MAYTAG W11401462B Top Mount Refrigerator User Guide
- June 13, 2024
- Maytag
Table of Contents
W11401462B Top Mount Refrigerator
User Guide
OPERATING INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY
INSTRUCTIONS, located in your appliance’s Owner’s Manual, before
operating this appliance.
IMPORTANT: Before operating this appliance, make sure it has been
properly installed according to the appliance’s Owner’s Manual.
Your refrigerator has two controls that affect the temperature. The
Temperature control is located at the top front of the refrigerator
compartment and the Airflow control is located on the back wall of the freezer
compartment.
**TEMPERATURE CONTROL
**
Recommended Settings
For your convenience, the temperature control is
preset at the factory. When you first install your refrigerator, make sure the
control is still preset as shown above.
IMPORTANT:
-
The recommended setting should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
-
Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer controls to a colder than recommended setting will not cool the compartments any faster. -
If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.
COOLING ON/OFF
- To turn cooling off, press and hold Temp Setting for 4 seconds until all lights stay on for 1 second. To turn cooling back on, press and hold Temp Setting again for 4 seconds.
NOTE: Neither compartment will cool when the control is set to Off.
ADJUSTING THE TEMPERATURE CONTROL
If you need to adjust the temperature in either the refrigerator or freezer
compartment, use the settings listed in the chart below as a guide.
NOTE: Except when starting the refrigerator, do not adjust the control
more than one setting at a time. Wait 24 hours between adjustments for the
temperature to stabilize
- Press the Temp Setting button to toggle among the four LED lights which indicate the temperature setting. Reading from left to right, the LED in the first position is the least cold. The LEDs indicate increasingly colder settings as you continue to the right until all four LEDs are illuminated.
NOTE: For the first to fourth setting, only one LED of the four LEDs will be lit. All four LEDs will be lit when you have reached the coldest setting.
| CONDITION/REASON: | ADJUSTMENT: |
|---|---|
| Refrigerator too warm | Temp control one setting higher |
| Refrigerator too cold | Temp control one setting lower |
| Freezer too warm/too little ice* | Airflow or Temp control one setting higher |
| Freezer too cold | Airflow or Temp control one setting lower |
*Ice makers and Ice maker kits are available on select models. See online Owner’s Manual.
Powerholder® FEATURE
The Powerholder® feature sets the freezer and refrigerator to the lowest
temperature settings to assist with periods of high refrigerator use, full
grocery loads, or temporarily warm room temperatures.
- To turn on the Powerholder® feature, press Temp Setting continually until all the LED lights are blinking on/off progressively from left to right. Press Temp Setting again to return to the Cold set point.
NOTE: Depending on the environment conditions, the PowerCold® feature
will remain activated for up to 24 hours. When the feature turns off, the
temperature will return to the recommended set point.
AIRFLOW CONTROL
The Airflow control regulates the amount of air flowing between the freezer
and the refrigerator compartments. Changing the Airflow setting to Max removes
cool air from the freezer and uses it to cool the refrigerator.
When you plug in the refrigerator for the first time, turn the Airflow control
to the Recommended setting. ADJUSTING THE AIRFLOW CONTROL
- Max – Increase airflow to the freezer
- Min – Increase airflow to the refrigerator
IMPORTANT: Once the performance is achieved, return the Airflow control to the recommended setting to keep the refrigerator operating at optimum efficiency.
| CONDITION/REASON: | ADJUSTMENT: |
|---|---|
| Heavy ice use* | Max |
| Hot room temperature | Max – to maintain ice making production rate |
| Large quantity of groceries | Min – to quickly chill food and beverages |
*Ice makers and ice maker kits are available on select models. See online Owner’s Manual.
Online Ordering Information
For detailed installation instruction and maintenance information, winter
storage, and transportation tips, please see the Owner’s Manual included with
your appliance.
For information on any of the following items, the full cycle guide, warranty,
detailed product dimensions, or for complete instructions for use and
installation, please visit https://www.maytag.com/owners, or in Canada
https://www.maytag.ca/owners. This may save you the cost of a service call.
However, if you need to contact us, use the information listed below for the
appropriate region.
United States:
1–800–344–1274
Maytag Brand Appliances
Customer experience Center
553 Benson Road
Benton Harbor, MI 49022–2692
Canada:
1–800–807–6777
Maytag Brand Appliances
Customer experience Centre
200–6750 Century Ave.
Mississauga, Ontario L5N 0B7
®/™ ©2023 Maytag. All rights reserved. Used under license in Canada.