. Do not use a pressure washer. The machine will run cooler and last longer if kept free of clippings and other debris. A clean machine also reduces the risk of fire due to accumulation of combustible debris and chaff.
Brush or blow clippings and debris off the machine. DO NOT use a pressure washer.

WASHING MACHINE
CAUTION: Improperly washing a machine can cause water to enter bearings and other components. This can greatly reduce component life.
­ DO NOT use a pressure washer. Do not direct water at bearings or seals. High pressure water can blow past seals and enter sealed bearings.
­ Allow the machine to cool down before washing. Water on a warm machine can be sucked into sealed bearings as they cool.
­ Avoid getting electrical connections wet. Water can cause electrical faults and corrosion of electrical components.

10

SA-30
MAXIMUM AERATION DEPTH
Depth stops set the maximum aeration depth. Maximum aeration depth may be adjusted by changing the hole the depth stop pin is in. Typical aeration depth is 2 1/2 – 3″ (60-75 mm). Pins J1 on both sides of the machine need to be in the same hole so the tine frame is not twisted during operation. Figure 1
PARKING BRAKE CABLE
The parking brake cable is adjusted on the transaxle end of the cable. Figure 2 1. Move the parking brake lever to the “ON” posi-
tion. 2. Center the threaded conduit fitting on the mount-
ing bracket. Secure by tightening the jam nuts against the bracket. Install the bracket loosely to the frame. Pull the cable conduit until the barrel fitting just touches the bracket on the brake lever.
PARKING BRAKE SWITCH
The parking brake switch needs to be adjusted so the plunger is depressed when the parking brake is “OFF”. Figure 3 1. Move the parking brake to the “OFF” position. 2. Loosen the parking brake switch mounting
screws and move the switch until the plunger is depressed almost even with the body. Tighten the screws
FRONT CONTROL REFERENCE BAR
The front control reference bar is mounted to the control panel with slots. Moving the bar forward in the slots allows greater forward speed may be obtained. Moving it back reduces the maximum forward speed. Figure 4
Figure 4

ADJUSTMENTS
Figure 1 Figure 2
Figure 3

11

ADJUSTMENTS
TRACTION CONTROL LINKAGE
The transaxles on this machine are spring loaded to the neutral position. The traction control levers need to be adjusted so the LH lever is in the neutral slot when the tractions are released. The right hand lever is adjusted to line up with the left hand lever. To Adjust: 1. Loosen the jam nuts on either end of the con-
trol rod. Note: the end nearest the flats on the rod has left hand threads. Adjust the left rod by turning it to locate the left hand traction lever as desired. 2. Tighten the jam nuts against the rod ends to lock the adjustment. 3. Complete the adjustment by turning the right rod to line up the right traction lever with the left one.
Moving the location of the traction lever in the slot by way of adjustment can be used to affect top forward speed and reverse speed of the unit within the limits of the transaxles control stroke. Adjusting the LH control to the rear of the neutral slot will increase forward speed by reducing the available stroke for reverse and lowering maximum reverse speed. Do not adjust beyond the point where the end of the hydrostat stroke is reached before the control lever hits the front reference bar with the reference bar moved all the way forward.
TIRE SCRAPERS
Rear tire scrapers P are provided to prevent mud build up on the drive tires during operation in muddy conditions. The tire scrapers should be positioned so there is about 1/8″ (3mm) clearance between the wheel and the scraper. To Adjust: 1. Loosen the bolts securing the tire scrapers. 2. Position the tire scraper 1/8″ (3mm) from the
nearest tire surface. 3. Tighten bolts.
12

SA-30

SA-30
CHAINS
Tines may drop suddenly. Support the tines when working underneath them. NOTE: It is normal for there to be some play in the chain.
WHEEL AND TINE DRIVE CHAIN ADJUSTMENTS 1. Raise the machine and support it on the built in
jack stands. See jack stands section page 19. Turn off the engine. This will allow one of the sprockets to turn freely so the idler can take up the slack. 2. Remove the side chain covers. 3. Tension by loosening the idler bolts and sliding the idler in the adjusting slot to remove slack from the drive. Tighten the idler bolts. Replace chain covers. NOTE: If there is no more adjustment, the chain needs to be replaced. See Belt / Chain Replacement Section 4. Start the engine and lower the machine. Stop the engine and pin the jack stands in the operating position.
MAIN DRIVE CHAIN ADJUSTMENT
The main drive chain has an automatic tensioning system that normally does not require adjustment. As the chain wears, the tensioner advances and locks the idler in the new position. If the automatic tension has advanced all the way, it may be reset.
1. Raise the machine and support it on the built in jack stands. Turn off the engine.
2. Remove the front and side chain covers. Push down on the spring end of the tensioner to disengage the locking teeth. Pull the tensioner forward and lock it in place by setting the bolt in the locking notch.
3. Rotate the tire to get all the slack out of the top span of the chain.
4. Loosen the idler bolts and move the idler in the adjusting slot to remove the slack in the chain. Tighten the idler bolts.
5. Move the tensioner off the locking notch to engage the locking teeth.
6. Reinstall the chain covers. Start the engine and lower the machine. Stop the engine and pin the jack stands in the operating position.

ADJUSTMENTS
13

BELT REPLACEMENT
NOTE: Use replacement belts from Schiller Grounds care, Inc. not general purpose belts. Schiller Grounds Care, Inc. belts are specifically designed for the loads of this machine and will normally provide longer service life.
ENGINE-TRANSAXLE BELT
1. Remove the front cover. (The two knobs which secure it are located on the underside of the machine.)
2. Rotate the engine-transaxle idler arm in a counter-clockwise direction with a 3/8″ ratchet handle to allow removal of the belt. Remove the belt from the idler pulley and then from the remaining pulleys.
3. Loop a new belt around the transaxle and engine pulleys. Rotate the idler arm in a counterclockwise direction to enable the new belt to be installed in the idler pulley.
4. Reinstall the engine-transaxle belt. 5. Reinstall the front cover.
ENGINE-HYDRAULIC PUMP BELT
1. Remove the front cover. (The two knobs which secure it are located on the underside of the machine.)
2. Remove the engine-transaxle belt. 3. Rotate the engine -hydraulic pump idler in a
clockwise direction to allow removal of the belt. 4. Loop a new belt around the pump and engine
pulleys. Rotate the engine-hydraulic pump idler in a clockwise direction to enable the new belt to be installed in the idler pulley. 5. Reinstall the engine-transaxle belt. 6. Reinstall the front cover.

SA-30

14

SA-30

CHAIN REPLACEMENT

NOTE: It is recommended replacement chains from Schiller Grounds care, Inc. be used. Schiller Grounds Care, Inc. supplies a premium quality chain cut to the correct length. Replace all chains together for best results under normal circumstances.
Tension on new chains will need to be adjusted after the first several hours of operation after the chains run in. See Chain Adjustment Section.
MAIN DRIVE CHAIN
1. Start the engine and raise the machine on the jack stands. See jack stands section page 19. Stop the engine. Open the transaxle by pass valves so you can rotate the tines and axles manually.
2. Remove the front, side and tine chain covers.
3. Push down on the spring end of the tensioner to disengage the locking teeth. Pull the tensioner forward and lock it in place by setting the bolt in the locking notch.
NOTE: If replacing all chains, leave main chain broken and lying in place while the wheel and tine chains are replaced. It is easier to replace those chains with the main chain broken because the wheel and tine sprockets turn freely with the main chain disconnected.
4. Break the chain by removing the connector link. Inspect the sprockets. If any sprockets are worn, remove the chain and replace sprockets before installing the new chain. If the sprockets are still in good condition, connect the new chain to the old chain and use the old chain to pull the new chain around the sprockets. Remove the old chain and connect the ends of the new chain with a new connector link. NOTE: Install all connector links so the closed end is in the direction of forward travel.
5. Push the idler up to take all the slack out of the new chain and tighten the idler bolt. Make sure the slack is out of the top span of the chain. Move the tensioner off the locking notch to engage the locking teeth.
6. Reinstall the chain covers. Start the engine and lower the machine. Stop the engine and pin the jack stands in the operating position.

TINE CHAIN
Tines may drop suddenly. Support tines when working underneath them. 1. Start the engine and raise the machine on
the jack stands. Stop the engine. Open the transaxle by pass valves so you can rotate the tines and axles manually. 2. Remove the front, side and tine chain covers. 3. Break the main chain and leave it lying on the machine. Figure 1 4. Loosen the idler mounting bolt and back off the idler. 5. Break the chain by removing the connector link. Inspect the sprockets. If any sprockets are worn, remove the chain and replace sprockets. If the sprockets are still in good condition, connect the new chain to the old chain and use the old chain to pull the new chain around the sprockets. Remove the old chain and connect the ends of the new chain with a new connector link. NOTE: Install all connector links so the closed end is in the direction of forward travel. 6. Take the slack out of the chain by moving the idler in the adjusting slots. Tighten the idler mounting bolt. Reinstall main chain. 7. Reinstall the chain covers. Start the engine and lower the machine. Stop the engine and pin the jack stands in the operating position.
FIGURE 1

15

CHAIN REPLACEMENT

SA-30

WHEEL CHAIN
1. Start the engine and raise the machine ion the jack stands. See jack stands section page 19. Stop the engine. Open the transaxle by pass valves so you can rotate the tines and axles manually.
2. Remove the front, side and tine chain covers.
3. Break the main chain and leave it lying on the machine. Figure 1 Loosen the idler bolt and back the idler off.
4. Remove the wheel.
5. Remove the axle assembly from the machine. take the wheel chain off the axle sprocket. Figure 2
6. Break the chain by removing the connector link. Inspect the sprockets. If any sprockets are worn, remove the chain and replace sprockets. If the sprockets are still in good condition, connect the new chain to the old chain and use the old chain to pull the new chain around the sprockets. Remove the old chain and connect the ends of the new chain with a new connector link. NOTE: Install all connector links so the closed end is in the direction of forward travel.
7. Set the axle sprocket inside the chain loop and reinstall the axle assembly to the frame. Install the wheel assembly.
8. Take the slack out of the chain by moving the idler in the adjusting slots. Tighten the idler mounting bolt. Reinstall main chain.
6. Reinstall the chain covers. Start the engine and lower the machine. Stop the engine and pin the jack stands in the operating position.

FIGURE 1 FIGURE 2

16

SA-30

SPECIFICATIONS

SPECIFICATIONS

ENGINES:
Construction: Aluminum block with cast-in cast iron sleeves. Aluminum head. Configuration: 4-stroke, vertical shaft, V-twin cylinder, overhead valve, air- cooled.
DRIVE SYSTEM:
Transaxles: Dual HydroGear ZT3200 Commercial Duty Hydrostatic transaxles (10cc Pumps) Turn Radius: True Zero
CONTROLS:
Throttle, choke, PTO switch, key switch, operator present, traction levers (1 per wheel), parking brake, tine raise/lower, tine down pressure.
GROUND SPEED:
Forward 0-7.4 mph (0-11.9 kph) Reverse 0-3.5 mph (0-5.6 kph)
BRAKES:
Hydrostat provides dynamic braking Parking brake: Mechanical paul type in transaxle

DRIVE TIRES:
18 X 6.50-8 Pressure: 15 p.s.i. (1.05 kg/cm²)
CASTERS:
13 X 5.00-6 Pressure: 25 p.s.i. (1.75 kg/cm²)
AERATION:
TINES: 3/4″ (19mm) formed from .08 in hardened chrome molybdenum alloy steel. 48 per unit.
PENETRATION DEPTH: 2-5″ (50-250 mm) maximum Adjustable depth set for consistent depth.
AERATION WIDTH: 30″ (762mm)
HOLE PATTERN: 3-3/4″ X 7″ (95mm X 178mm) on center
PRODUCTION: Up to 92,400 sq. ft./hour

TRANSMISSION DRIVE SYSTEM:
Belt from engine to hydrostat input shafts, hydrostatic drive to wheels and tines via #50 chain.

TURNING RADIUS:
True zero tines up. Approximately 48″ radius tines down.

HYDRAULIC RESERVOIR CAPACITY:
Reservoir 2.75 quarts Transaxles 2 quarts Total Capacity 6.75 quarts

POWER STEERING:
Independently controlled drive wheels.

WEIGHT:
554930….Dry : Approximately 1210 lbs.
Wet: Approximately 1245 lbs.

17

SPECIFICATIONS

SA-30

ENGINE

MODEL NUMBER

SA-30

MANUFACTURER KAWASAKI

MODEL

FS541V

CYLINDERS

2

COOLING

Air

FUEL

Gasoline

BORE/STROKE

2.9″ x 2.8″ (73 x 72 mm)

DISPLACEMENT

36.8 ci (603 cc)

COMPRESSION

8.1:1

OUTPUT POWER

Refer to engine manufacturer’s specifications and website

OUTPUT TORQUE

31.0 ft-lb (42.1 Nm) @2200 rpm

OIL CAPACITY

1.8 qt (1.7L)

LUBRICATION

Full Pressure

CYLINDER BLOCK

Aluminum with cast iron sleeve

CYLINDER HEAD

Aluminum

GOVERNOR

Mechanincal

AIR CLEANER

Dual Element

IGNITION SYSTEM CHARGING SYSTEM BATTERY FUEL CAPACITY FUEL TANK FUEL CONSUMPTION @ MAX LOAD/ SPEED

Electronic 12V-15AMP 12V 5.0 GAL (18.9 L) Polyethylene 1.35 gal/hr (5.11 L/hr)

18

SA-30

PARTS SECTION

PARTS SECTION

19

UPPER ENGINE ASSEMBLY
FIGURE 1

SA-30

27

21

19 16
18
17 15
16

12 25

7 27
10
27 14

28 26
6 25
5
22 23
24

20 8 4
4

13
11 25 29

8

26 6

9

1

3

2

20

SA-30

UPPER ENGINE ASSEMBLY
FIGURE 1

ITEM PART NO. DESCRIPTION

QTY

1 4173494

S-MAIN FRAME

1

2 64018-7

BLT-CRG 3/8-16X1-1/4

2

3 64018-44

BLT-CRG 3/8-16X1 SN

6

4 64001-6

NUT-HEX JAM 3/8-16

8

5 4171512.7 PLT-ENGINE MOUNTING

1

6 64263-007 BLT-FLG HD M8-1.25 X 20

4

7 64262-002 BLT-FLG HD 1/4-20 X 3/4

4

8 64268-03

NUT-FL NYLON LOCK 3/8-16 8

9 4172292.7 GUARD-MUFFLER

1

10 4172912.7 LABEL-HYDRA-COOL

1

11 64229-01

NUT-NYLON LOCK 1/4-20

4

12 4172735.7 BRKT-OIL COOLER

1

13 2188173

COOLER-OIL

1

14 2720891.7 SCREEN-OIL COOLER

1

15 4164252-001 FITTING-3/8NPT TO 3/8 BARB 1

16 88042-03

CLAMP, HOSE 5/8

2

17 69053-13

HOSE, HYDRAULIC 14″

1

18 48412-01

CLIP-CABLE 3/4 J X 10.32

1

19 4164251

DRAIN VALVE

1

20 4164359

MUFFLER-FS600 KAW

1

21 4164382

ENG-18HP KAW FS541V ES 1

22 64163-69

WSHR .391X.88X10 GA

2

23 64006-03

LOCKWSHR-3/8 HELICAL

2

24 64123-87

BLT-HEX 3/8-16 X 1-3/4

2

25 64268-02

NUT-FL NYLON LOCK 5/16-18 4

26 64163-02

WSHR .321X.593X11GA

4

27 64018-51

BLT-CRG 5/16-18 X 3/4 SN

4

28 4172746.7 BRKT-COOLER, SPRT RH

1

29 4172876.7 BRKT-COOLER, SPRT LH

1

ITEM

PART NO.

DESCRIPTION

QTY

  • NOT ILLUSTRATED
    21

LOWER ENGINE ASSEMBLY
FIGURE 2
36

SA-30
4

5
2 9

39 1

6

35 31

37

3

11 32

10

22

7

12

30

40 23

25 28

27

34

13

14

26 29 16 34 23
18
19 24
28
8 33
38

21 20 17
15 18 19 23

22

SA-30

LOWER ENGINE ASSEMBLY
FIGURE 2

ITEM PART NO. DESCRIPTION

QTY

1 4171512.7 PLT-ENGINE MOUNTING

1

2 4173822

PUMP-GEAR 2.1XCC

1

3 4171447

PULLEY-4 IN

1

4 4164382

ENGINE-KAW FS541V ES

1

5 2690030-03 FTG-3/4-16 ORB X 1/2 BARB 1

6 4173494

S-MAIN FRAME

1

7 64006-06

LOCKWSHR-7/16 HELICAL

1

8 2308000

PULLEY-IDLER 4.00 EOD

1

9 25-2503-8-6 FITTING 90 -8 MORB X -6 MJIC 1

10 64163-51

WSHR.453X1.38X7GA

1

11 64164-38

KEY 1/4 X 3-1/2 SQ

1

12 64123-155 BLT-HEX 7/16-20X3

1

13 4172467

SPACER-IDLER ARM

1

14 4116661

PIN-PIVOT

1

15 4171402

S-IDLER ARM, TRANS

1

(INCLUDES ITEMS 17-21)

ITEM

PART NO.

16 4171398

S-IDLER ARM, PUMP

1

(INCLUDES 18, 19, 29)

17 85010N 18 4128004 19 64144-40 20 548138 21 521438 22 64123-87 23 64229-03 24 33148-01 25 4171403 26 4171399 27 64123-217 28 64006-03 29 4127999 30 48393 31 4171469 32 4171450 33 64123-75 34 4163586 35 64262-007 36 64141-6 37 64044-1 38 64123-67 39 64018-30 40 64163-69

ZERK 1/4-28 STR SELF THRD 1

BEARING-BALL 10 X 26 X 8

3

SNAP RING-26MM INTERNAL 2

BRG NDL.88 1.12 1.00

1

GREASE SEAL

1

BLT-HEX 3/8-16 X 1-3/4

1

NUT-NYLON LOCK 3/8-16

3

SPACER-0.379X0.750X0.25

1

PIN – SPRING

1

PIN – MNTING, PUMP IDLER

1

BLT-HEX 3/8-16X4-1/4

1

LOCKWSHR-3/8 HELICAL

2

SEAL-16 X 24 X 7

1

PULLEY-V IDLER

1

BELT-HA 30 ED

1

PULLEY-4 IN ‘A’

1

BLT-HEX 3/8-16 X 3

1

SPRING-EXTENSION

2

BLT-FLG HD 5/16-18 X 1

4

NUT-WLF 5/16-18

4

SCREW-SET 1/4-20X1/4

2

BLT-HEX 3/8-16 X 2

1

BLT-CRG 3/8-16 X 4-1/2

1

WSHR .391X.88X10 GA

1

DESCRIPTION

QTY

*NOT ILLUSTRATED
23

FUEL TANK, BATTERY, RESERVOIR
FIGURE 3

SA-30

39 30
20
22 17
21 30

19

30 26

30

16
41 14

94 3

8
(10″)

9

13

10 13

26

11

(36″)

8
(7″)

15 23

31

18

31

12
8
(12″)
40

24 29

36 32 31 27

25

27

38

31

35

30 37

34 33

7 5
2
6
9

1

28
24

SA-30

FUEL TANK, BATTERY, RESERVOIR
FIGURE 3

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO. DESCRIPTION

QTY

1 4173494

S-MAIN FRAME

2

2 4165561-1 TANK-FUEL, MIDSIZE

1

(INCLUDES ITEMS 5-7)

3 4165387

GROMMET, ROLL-OVER

1

4 4165763

TANK VENT

1

5 4132325

GROMMET-SEALING

1

6 4165561-2 TUBE-FUEL, PICK-UP

1

7 4167989

CAP-FUEL, 3.5IN EPA

1

8 4162977-001 HOSE-FUEL 1/4 INCH

3

9 88042N

CLAMP-HOSE

6

10 4165864

FITTING, 1/4 TO 3/16

1

11 4162989

HOSE-FUEL 3/16 INCH

1

12 4163016

VALVE- IN-LINE FUEL

1

13 88042-01 CLAMP-HOSE 3/16

2

14 4173495

S-RESERVOIR

1

(INCLUDES ITEMS 15,16, & 23)

15 108029

PLUG MAGNETIC

1

16 4171557-3 CAP-1″ NPT W/VENT HOLES 1

17 4173496

S-PLATE BATTERY, CLAMP

1

18 2183071-04 SPACER

4

19 4171099

BATTERY-190CCA

1

20 2228065

DAMPER-NON-CAVITATING

2

21 2000590

LABEL-WARN BATTERY

1

22 4171533.7 PLT-BATTERY HOLDER

1

23 4172910

LABEL-RESERVOIR

1

24 4171281

CYLINDER-2.25 X 3.0

1

25 4171592

PIN-CYLINDER

1

26 64018-51 BLT-CRG 5/16-18 X 3/4 SN

6

27 64268-03

NUT-FL NYLON LOCK 3/8-16

8

28 64018-44 BLT-CRG 3/8-16X1 SN

4

29 85010N

ZERK 1/4-28 STR STH

1

30 64268-02 NUT-FL NYLON LOCK 5/16-18 10

31 548602

PIN-HAIR

4

32 548603

PIN-CLEVIS

1

33 38665

SOLENOID

1

34 64152-23 SCREW-SP 1/4-20X3/8

2

35 64123-15 BLT-HEX 3/8-16X3/4

4

36 64006-03 LOCKWSHR-3/8 HELICAL

4

37 64163-31 WSHR 25/64X1X12

4

38 64001-6

NUT-HEX JAM 3/8-16

4

39 64262-025 BLT-FLG HD 3/8-16 X 2-1/2 LG 4

40 4172659.7 WLDMT-BATTERY SUPPORT 1

41 4171586

BUMPER-RUBBER

1

*NOT ILLUSTRATED

25

WHEEL ASSEMBLIES
FIGURE 4

SA-30

24 23
2 27

25
22 26

4 3

11

21

9

14

10 18

20 16

19

13

15

27 29 28
17

5

1

31
26 12
6 7 8

26

SA-30

WHEEL ASSEMBLIES
FIGURE 4

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO. DESCRIPTION

QTY

1 4172857

ASSY-WHEEL 13X5.00-6

2

2 64018-7

BLT-CRG 3/8-16X1-1/4

8

3 64187-03

NUT-WHEEL 1/2-20

8

4 4171862

ASSY-WHEEL 18X6.50-8

2

5 64123-215

BLT-HEX 3/4-10X7-1/2

2

6 64229-07

NUT-NYLON LOCK 3/4-10

2

7 2722231

SPACER-END

4

8 2722230-02 SPANNER

2

9 4173176

WLDMT-AXLE SHAFT

2

10 64268-03

NUT-FL NYLON LOCK 3/8-16

8

11 4171458.7

WLDMT-WHEEL SPINDLE HOUS 2

12 2721306.7

CASTER YOKE

2

13 4167554-01 BEARING-SPINDLE SEALED 4

14 4172715

SPACER-SPINDLE

2

15 4171467.7

WLDMT-WHEEL HUB

2

16 85010N

ZERK 1/4-28 STR SLF THRD 2

17 48480

SEAL CR 12411

2

18 64151-28

NUT-HEX 5/8-18 CTR LOCK

2

19 64209-03

SPRING WASHER.67 ID

2

20 64164-12

KEY-1/4X1 SQ

2

21 64001-6

NUT-HEX JAM 3/8-16

8

22 64163-26

WSHR .766 ID X 1.625

2

23 64025-20

NUT-HEX 3/4-16 SLOT U

2

24 64140-9

COTTER PIN-1/4-2

2

25 4162986

CAP-END

2

26 48043-04C

CONE-OUTER BEARING

4

27 48043-03C

CUP-OUTER BEARING

4

28 4172865

LINK-CONNECTOR #50

2

29 4172864-03 CHAIN-50 ROLLER 67 PITCH 2

30* 4173503

KIT-CHAINS REPLACEMENT 1

(INCLUDES ALL 6 CHAINS FOR UNIT AND LINKS)

31 4173494

S-FRAME, MAIN

1

(INCLUDES ITEM 27)

*NOT ILLUSTRATED

27

PARKING BRAKE ASSY
FIGURE 5

SA-30
34

16

3

14 13

4 30 31

21
21 24

2 23

10 29

17 19 7 9
18 11

6

20

1

28

23

8

5

26
15 25

30

31

22

12

27

28

SA-30

PARKING BRAKE ASSY
FIGURE 5

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO. DESCRIPTION

QTY

1 4171573.7 BRKT-BRAKE MOUNT

1

2 4173512

S-BRAKE ARM BRAKT

1

(INCLUDES ITEM 10)

3 4168180

KNOB-PUSH ON

1

4 4171580

WLDMT-BRAKE HANDLE

1

5 4173527.7 BRKT-BRAKE, PARKING

1

6 4173896.7 BRKT-CABLE

1

7 4117212

SPRING-EXTENSION

2

8 4173898

CABLE-BRAKE, PARKING

1

9 4171581

HUB-BRAKE PIVOT

1

10 4166324-03 BEARING-PLASTIC 1.000 ID

1

11 2308094

SWITCH-NCNC DBL POLE

1

12 64188-02 PIN-CLEVIS 5/16 X 1

2

13 516544

BUSHING (PLATING)

2

14 41-053

SPRING COMP .681 X 1.125

1

15 64018-55 BLT-CRG 3/8-16X3-1/2

1

16 64262-018 BLT-FLG HD 3/8-16 X 1-3/4

2

17 64141-4

NUT-WLF 3/8-16

4

18 64152-46 SCREW-SLT HH 10-24X1/2

2

19 4113682

ROD-SPRING MOUNT

2

20 64018-51 BLT-CRG 5/16-18 X 3/4 SN

2

21 64229-03 NUT-NYLON LOCK 3/8-16

3

22 64163-55 WSHR .328X.75X14 GA

2

23 64168-2

COTTER-HAIRPIN .08 X 1.19

3

24 64163-87 WSHR- .391×1.375x12GA

1

25 64025-15 NUT-HEX #10-24 KEPS

2

26 64018-7

BLT-CRG 3/8-16X1-1/4

2

27 4171283

TRANSAXLE, HYDROSTATIC RH 1

28 4171282

TRANSAXLE, HYDROSTATIC LH 1

29 64268-02 NUT-FL NYLON LOCK 5/16-18 2

30 4172865

LINK-CONNECTOR #50

2

31 4172864-01 CHAIN 50 ROLLER 57 PITCH

2

32* 4173503

KIT-CHAINS REPLACEMENT

1

(INCLUDES ALL 6 CHAINS FOR UNIT AND LINKS)

*NOT ILLUSTRATED

29

ELECTRICAL SYSTEM
FIGURE 6

SA-30

10

TO STARTER
14

12
(RED)

14

CHARGE CONNECTION

TO SOLENOID (2)

ENGINE KILL

W

P

G

CARB SOLENOID

15
BATTERY

11

4

(RED)

SOLENOID

1

2

3

4

SOLENOID

STARTER SOLENOID

R YR B

14

8.0 EXP

14 GA

BB B

BATTERY
13
(BLACK)
GROUND
ENGINE BLOCK (GROUND)

9

RR PP

3

30

RB P RB

86

85

87 87A

NC

O NO

O

CHARGING RELAY

AUXILIARY POWER

OB OB

3.0 EXP

3.0 EXP

NC NC

YR

CODE B G O OB P R W WB Y YB YR

8

WIRE COLORS AND GAUGE

COLOR

GAUGE UNLESS NOTED

BLACK

16

GREEN

16

ORANGE

16

ORANGE W/BLACK STRIPE

16

PURPLE

14

RED

14

WHITE

16

WHITE W/BLACK STRIPE

16

YELLOW

16

YELLOW W/BLACK STRIPE

16

YELLOW W/RED STRIPE

16

OB O

LIFT SWITCH
2

O B

6
HOUR METER 12 34
KEY SWITCH

R B

30

MANIFOLD SOLENOID

OB B
NO NC W
W WB
Y YB

O W YW

WB GO

7
PARK BRAKE SWITCH
5
OPC SWITCH

WB

B YB

B

SA-30

ELECTRICAL SYSTEM
FIGURE 6

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO. DESCRIPTION

QTY

1 4172161 HARNESS-WIRING MAIN

1

(INCLUDES ITEM 9)

2 128010

KEY-SWITCH

1

3 2722325 RELAY-40AMP SEALED

1

4 38665

SOLENOID

1

5 108208

SWITCH-DBL POLE

1

6 4171992 METER-HOUR

1

7 2308094 SWITCH NCNC

1

8 4171893 SWITCH-ROCKER

1

9 148082-20 FUSE-20 AMP

2

10 4171099 BATTERY-AGM TYPE

1

4171973 CHARGER-AGM

11 2722227-05 CABLE-BATTERY 18″ COND 1 (INCLUDES ITEM 14 & 15)

12 108061-17 CABLE-BATTERY 16 RED

1

13 108061-16 CABLE-BATTERY 31.5 BLK 1

14 2308095 COVER – TERMINAL

3

15 112386

BOOT BAT TERM POS

1

31

TRANSAXLE ASSEMBLY
FIGURE 7

12

25

5 24

SA-30

FROM RESERVIOR

55

18 30

25

22

11

16

25

38

9

37

29

36 28

21 32

34 35 23 86 7 4

17 10

19

1

31

14

13

TO OIL COOLER
24 15
11 2
33 31
5 3
20

26 27

32

SA-30

TRANSAXLE ASSEMBLY
FIGURE 7

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO.

1 4171283 2 4171282 3 4172890.7 4 64262-011 5 64268-02 6 518438 7 4169194 8 64163-61 9 4172705 10 64229-03 11 33030-4A 12 64123-138 13 64123-104 14 64163-02 15 4172704 16 G8062 17 4172456.7 18 4172523 19 4171487.7 20 4171666.7 21 64168-2 22 4171606-1 23 64262-012 24 64141-2 25 64139-02 26 64018-15 27 64018-51 28 4172459 29 4164048 30 64187-03 31 64268-03 32 4171665.7 33 4171664.7 34 2720977 35 4148697 36 64229-01 37 2720396 38 138059

TRANSAXLE, HYDROSTATIC RH 1

TRANSAXLE, HYDROSTATIC LH 1

BRKT-SHIELD SUPPORT

1

BLT-FLG HD 3/8-16 X 1

2

NUT-FL NYLON LOCK 5/16-18 8

BUSHING

2

BUSHING – .522 X ..688 X .289 2

WSHR .81X.406X16GA

2

TUBE RESERVOIR-FILTER

1

NUT-NYLON LOCK, 3/8-16

4

IDLER BUSHING

4

BLT-HEX 3/8-16 X 3-3/4

4

BLT-HEX 5/16-18X2-3/4

4

WSHR .321/.328X.593/.608X11GA 4

TUBE-TRANS – COOLER

1

CLAMP HALF 3/8 INSULATED 3

PLATE-SPACER

2

SPROCKET – #50-28, TRANS

2

PLATE-TRANS ACTUATOR

2

PLT-DUMP VALVE

1

COTTER-HAIRPIN .08 X 1.19

2

CLAMP-HALF 1/2 HOSE

3

BLT-FLG HD 3/8-16 X 1-1/4

2

NUT-WLF 1/4-20

6

BLT-WLF 1/4-20X1/2

8

BLT-CRG 5/16-18X1 SN

1

BLT-CRG 5/16-18 X 3/4 SN

5

BELT-HA 54.80

1

KIT-TRANSAXLE, FAN & PULLEY 2

NUT-WHEEL 1/2-20

8

NUT-FL NYLON LOCK 3/8-16

4

LINK-DUMP VALVE, RH

1

LINK-DUMP VALVE, LH

1

SPRING-COMPRESSION

2

ROD-PULL FREEWHEEL

2

NUT-NYLON LOCK 1/4-20

2

FILTER-25 MICRON SMALL CAN 1

FILTER HEAD

1

DESCRIPTION

QTY

33

OIL COOLING SYSTEM
FIGURE 8

SA-30

30

4

3

29 6.5″

22

41

36 38

27

2

37

(7.75″)
33

31
(18″)

39

10 34
28

9
27
(17.5″)

27
(14″)
28
20

23
(33″)
1

22
22
23
(29″)

26 5

24 25

19

32
(17.75″)

21 6

14 28

10 33

35
(2.5′)
15

13 22

32
(6″)

34

9

28

32
(3.75″)

35
(9.625″)
22

35
(5.75″)

28

28

32
(17.75″)

28 12 40 11

17

18

8

7

40
12 28 11

34

SA-30

OIL COOLING SYSTEM
FIGURE 8

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO.

1 2188173

COOLER-OIL

1

2 4173495

S-RESERVOIR

1

3 4171280

MANIFOLD-AERATOR

1

4 4171284

GAUGE-HYDRAULIC 0-1000 PSI 1

5 4171281

CYLINDER-2.25 X 3.0

1

6 4173822

PUMP-GEAR 2.1XCC

1

7 4171282

TRANSAXLE, HYDROSTATIC LH 1

8 4171283

TRANSAXLE, HYDROSTATIC RH 1

9 2720396

FILTER-25 MICRON SMALL CAN 1

10 138059

FILTER HEAD

1

11 4172699

FTG -06 MORB X 3/8 HOSE 90 1

12 2690030-03 FTG-3/4-16 ORB X 1/2 BARB 45 2

13 4172704

TUBE-TRANS – COOLER

1

14 4172705

TUBE RESERVOIR-FILTER

1

15 4172860

FTG-3/8 Y HOSE CONNECTOR 1

16 58026-04

CONNECTOR-3 WAY, 1/2″

1

17 158058-04 FTG -06 MORB X 3/8 HOSE 90 1

18 2690030-01 FITTING-9/16-18 ORB X 3/8

1

19 4166840-03 HOSE-#6 JIC/90 JIC X 39.75

1

20 2690030-03 FTG-3/4-16 ORB X 1/2 BARB 1

21 25-2503-8-6 FITTING-90 -9 MORB X -6 MJIC 1

22 88042-04

CLAMP, HOSE

14

23 69053-13

HOSE-HYD (9″ L)

3

24 4166839-03 HOSE-#6 JIC/JIC 19.5

1

25 4166839-02 HOSE-#6 JIC/JIC 18.5

1

26 25-2503-6-6 FITTING 90 -6 MORB X -6 MJIC 2

27 138058-05 HOSE-BULK .50ID X .84 OD

2

28 88042-05

CLAMP-HOSE 13/16

12

29 4172859-03 HOSE- 3/8 ID X 5/8 OD CLEAR 1

30 4173002

VENT-BREATHER

1

31 69053-14

HOSE-HYD (9″ L)

1

32 138058-A1 HOSE-BULK.50IDX.84OD

4

33 108086-03 FTG-BARB 90-1/2 X 3/8 MNPT 1

34 4164252-002 FITTING-3/8MNPT X 1/2M BARB 1

35 69053-18

HOSE-HYDRO

3

36 25-2502-4-4 FTG 90 -4 MJIC X -4 FPT

1

37 4172326-01 HOSE-#4JIC/JIC 90 LG 17.38 1

38 69060-01

FITTING-ORB X 45 BARB

1

39 25-0503-6-6 FITTING STR -6 M ORB/-6 MJIC 3

40 158061-32 O-RING #228 BUNA

2

DESCRIPTION

QTY

*NOT ILLUSTRATED

35

CONTROL PANEL & TOWER ASSY
FIGURE 9

SA-30

19 14

14 28

4

16

3

14
7 17
20 25
23

2

1 22 11

18

11 7
24

13

10

5

21

11 24
5
8

14
29 34

11

15

22

9 27
TO RESERVOIR TANK
26
TO PUMP

12
TO CYLINDER
30

6

11
33 32 31

35 23

36

SA-30

CONTROL PANEL & TOWER ASSY
FIGURE 9

ITEM PART NO. DESCRIPTION

QTY

1 4173504

S-CONTROL PANEL

1

2 4172858

LABEL-CONTROL PANEL

1

3 4171992

HOUR METER-MAG SENSE

1

4 128010

SWITCH KEY

1

5 64141-2

NUT-WLF 1/4-20

2

6 4172326-01 HOSE-#4JIC/JIC 90 LG 17.38 1

7 4171284

GAUGE-HYDRAULIC 0-1000 PSI 1

8 118020-22 CONTROL-THROTTLE, 57.5IN 1

9 4171280

MANIFOLD-AERATOR

1

10 820529

SPACER

3

11 64268-02

NUT-FL NYLON LOCK 5/16-18 21

12 25-2502-4-4 FTG 90 -4 MJIC X -4 FPT

1

13 64268-05

NUT-FL NYLON LOCK 1/2-13 2

14 64018-51

BLT-CRG 5/16-18 X 3/4 SN

17

15 25-2503-4-4 FITTING-ORB X 45 BARB

1

16 4171511

BAR-REFERENCE REVERSE 2

17 108009-03 CONTROL-CHOKE 51

1

18 64025-04

NUT-3/8-24 HEX

1

19 4170593.7 WLDMT-FRONT POINT

1

20 64152-46

SCREW-SLT HH 10-24X1/2

2

21 64025-15

NUT-HEX #10-24 KEPS

2

22 48228-2A CLAMP-3/4 CLIP

2

23 64018-2

BLT-CRG 1/4-20X3/4

3

24 4171606-1 CLAMP-HALF, 5/8 HOSE

2

25 64262-005 BLT-FLG 1/4-20 X 1-1/2

3

26 25-0503-6-6 FITTING STR -6 M ORB/-6 MJIC 3

27 69060-01

FITTING-ORB X 45 BARB

1

28 4173505

S-PANEL,TOWER LH

1

29 4173506

S-PANEL,TOWER RH

1

30 4171495.17 PANEL-BACK

1

31 4172866

SNAP-SPRING 3/16

1

32 4171100

TETHER-WIRE, COATED

1

33 64229-01

NUT-NYLON LOCK 1/4-20

1

34 64018-15

BLT-CRG 5/16-18X1 SN

1

35 64262-006 BLT-FLG HD 5/16-18 X 3/4

2

ITEM

PART NO.

DESCRIPTION

QTY

*NOT ILLUSTRATED

37

HANDLE CONTROLS
FIGURE 10

SA-30
6 1

1

46

38

42

31

5

48 45

50

44

46

32

28

52

42

2927 47

28

21

30

26

42

49 20

23

22 35 43

25 45 41 40
28 34

20
28 39

42 22

23 35

43

37

22

33

16

23

13

19 51 10

36

20 51

3 4 53

37

6

28

23

20 51

33

51

22

9 36

13

16

8

2 12 10

11

24

7

4 53

3

15 14 17 17
18 14

7

12 11

9

6

2

38

SA-30

HANDLE CONTROLS
FIGURE 10

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO.

1 64018-44 BLT-CRG 3/8-16X1 SN

4

2 64262-012 BLT-FLG HD 3/8-16 X 1-1/4

2

3 64268-01 NUT-FL NYLON LOCK 1/4-20

2

4 64140-18 COTTER PIN-1/4-2

2

5 64262-013 BLT-FLG HD 3/8-16 X 1-1/2

2

6 64018-51 BLT-CRG 5/16-18 X 3/4 SN

6

7 64229-03 NUT-NYLON LOCK, 3/8-16

2

8 4171478.7 ARM-LINK, RH

1

9 64141-6 NUT-WLF 5/16-18

4

10 4171476.7 LINK-TRANSAXLE

2

11 518438

BUSHING

2

12 4169194 BUSHING – .522 X ..688 X .289 2

13 4171388 SHAFT-LIFT PIVOT

2

14 64163-61 WSHR .81X.406X16GA

8

15 64221-07 E-RING, 3/8″

4

16 4166324-03 BEARING-PLASTIC 1.000 ID

2

17 4171416.7 LINK-LIFT

4

18 33138-07 PIN CLEVIS GRVD .38 X 1.25

4

19 4171479.7 ARM-LINK, RH

1

20 64268-02 NUT-FL NYLON LOCK 5/16-18

4

21 64262-027 BLT-FLG HD 3/8-16 X 2-1/4 GR8 1

22 64262-008 BLT-FLG HD 5/16-18 X 1-1/4

4

23 64163-02 WSHR .328X608X11GA

4

24 4171433.7 WLDMT-LIFT PIVOT

1

25 64163-31 WSHR 25/64X1X12

1

26 64025-15 NUT-HEX #10-24 KEPS

2

27 64152-49 SCREW-SLT HH 10-24X1.25

2

28 64229-03 NUT-NYLON LOCK 3/8-16

11

29 64158-01 EYE BOLT-10-24 X 1.25 THD LG 1

30 64141-15 NUT-WLF 10-24

2

31 4171442 HANDLE-CNTRL OP PRESENCE 1

32 4171515.7 BRKT-CONTROL LEVER

1

33 64025-03 NUT-HEX 5/16-24

2

34 4171520.7 BAR-CONTROL

1

35 4143595-02 ROD END-FEMALE 5/16-24 LH 2

36 4143595-01 ROD END-FEMALE

2

37 4171475 ROD-CONTROL

2

38 4171171 HANDLE-CONTROL,STATIONARY 1

39 4171461 SPRING-EXTENSION

1

40 4171409 SPACER-.625 X.386X1.260

1

41 4166324-04 BEARING-PLASTIC .625 X1.25LG 1

42 2188145 BEARING-.75ID BRZ SELF ALIGN 4

43 64025-33 NUT-HEX 5/16-24 LH

2

44 4171893 SWITCH-MINIATURE ROCKER 1

45 85-SC12 SET COLLAR 3/4″

2

46 4172963 GRIP-CONTROL

2

47 108208

SWITCH DBL POLE

1

48 4171523.7 ARM-SWITCH

1

49 64123-50 BLT-HEX 3/8-16X1

2

50 4171573.7 BRKT-BRAKE MOUNT

1

51 4168069 BEARING-FLUSHMNT,1.0 SHAFT 4

52 64168-2 COTTER-HAIRPIN.08X1.19

1

53 64262-003 BLT-FLG HD 1/4-20 X 1

2

DESCRIPTION

QTY

39

DEPTH STOP & HOC ASSEMBLY
FIGURE 11

SA-30

7

24

8

17

9

39

14 12

38

37

7

36 10

8

38 39

13

40
18 13
5 1 3
2
15 15
32

16 6
33 31 2

23

13

22

4
19 25 21 20

26 6
26

27 30 28 11 29 35 41 34

40

SA-30

DEPTH STOP & HOC ASSEMBLY
FIGURE 11

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO. DESCRIPTION

QTY

1 4117212

SPRING-EXTENSION

2

2 4172452

PLATE-GUIDE

4

3 4172453

PLATE-LOCK

4

4 2183071-04 SPACER

4

5 4169597

EYE BOLT 5/16-18 X 1.5

2

6 83-5013E08 SPROCKET-WHEEL,FRONT 4

7 4172671

ARM-DEPTH

2

8 4172672

HUB-DEPTH ARM

2

9 4172679.7 WLDMT-DEPTH SET RH

1

10 4172677.7 WLDMT-DEPTH SET LH

1

11 4172454

ARM-IDLER LOCK

2

12 64001-6

NUT-HEX JAM 3/8-16

4

13 64141-6

NUT-WLF 5/16-18

6

14 64018-31

BLT-CRG 3/8-16 X 2-1/2

4

15 64141-4

NUT-WLF, 3/8-16

4

16 64163-74

WASHER: .516 X 2.00 X .250 2

17 64018-13

BLT-CRG 1/2-13X2 GR5

2

18 64268-05

NUT-FL NYLON LOCK 1/2-13 2

19 4168176

TUBE-PIVOT, IDLER INNER 2

20 64163-19

WSHR 33/64X1-1/4X12GA

4

21 64123-72

BLT-HEX 1/2-13X2-1/2

2

22 64141-13

NUT-WLF 1/2-13

4

23 4172457.7 WLDMT-IDLER ARM

2

24 64268-03

NUT-FL NYLON LOCK 3/8-16 4

25 4166324-03 BEARING-PLASTIC 1.000 ID 2

26 64163-36

WSHR 1X33/64X.187

4

27 64123-24

BLT-HEX 1/2-13X2

2

28 4172782

HUB-TENSIONER ARM

4

29 4172783

PLATE-SPRING GUIDE

4

30 64168-2

COTTER-HAIRPIN .08 X 1.19 2

31 64025-01

1/4-20 HEX NUT

2

32 64229-01

NUT-NYLON LOCK 1/4-20

2

33 64123-07

BLT-HEX 1/4-20X1-1/2

2

34 64262-019 BLT-FLG HD 5/16-18 X 1-3/4 2

35 4166927

SPRING COMPRESSION

2

36 64188-68

PIN-CLEVIS 3/8 X 1.25

2

37 64168-7

COTTER-HAIRPIN .091 X 1.88 2

38 64221-1

E-RING, 1″

2

39 64163-64

WSHR 1.015X1.500X14GA

2

40 64018-44

BLT-CRG 3/8-16X1 SN

4

41 4172784

PLT-SPRING STOP

2

  • NOT ILLUSTRATED

41

JACKSHAFT ASSEMBLY
FIGURE 12

SA-30

12 14

2

1

5

19

7

17 15

17 3

2 10

2 3 13 9

18 8 17 17 15

7
6 11 16

4 11

42

SA-30

JACKSHAFT ASEMBLY
FIGURE 12

ITEM PART NO. DESCRIPTION

1 64262-011 BLT-FLG HD 3/8-16 X 1

2 64141-6

NUT-WLF 5/16-18

3 64018-15 BLT-CRG 5/16-18X1 SN

4 64123-24 BLT-HEX 1/2-13X2

5 64163-19 WSHR 33/64X1-1/4X12GA

6 64141-13 NUT-WLF 1/2-13

7 4171394.7 WLDMT-TINE ASSY

8 64044-18 SCREW-SET 5/16-18 x 5/16

9 64164-40 KEY 1/4 X 1 3/4 SQ

10 64221-1

E-RING 25MM/1.00

11 64163-124 WSHR-.531 X 1.50 X .125

12 64044-13 SCREW-SET 1/4-28X1/4

13 4171346

SHAFT – HALF, TINE DRIVE

14 64164-12 KEY-1/4X1 SQ

15 64018-51 BLT-CRG 5/16-18 X 3/4 SN

16 83-5013E08 SPROCKET-WHEEL,FRONT

17 4168069

BEARING-1″ FLUSHMOUNT

(INCLUDES ITEM 12)

18 4171445 19 4171359

SPROCKET SPROCKET, DBL

QTY ITEM PART NO.
2 16 8 2 4 2 1 4 2 2 6 16 2 2 8 2 8
2 2

DESCRIPTION

QTY

43

TINE ASSEMBLY
FIGURE 13

SA-30
2
7 6
5

1
12 18

20

8

3

4

3 4
16 3
17

14
4 19

12
22 21 10 9
11

15 13

22 21
44

10 9

SA-30

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO.

1 4171394.7 WLDMT-TINE ASSY

1

2 64197-025 BLT-TDFM 1/4-20X5/8

4

3 64141-6

NUT-WLF 5/16-18

8

4 64018-15 BLT-CRG 5/16-18X1 SN

8

5 4171363.7 PLATE-CHAIN COVER

2

6 4172290.7 DOOR-CHAIN COVER

2

7 4172291.7 COVER-CHAIN

2

8 64044-13 SCREW-SET 1/4-28X1/4

12

9 64044-18 SCREW-SET 5/16-18 x 5/16

2

10 64044-25 SCREW-SET 5/16-18X1/2

2

11 64268-02 NUT-FL NYLON LOCK 5/16-18 48

12 64164-12 KEY-1/4X1 SQ

2

13 64262-008 BLT-FLG HD 5/16-18 X 1-1/4

48

14 4168069

BEARING-1″ FLUSHMOUNT

6

(INCLUDES ITEM 8)

15 C100032 TINE, CORING 3/4

48

4173511

KIT-TINE, 48 COUNT

16 4171338.7 WLDMT-CENTER TINE SHAFT 1

17 4171329.7 WLDMT-TINE SPROCKET LH 1

18 4171321.7 WLDMT-TINE BANK LH

1

19 4171334.7 WLDMT-TINE SPROCKET RH 1

20 4171322.7 WLDMT-TINE BANK RH

1

21 4172865

LINK-CONNECTOR

2

22 4172864-02 CHAIN-50 ROLLER 63 PITCH 2

23* 4173503

KIT-CHAIN

1

(INCLUDES ALL 6 CHAINS FOR UNIT AND LINKS)

TINE ASSEMBLY

FIGURE 13

DESCRIPTION

QTY

*NOT ILLUSTRATED

45

PLATFORM, PAD & JACKSTANDS
FIGURE 14
20 30
31 21

SA-30
29 27

28

10

12

2 16
17 8

14

18

15

5

13 11

3 25 4 6 26

7 22

9

1

24

19 23

46

SA-30

PLATFORM, PAD & JACKSTANDS
FIGURE 14

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO.

1 4172224.17 PLT-JACK

2

2 4172688 PIN-JACK

2

3 4173046 BUSHING-LATCH ARM

1

4 64268-02 NUT-FL NYLON LOCK 5/16-18 1

5 64018-58 BLT-CRG 5/16-18X1-3/4

1

6 64163-108 WSHR-.334 X 1.25 X .125

1

7 4171391 BUSHING-SPACER

2

8 64262-027 BLT-FLG HD 3/8-16 X 2-1/4 GR8 2

9 64268-03 NUT-FL NYLON LOCK 3/8-16 2

10 64141-13 NUT-WLF 1/2-13

2

11 64018-45 BLT-CRG 1/2-13 X 2-1/4

2

12 4172316.7 PLT-PLATFORM BRKT

2

13 4172318.7 BRKT-BUMPER SUPPORT

2

14 64163-86 WSHR- .265 X .625 X .125

4

15 64189-16 BLT-HEX SOC 1/4-20 X 1

4

16 64229–01 NUT-NYLON LOCK 1/4-20

4

17 4172315.7 BRKT-PLATFORM DAMPER

2

18 4170585 BUMPER-RADIAL

4

19 4173515 S- PLATFORM

1

(INCLUDES ITEMS 22 & 23)

20 64262-003 BLT-FLG 1/4-20 X 1

2

21 64262-002 BLT-FLG HD 1/4-20 X 3/4

4

22 4166324-06 BEARING-SLEEVE

2

23 4170670 MAT-FOOTPLATE

1

24 4172913-1 LABEL-STAND-AER SA30

1

25 4173037.7 LATCH-PLATFORM

1

26 4171365 CAP-FOOTPLATE LATCH

2

27 4172682.7 BRKT-PAD, SUPPORT

1

28 4171885 PAD-AERATOR STAND ON GRAY 1

29 4160281 S-TUBE,DOCUMENT

1

(INCLUDES ITEMS 30 & 31)

30 2000735 LABEL-OPER MAN

1

31 38061A

CAPS VINYL

1

DESCRIPTION

QTY

*NOT ILLUSTRATED

47

COVERS & GUARDS
FIGURE 15

48

15 16
25

14

9

12 10

26

20

13

13 20
25 27
29

12

11

30 6
23 31

24

31

31

8

8

23 5

23

27 27

17

28

12
9 10

8 23
19 12
18

26

22 26
29

30

12

20 20
12 20

7

23

11

31 22

21 3
21 1
2

21

SA-30

4 21

SA-30
ITEM PART NO. DESCRIPTION

QTY ITEM PART NO.

FIGURE 15

DESCRIPTION

QTY

1 4172177.17 COVER-WEIGHT

1

2 4171538.17 PLT-WEIGHT

3

3 4172194.7 WLDMT-HITCH

1

4 4172869

PLUG-HITCH TUBE

1

5 4172703.7 PLT-WEIGHT,CENTER

5

6 4172853.17 WLDMT-COVER FRONT

1

7 64141-6

NUT-WLF 5/16-18

6

8 2183071-03 SPACER-15.88X10.32X24

4

9 64018-51 BLT-CRG 5/16-18 X 3/4 SN

14

10 4171535.17 COVER-TOP FRONT

2

11 4171537.17 COVER-FRONT, RH

1

4171536.17 COVER-FRONT, LH

1

12 38524

KNOB-4 PRONG 3/8-16

8

13 4171521.17 PLT-TINE COVER,TOP

2

14 4173507

S-FENDER, RIGHT

1

4173510

S-FENDER, LEFT

1

15 4172800.7 PLT-PIN LOCK

2

16 4171489.7 PLT-TIRE SCRAPER

2

17 4172852.17 PLT-TINE COVER, REAR

1

18 4171484.7 COVER-CHAIN, RH

1

4171483.7 COVER-CHAIN, LH

1

19 4172229.7 COVER-CHAIN,RH REAR

1

4172228.7 COVER-CHAIN,LH REAR

1

20 64268-03 NUT-FL NYLON LOCK 3/8-16 10

21 64018-31 BLT-CRG 3/8-16 X 2-1/2

4

22 64018-47 BLT-CRG 3/8-16X2-3/4

2

23 64229-03 NUT-NYLON LOCK, 3/8-16

6

24 64262-025 BLT-FLG HD 3/8-16 X 2-1/2 LG 2

25 64018-15 BLT-CRG 5/16-18X1 SN

4

26 64268-02 NUT-FL NYLON LOCK 5/16-18 12

27 64001-6

NUT-HEX JAM 3/8-16

6

28 64018-7

BLT-CRG 3/8-16X1-1/4

2

29 64018-44 BLT-CRG 3/8-16X1 SN

4

30 64018-55 BLT-CRG 3/8-16X3-1/2

4

31 2183071-02 SPACER-15.88X10.32X32

4

49

DECALS
FIGURE 16

SA-30

2 14 11
6 & 7

1 4
5

10

17 13
3

15 & 3 UNDER COVER

9 6

12 3
8
7

50

SA-30

ITEM PART NO. DESCRIPTION

QTY ITEM PART NO.

1 4172858 LABEL- CONTROL PANEL

1

2 2000570 LABEL-WARN FUEL PICT.

2

3 2000577 LABEL WARNING

3

4 2000590 LABEL WARN BATTERY

1

5 4172910 LABEL-RESERVOIR

1

6 4171963 LABELCLASSEN BLACK

2

7 4171825 LABEL-PRO

2

8 4172912 LABEL-HYDRA-COOL

1

9 4172915 LABEL-JACKSTAND

1

10 4172911 LABEL-SLOPES, CA SPARK

1

11 4172914 LABEL-TINES

1

12 4172886 LABEL-DEPTH CONTROL LH 1

13 4172887 LABEL-DEPTH CONTROL RH 1

14 4172913-1 LABEL-STAND-AER SA30

2

15 4172916 LABEL-BELT ROUTING

1

16* 2000735 LABEL- OP MANUAL

1

LOCATED ON DOCUMENT TUBE

17 4173007 DECAL-SMALL CLASSEN PRO 2

DECALS

FIGURE 16

DESCRIPTION

QTY

51

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals