YEELIGHT YLDD005 Lightstrip Pro User Manual

: June 13, 2024
: Yeelight

Table of Contents

Product Description
Setup Instructions
Instructions for Use
Parameters
Apple HomeKit Smart Control
How to Reset
Warranty Conditions
EU Declaration of Conformity
WEEE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

YEELIGHT YLDD005 Lightstrip Pro User Manual

Dear customer,

Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention to the safety instructions. If you have any questions or comments about the device, please contact the customer line.

Product Description

Product Overview

Plug will be subject to sales territory standard. Picture shown above is for reference only.
Product Description

The Extension needs to purchase separately.

Setup Instructions

Plug into the adapter, rotate by 45 degrees clockwise and snap into place.

Insert the end with 4 pins into the corresponding socket and fasten the buckle.

Clean the installation surface, paste and fix the light strip.

If the light strip needs to be extended, please purchase Yee light Light strip Pro Extension. Open the tail end buckle of the light strip, remove the tail plug, connect the end with 4 pins of the extension strip with the tail end of the original strip, and tighten the buckle.

Install the tail plug at the tail end of the extension part and fasten the buckle to complete the connection.

Connect and plug in the power supply.

To ensure that the functions can work normally:

After connecting the extension strip, ensure the tail plug is correctly plugged into the tail end of the light strip.
After cutting the light strip, set the length of the light strip in the app (Mijia app QR code.)

Instructions for Use

Tap “ ” to turn the light strip; tap “ ” again to turn off the light strip.
Tap and hold “ ” to choose your favourite colour.
Double tap “ ” to choose your favourite Dream Colour mode

Parameters

Model No.: YLDD005
Luminous Flux: 200 lm
Operating Temperature: -10 ~ 40°C
Frequency Bands: 2412MHz – 2472MHz (Wi-Fi) 2402MHz – 2480MHz (BT)
Rated Input: 24 VDC, 0.21A, 5.1W (80in, 2m) 24 VDC, 0.88A, 21W (400in, 10m)
Rated Input (Adapter): 100-240V ~ 50/60Hz, 0.06A, 5.5W (80in, 2m) 100-240V ~ 50/60Hz, 0.25A, 24W (400in, 10m)
Maximum Output Power: 18 dBm (WiFi) 6 dBm (BT)
Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4GHz, Bluetooth 4.2 BLE
System Requirements: Android 4.4 & iOS 10.0 or above Intelligent Control

This product works with Mi Home / Xiaomi Home app. Control your device, and interact it and other smart home devices with Mi Home / Xiaomi Home App.

Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search “Mi Home / Xiaomi Home” in the app Store to download and install it.
Open Mi Home / Xiaomi Home app, tap “+” on the upper right, and then follow prompts to add your device.

Note: The version of the app might have been updated, please follow the instructions based on the current app version.

Works with Mijia
“Works with Mijia” means that the product can be control by Mi Home app or Xiaomi. Please note that “Works with Mijia” only performs software-level verification. Xiaomi and Mijia are not responsible for the manufacturing, standard implementation and quality supervision of the products and enterprises.

Apple HomeKit Smart Control

Open the Home APP in your iPhone or iPad.
Click “+” button and add accessory as per the prompts in the app. Scan the QR code on the right or under the product base. Alternatively, input the 8-digit code shown above the QR code to complete the access.

Make sure the Wi-Fi network is available and you can get access to the internet properly. This product is not compatible with 5G network.
To ensure proper HomeKit compatibility, it is recommended to use iOS 9 or above.
HomeKit codes are indicated under the base of controller. Please be noted that HomeKit codes are required for reset every time.

Apple is the trade mark of Apple LLC.
Use the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Apple, HomeKit, iPad, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
To control this HomeKit-enabled accessory, the latest version of iOS or iPadOS is recommended.

Home hub
A customer who owns an Apple TV (4th generation or later) with tvOS 10 or later, an iPad with iOS or later, or a HomePod can control HomeKit-enabled accessories away from home and automatically through triggers such as time of day, location, sensor detection, or the action of an accessory.

How to Reset

Disconnect the power. Press the power button and reconnect to the power supply without release. Hold the button for five seconds until the light strip flows in red, green, and blue, and turns to yellow. Then, release the button. Reset is completed.

Please reset the light strip before using it in a new network environment.

Warnings

Check the voltage before using the product. Improper voltage may damage the product and cause potential safety hazards.
For indoor use only .
To prevent early product failure, the light strip should only be installed in operating environment ranging between 10°F to 104°F (-10°C to +40°C)
The light strip is not waterproof.
Regularly check the cable, the power supply, and all other parts. Do not use this luminaire when any part is damaged.
The external flexible cable or cord of this luminaire cannot be replaced. Do not use the luminaire when the cable or cord is damaged.
The light strip is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
Do not disassemble the product privately.
Keep the light strip away from kids under 3-year-old.
Max interconnected 40in (10m).
Do not bend the LED inside the light strip is more than 90 degrees to avoid any possible damage.
Do not connect the light strip to the power supply when it is in the package.
Interconnection shall be made only by the use of the supplied connectors. Any open end must be sealed-off before use.
Do not use the light strip when covered or recessed into a surface.
Do not open or cut the light strip.
Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.

The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
Natural wear and aging of consumables or components during use (such as batteries, etc.).
Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

EU Declaration of Conformity

Hereby, Qingdao Yeelink Information Technology Co., Ltd., declares that the radio equipment type YLD005 is in compliance with Directive 2015/53/EU.

WEEE

This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.

www.alza.co.uk/kontakt
+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz