AWE 3010-22016 Resonated Performance Exhaust Installation Guide

June 13, 2024
AWE

**AWE 3010-22016 Resonated Performance Exhaust Installation Guide

**

THIS GUIDE IS INTENDED FOR THE FOLLOWING PART NUMBERS:

  • 3010-22020 AWE Performance Catback Exhaust for Golf/Rabbit 2.5L- Chrome Silver Tips
  • 3015-32038 AWE Performance Exhaust for VW MK5 GTI – Chrome Silver Tips
  • 3010-22016 AWE Performance Exhaust for Audi A3 FWD – Chrome Silver Tips

Welcome to the AWE family, and congratulations on your purchase of the AWE Exhaust System for the VW Rabbit, Golf, and Audi A3.

Exquisite build quality and craftsmanship, coupled with industry leading performance, distinguish this exhaust system from all others.

*For up to the minute fitment information, be sure to visit the AWE website. As always, AWE Performance Specialists are standing by for any questions, right here.

PARTS LIST

  • For Rabbit and Golf:
  • 1 front resonator section
  • 1 mid muffler inlet pipe
  • 1 mid muffler section
  • 1 mid muffler outlet pipe
  • 1 tailpipe section
  • 1 y-pipe
  • 2 3.15” (80mm) exhaust tip
  • 2 2.25” T-Bolt clamp
  • 5 2.5” (63.5mm) Accu-Seal band clamp
  • 2 hanger post clamp
  • 1 9/64” allen wrench (for hanger post clamp)

Step 1

Remove the factory cat back exhaust system. Please note that the sleeve clamp between the downpipe and the cat back exhaust is re-used when installing the AWE Tuning exhaust **(at Arrow A inFigure 1).

**

If you intend to install an AWE Tuning High Flow Downpipe or any other brand downpipe at the same time as your cat back exhaust system, it is recommended that you install the downpipe first to make cat back exhaust alignment easier.

Step 2

Once the exhaust system is properly adjusted, install a hanger post clamp on each of the hanger posts, as shown at arrow in **Figure 2.

**

Slide the clamp onto the hanger post so that it sits snug against the rubber element, and then tighten down with the enclosed allen wrench.

These clamps will keep the exhaust from sliding laterally under usage and will keep the tips properly aligned in the valence openings. Set final tip rotation, stagger, and overall length, and then tighten their T-bolt clamps.

Please note that all stainless steel exhaust systems will “grow” in length approximately 1” when fully warmed up, and you may want to adjust the tip lengths at this time in anticipation of this growth.

Step 3

For the best tip fitment, align the barrel style tip clamp to cover only the slot, shown by Arrow A Torque the tip clamp to 18 ft./lbs.

NOTES:

  • It is required to apply anti-seize to the threads to prevent thread binding, shown by Arrow B

  • It is okay to have the clamp extend beyond the edge of the tip inlet.

TROULESHTOOTING

Issue Solution
Exhaust is not fitting correctly Most fitment issues are due to improperly

adjusted exhaust. Thisincludes tip fitments and rattling due to chassis contact. Checkout our fitment guide for more installation tips.
Incorrect or missing parts| Double check the parts list for your system and compare themwith what you received. Fill out our contact form, found belowand let us know what parts you need.

CARE

Once installed properly, your AWE exhaust will provide years of trouble-free performance. The exhaust volume and sound will settle with usage; 800-1000 miles is required to break-in new exhaust systems.

Also, please note that the rear 180Technology® resonator has a small drain hole to allow condensation to escape. Water drops from this area are normal.

Periodic cleaning of exhaust tips is necessary to maintain proper finish, especially in areas prone to road salt and caustic deicing solutions. Use a mild soap and water solution or car wax to clean the finish. Avoid using abrasive polishes, as they can scratch the finish.

Any questions or comments, please do not hesitate to contact us:

AWE
215-658-1670
CONTACT FORM

Warranty

Up-to-date warranty information is found HERE.

For up-to-date fitment information, please visit the product page on AWE- Tuning.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals