BEG 93540 Indoor 180-BMS DALI-2 Ss Frame Multisensor Frameless Wall Mounting Instruction Manual
- June 13, 2024
- BEG
Table of Contents
LUXOMAT®
net Indoor 180-BMS DALI-2
93540
Safety instructions
| Work on the mains supply may only be carried out by qualified professionals
or by instructed persons under the direction and supervision of qualified
skilled electrical personnel in accordance with electrotechnical regulations.
---|---
| Disconnect supply before installing!
This device is not to be used to isolate other equipment from the mains
supply.
| DALI is not SELV – the installation instructions for low voltage apply.
The DALI screw clamps must not be connected to 230 VAC!
| Read this supplementary sheet and the operating instructions before putting
the device into operation. Knowledge of these documents is part of the
intended use!
Function
| DALI-2 multi sensor (Input Device) designed for in-wall mounting. Please
order cover frame separately, available in various colours. Powered via DALI
bus.
---|---
Addressable according to IEC 62386 Part 103 (control device). Instance 0
provides information regarding occupancy and movement for the DALI bus
according to IEC 62386 part 303. Instance 1 provides LUX values for the DALI
bus according to IEC 62386 part 304.
Parameter is ation is possible via mandatory Multi master-Application-
Controller of any manufacturer. This controller must support IEC 62386
parts 101/103/303/304
Mounting
Mounting hints
| Fig. A | Detector without frame |
|---|---|
| Fig. B | Mounting screws |
| Fig. C | Blind for the exclusion of interference sources |
| Fig. D | Frame |
| Fig. E | Central plate |
| Fig. F | Cover-cap |
| Fig. G | Vandal-proofing of potentiometer cover against unwanted removal |
Initial operation
| General: The device can be put into service directly after mounting,
following the software instructions from the relevant controller manufacturer.
---|---
Exclude sources of interference
Fig. C| In case the detection area of the detector is too large or areas are
being covered that should not be monitored, the range can be reduced or
limited by using the enclosed blinds.
---|---
Self-test cycle
During the first 20 sec after connecting to the DALI bus power, the product will enter a self-test cycle. During this time the device does not respond to movement.
LED function indicators
Fig. 3| • Shortly on:
A Green Movement
B Red –
C White –
• Flashing:
A Green Localisation
B Red Initialization
C White Localization
D Red Localization
---|---
Technical data
| Settings: via application which supports DALI multisensory (IEC 62386 parts
101/103/303/304).
---|---
DALI-BUS
max. 22.5 V| Voltage
7 mA| Typ. power input
0.5 W| Power consumption
0.5 – 2.5 mm2| Terminal clamps:
for solid one-wire conductors
180°| Area of coverage
1 m / 2.2 m / 1.1 m| Mounting height min./max./
recommended
Fig. 4
1.1 m
18°C
1 = max. 10 m
2 = max. 3 m| Range of coverage at
mounting height
Ambient temperature
1 across
2 towards
157 m2| Monitored surface, when the detector is mounted at 1.1 m mounting
height and for tangential
approach
II / IP20| Class / Degree of protection
70 x 70 x 61 mm| Dimensions
-25°C – +50°C| Ambient temperature
0 – 4095 Lux| Measured light output
Schematic diagram
Schematic diagram – when connecting the detector, please respect the labelling
of the terminal connections at the device!
UK Declaration of conformity
This product respects the directives concerning
- Electrical Equipment Safety Regulation 2016
- Electromagnetic Compatibility Regulation 2016
- The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation 2012
Contact
B.E.G. UK Ltd., Apex Court – Grove House • Camphill Road • West By fleet,
Surrey KT14 6SQ
Accessory
| 92630 | Covering IP20 pure white, mat, RAL9010 |
|---|---|
| 92631 | Covering IP20 traffic white, mat, RAL9016 |
| 92632 | Covering IP20 oyster white, mat, RAL1013 |
| 92633 | Covering IP20 silver, mat, RAL9006 |
| 92634 | Covering IP20 anthracite, mat, RAL7021 |
| 92139 | Covering IP54 pure white, mat, RAL9010 |
| 92141 | SM-Socket for Indoor 180 pure white, brilliant, RAL9010 |
| 39222 | Central plate pure white, brilliant, 55 x 55 mm, RAL9010 |
| 39242 | Zentralplatte pure white, brilliant 55 x 55 mm, oval, RAL9010 |
| 39223 | Central plate traffic white, brilliant, 55 x 55 mm, RAL9016 |
| 35126 | Central plate pure white, brilliant 56 x 56 mm, angular, RAL9010 |
| 35127 | Central plate pure white, brilliant 56 x 56 mm, rounded, RAL9010 |
| 38947 | Central plate traffic white, mat, 45 x 45 mm, RAL9016 |
| 39076 | Central plate cream white, mat, 45 x 45 mm, RAL9001 |
| 92294 | Blinds vertical/ horizontal detection, transparent |
Trouble shooting
| 1. Power consumption on DALI line too high
Please be aware of the total power consumption of all the DALI units in your
system.
---|---
2. Heat sources in the vicinity If, for example, the detector is located in
the immediate vicinity of ventilation slits
or a projector, the warm air currents can trigger motion detection. Place the
detector at a sufficient distance from potential sources of interference such
as ventilation slits, projectors, beamers, etc.
| Product page on the internet
https://www.beg-luxomat.com/qr.php?prtno=93540
Brück Electronic GmbH I Gerberstr. 33 I 51789 Lindlar I GERMANY I Phone: +49 (0) 2266 90121-0 I Fax: +49 (0) 2266 90121-50 I info@beg.de I beg-luxomat.com
Subject to technical changes
93540M1_Short_MAN_Indoor 180-BMS DALI-2_de_uk_fr_nl_V2 – 14102021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>