THE HOME DEPOT 21254 3 Light Vanity User Manual

THE HOME DEPOT 21254 3 Light Vanity

Product Information

• Mounting bracket (H1) – 1 pc
• Support screw (short) (H2) – 2 pcs
• Outlet box screw (long) (H3) – 2 pcs
• Green ground screw (H4) – 1 pc
• Wire connector (H5) – 3 pcs
• Socket ring (H6) – 3 pcs

Product Usage Instructions

Preparation:

1. Prepare the mounting bracket by locating and identifying the parts: Mounting bracket (H1), Support screw (short) (H2), Outlet box screw (long) (H3), Green ground screw (H4), Wire connector (H5), and Socket ring (H6).
   Installation:

2. Install the mounting bracket using the following steps:

3. Attach the pre-assembled mounting bracket (H1) to the fixture body (A).

4. Secure the mounting bracket using the pre-assembled support screws (short) (H2).

5. Use the outlet box screws (long) (H3) to fix the mounting bracket securely to the outlet box.

6. Ensure the green ground screw (H4) is properly attached to the mounting bracket.
   Making Electrical Connections:

7. Make the electrical connections as follows:

   • Connect the black wire from the outlet box to the black wire from the fixture.
   • Connect the white wire from the fixture to the white wire from the outlet box.
     Assembling the Fixture Body to the Outlet Box:

8. Assemble the fixture body to the outlet box by aligning and securing them together. Note that the fixture can be installed facing up or facing down.
   Assembling the Glass Shades:

9. Assemble the glass shades onto the fixture body.
   Installing the Light Bulbs:

10. Install the light bulbs by following these guidelines:

    • Use three MAX 60 W medium base (E26) type A bulbs or MAX 9W medium base (E26) self-ballasted LED bulbs.
    • Do not exceed the recommended wattage.

Cleaning:
Refer to the product manual for cleaning instructions.

Troubleshooting:
Refer to the product manual for troubleshooting guidelines.

Overview

Hardware

Hardware (Parts are not to scale)

THIS MANUAL CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

IMPORTANT SAFETY INFORMATION

• Please read and understand this entire manual before attempting to assemble, operate, or install the product.
• Turn off electricity at the main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching off the circuit breaker).
• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
• All electrical connections must be in agreement with local codes, ordinances, or the National Electric Code (NEC). Contact your municipal building department to learn about your local codes, permits, and/or inspections. If you do not have electrical wiring experience, refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.
• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician before installation.
• Do not exceed the recommended wattage. Refer to the re-lamping label on the light socket for maximum wattage.
• Do not replace a bulb when the electrical outlet switch is turned to the “ON” position.
• Do not immerse your lamp in water; doing so will damage the wire.
• Keep materials that burn easily away from lighted bulbs.

PREPARATION

• Before beginning assembly, installation or operation of the product, make sure all parts are present. Compare parts with the package contents list and diagram on the previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.
• Tools required for assembly (not included): flathead screwdriver, Phillips screwdriver, pliers, electrical tape, wire cutters, safety glasses, ladder, wire stripper.

INSTALLATION

1. Preparing the mounting bracket

   • Unscrew the two support screws (short) (H2) from the mounting bracket (H1). Remove the mounting bracket (H1) from the canopy of the fixture body (A), and keep the support screws (short) (H2) for later use.

2. Installing the mounting bracket

   • Fasten the mounting bracket (H1) onto the outlet box using two outlet box screws (long) (H3).

3. Making the electrical connections

   • Strip 3/4 in. of insulation from the wire ends.
   • Connect the black wire from the fixture to the black wire from the outlet box, then connect the white wire from the fixture to the white wire from the outlet box.
   • The bare copper ground wire from the fixture must loop one turn under the head of the green ground screw (H4) on the mounting bracket (H1) before it is connected to the ground conductor of the supply circuit.
   • Cover the wires with wire connectors (H5). Tape the wire connectors (H5) and wires together, and carefully position all wires inside the outlet box.

4. Assembling the fixture body to the outlet box

   • Place the fixture body (A) over the outlet box, align the two holes of the mounting bracket (H1) and the canopy of the fixture body (A), then tighten the support screws (short) (H2).
     Note: The whole fixture can be installed facing up or facing down.

5. Assembling the glass shades

   • Unscrew the socket rings (H6) from the sockets on the fixture body (A). Set the glass shades (B) onto each socket, and secure them with the socket rings (H6).

6. Installing the light bulbs

   • Install the light bulbs (not provided) into the socket. Use three MAX 60 W medium base (E26) type “ST64” bulbs (recommended).
     Note: You can also use three MAX 60 W medium base (E26) type “A” bulbs or MAX 9W medium base (E26) self-ballasted LED bulbs. Do not exceed the recommended wattage.

CLEANING

• Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
• To clean the fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. Use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture.

TROUBLESHOOTING

• The light does not come on at all:
  • Check whether the bulbs were burned out.
  • Make sure the wall switch is on.
  • Make sure the wiring is correct.
  • Make sure the circuit breaker is set in the “ON” position.
• The fuse blows or the circuit trips when the light is turned on.
  • Check for crossed wires, and ensure the wiring is correct.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>