modular 70-40 CPE Heated Pasta-Cooker Instruction Manual

: June 4, 2024
: MODULAR

Table of Contents

modular 70-40 CPE Heated Pasta-Cooker
GENERAL PRESCRIPTIONS
DISPOSAL OF PACKING AND OF THE APPLIANCE
SAFETY DEVISES SAFETY THERMOSTAT
INSTRUCTIONS FOR INSTALLATION
CONNECTIONS
CONVERSION TO ANOTHER TYPE OF GAS
COMMISSIONING
INSTRUCTIONS FOR USE
FILLING AND EMPTYING OF THE TANK
FILLING AND EMPTYING OF THE TANK
INSTRUCTIONS FOR CLEANING
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

modular 70-40 CPE Heated Pasta-Cooker

GENERAL PRESCRIPTIONS

READ THIS MANUAL CAREFULLY. IT PROVIDES IMPORTANT INFORMATION FOR THE SAFE INSTALLATION, USE, AND MAINTENANCE OF THE APPLIANCE.
FAILURE TO COMPLY WITH WHAT IS PRESENTED BELOW MAY COMPROMISE THE SAFETY OF THE EQUIPMENT. THE MANUFACTURER WILL NOT BE LIABLE FOR ANY DAMAGE OR INJURY RESULTING FROM FAILURE TO OBSERVE THE FOLLOWING RULES.
TRANSLATION OF THE ORIGINAL INSTRUCTIONS.
APPLIANCES NEED PRECAUTIONS FOR INSTALLATION, PLACING, AND/OR FIXATION AND CONNECTION TO THE MAINS.
SEE SECTION “INSTALLATION INSTRUCTIONS” THE APPLIANCES NEED PRECAUTIONS FOR CLEANING. SEE THE SECTION ” INSTRUCTIONS FOR CLEANING”.
THE SYMBOL ” HIGH VOLTAGE” IS PLACED ON A PANEL THAT GIVES ACCESS TO A PART WITH HIGH VOLTAGE.
THIS EQUIPMENT IS DESIGNED FOR cOMMERCIAL SETTINGS, FOR EXAMPLE, RESTAURANT KITCHENS, CANTEENS, HOSPITALS, OR COMMERCIAL ENTERPRISES SUCH AS BAKERIES, BUTCHERIES ECT.
BUT IT IS NOT DESIGNED FOR MASS PRODUCTION OF FOOD.
THESE PIECES OF EQUIPMENT ARE DESIGNED FOR FOOD FRYING AND FOR PROFESSIONAL USE. OTHER USES ARE NOT APPROPRIATE.
DO NOT CLEAN THE EQUIPMENT WTH DIRECTS WATER JETS, HIGH PRESSURE, OR STEAM CLEANER.
RESTORE THE OIL BATH WHENEVER IT FALLS BELOW THE MIN.
LEVEL, MARKED BY THE SPECIAL REFERENCE NOTCH. IRE)
FOR BETTER PERFORMANCE OF THE APPLIANCE, REGULARLY CHANGE THE OIL USED. OVERUSING AN OIL REDUCES ITS
FLASHPOINT AND INCREASES ITS TENDENCY TO BOIL SUDDENLY.
MIND THE EFFECTS THAT MOIST FOOD OR A BIG QUANTITY OF FOOD MIGHT HAVE ON THE SUDDEN BOILING OF OIL.

Keep this manual in a safe place, known to all users, so that it can be consulted throughout the working life of the appliance. This equipment is designed for cooking food. It is intended for industrial use. Any other use is to be considered improper This appliance is not intended for use by people (including children) with limited physical, sensory or mental abilities or without experience and knowledge of it. Unless they are supervised or instructed in its use by a person responsible for their safety. Do not leave the de-appliance unattended in presence of children and ensure that the latter do not have access to the appliance. The appliance must be used by a trained person Do not leave the appliance unattended when operating.

DO NOT STORE ” FLAMMABLE MATERIALS IN CLOSE PROXIMITY TO THE APPLIANCE. FIRE HAZARD.

The appliance must be installed in a well-ventilated room. Inadequate ventilation causes asphyxia. Do not obstruct the ventilation system of the place where the appliance is installed. Do not obstruct the vents or ducts of this or other appliances. In the event of an appliance fault or malfunction, shut the gas shut-off valve and/or switch the appliance off at the main switch installed upline. Installation and conversion to a different type of gas must be carried out by qualified technicians authorized by the manufacturer, in compliance with current safety standards and the instructions in this manual. Appliance maintenance and conversion to a different type of gas must be carried out by qualified technicians authorized by the manufacturer, in compliance with current safety standards and the instructions in this manual. Clean the appliance following the instructions are given in Chapter ” INSTRUCTIONS FOR CLEANING”.

DISPOSAL OF PACKING AND OF THE APPLIANCE

PACKING

The packing is made using environmentally friendly materials.
The plastic recyclable components are the transparent cover, the bags containing the instructions manual, and nozzles (made of Polyethylene – PE).
the straps (in Polypropylene PP).

APPLIANCE

The appliance is manufactured 90% from recyclable metals (stainless steel, aluminum sheet, copper.
The appliance must be scrapped in compliance with current regulations governing such disposal.
Make the appliance unusable before scrapping It must be disposed of properly.

HE SYMBOLS SHOWING A CRoSSED-OUT VASTE CONTAINER ON THE UNIT OR PACKAGE INDICATES THAT AT THE END F ITS LIFE CYCLE, THE PRODUCT MUST E COLLECTED SEPARATE FROM OTHER WASTE. THE DIFFERENTIATED COLLECTION OF THIS EQUIPMENT IS ORGANISED AND MANAGED BY THE PRODUCER. THE USER WHO INTENDS TO GET RID OF THIS EQUIPMENT SHALL CONTACT THE PRODUCER AND FOLLOW THE SYSTEM THAT THE LATTER HAS USED IN ORDER TO COLLECT THE EQUIPMENT SEPARATELY AT THE END OF ITS LIFE. PROPER SEPARATE cOLLECTION HELPS PREVENT POSSIBLE NEGATIVE IMPACTS ON THE ENVIRONMENT AND HEALTH AND FAVOURS THE REUSE AND/OR RECYCLING OF THE UNIT’S MATERIALS. ABUSIVE DISPOSAL OF THE PRODUCT BY THE HOLDER WILL RESULT IN THE APPLICATION OF PENALTIES AS PER CURRENT STANDARDS.

SAFETY DEVISES SAFETY THERMOSTAT

The manufacturer will not be liable for any damage or injury resulting from failure to observe the following rules. The appliance is equipped with a manual reset safety thermostat that interrupts heating when the operating temperature exceeds the maximum permitted value.

TO RESTORE APPLIANCE OPERATION, A OPEN THE DOOR AND PRESS THE THERMOSTAT RESET BUTTON. THIS PROCEDURE MUST ONLY BE CARRIED OUT BY A QUALIFIED, AUTHORIZED TECHNICIAN.

INSTRUCTIONS FOR INSTALLATION

REMINDERS FOR THE INSTALLER

READ THIS MANUAL CAREFULLY.
IT PROVIDES IMPORTANT INFORMATION FOR THE SAFE INSTALLATION, USE, AND MAINTENANCE OF THE APPLIANCE.
FAILURE TO COMPLY WITH WHAT IS PRESENTED BELOW MAY COMPROMISE THE SAFETY OF THE EQUIPMENT.
THE MANUFACTURER WILL NOT BE LIABLE FOR ANY DAMAGE OR INJURY RESULTING FROM FAILURE TO OBSERVE THE

FOLLOWING RULES.

identify the specific appliance model.
The model number is detailed on the packing and on the appliance data plate.
The appliance must be installed in a well-ventilated room.
Installation and conversion to a different type of gas must be carried out by qualified technicians authorized by the manufacturer, in compliance
with current safety standards and the instructions in this manual.
Appliance maintenance and conversion to a different type of gas must be carried out by qualified technicians authorized by the manufacturer, in compliance with current safety standards and the instructions in this manual.
Do not obstruct any air vents or drains present on the appliance.
Do not tamper with appliance components.

REFERENCE STANDARDS AND LAWS

Install the appliance in accordance with the safety standards in force in the country.

UNPACKING

Check the state of the packing and in the event of damage, ask the delivery person to inspect the goods.
Remove the packing.
Remove the protective film from the outer panels.
Use a suitable solvent to remove any residual adhesive from the panels.

POSITIONING

The overall dimensions of the appliance and the position of connections are given on the installation diagram at the end of this manual. – The appliance can be installed singly or in combination with other appliances in the same product range.

The appliance is not suitable for integrated installation. Position the appliance at least 10 cm from adjacent walls.
If the appliance is to be placed near walls, dividers, kitchen furniture, decorative elements, etc. this must be made of non-combustible materials
Otherwise, they must be covered with suitable non-combustible heat insulating materials. Level the appliance by means of the height-adjustable feet

APPLIANCE ASSEMBLY WITH BASE AND BRIDGE

Follow the instructions provided with the type of support utilized.

FUMES EXHAUST SYSTEM
Create a fumes exhaust system based on the ” Type ” of the appliance. The” Type ” is stated on the appliance data plate.

“A1 ” TYPE APPLIANCE
Position the “A1” type appliance below an extractor hood to ensure smoke and fumes generated by cooking are removed.

“B21 ” TYPE APPLIANCE
Position the “B21” type appliance below an extractor hood.

“B11 ” TYPE APPLIANCE
Fit the “B11” type appliance with a suitable flue, available from the appliance manufacturer. Follow the assembly instructions provided with the flue. Connect the flue to a 150/155 mm diameter hose, heat resistant to 300°C. Vent to the outside or into an efficient flue. The hose length must not exceed 3 meters.

CONNECTIONS

The position and dimensions of connections are given in the installation diagram at the end of this manual.

CONNECTION TO THE GAS SUPPLY
Check that the appliance is designed to operate with the type of gas supply present on site. Check the information given on the decals on the packing and appliance. Convert the appliance to the local gas type, if necessary. Follow the instructions in the next paragraph “Conversion to a different type of gas”.

On top of appliances, a rear connection is also available.
Remove the plug present and screw it tightly onto the front connector. A rapid-action g as shut-off valve must be fitted upstream of the appliance in an easily accessible position.
Do not use connection pipes having a diameter Smaller than that of the appliance’s gas connector Once the appliance has been installed, check for gas leaks at the connection points.

ELECTRICAL CONNECTIONS

Check if the appliance is designed to operate at the voltage and frequency of the power supply present on site.
Check the details given on the appliance data plate and plaque near the terminal board.
Install upstream of the equipment in an easily accessible place, an all-pole disconnecting device with a contact gap allowing full disconnection under the conditions of overvoltage category.
A flexible rubber cable with insulation specifications not lower than type H05 RN-F must be used for a connection.
Connect the power supply cable to the terminal board as shown in the wiring diagram supplied with the appliance. Secure the power supply cable with the cable clamp.
Protect the power supply cable on the outside of the appliance with rigid plastic or metal pipe.
If the power supply cable is damaged, it must be replaced by the manufacturer or his service center or by a person with similar qualifications to prevent any risk.

THE SYMBOL ” HIGH VOLTAGE” IS PLACED ON A PANEL THAT GIVES ACCESS TO A PART WITH HIGH VOLTAGE.

PROTECTIVE EARTH AND EARTH BONDING CONNECTIONS

Connect the appliance to an efficient ground circuit. Connect the earth conductor to the terminal with the symbol next to the main terminal board.
Connect the metal structure of the appliance to the equipotential node. Connect the conductor to the terminal with the symbol on the outside part of the bottom.

CONNECTION TO THE WATER SUPPLY

The appliance must be connected to a potable water supply.
The water inlet pressure must be between 150 kPa and 300 KPa.
Use a pressure reducer if the inlet pressure is above the maximum permitted level. Install a mechanical filter and a shut-off valve upstream of the appliance at an easily accessible point.
Make sure the water circuit is free of ferrous particles before connecting the filter and the appliance.
Seal any unused connectors with a plug.
Once the appliance has been installed, check for gas leaks at the connection points.

CONNECTION TO THE WATER DRAIN

The water drainage system must be made using materials resistant to temperatures of 100 C.
The bottom of the appliance must not be subjected to steam produced by the drainage of hot water. Install a siphoned floor drain with grating below the water drain cock of Boiling pans and in front of Bratt pans.

CONVERSION TO ANOTHER TYPE OF GAS

The table specifies: which gas can be used for the appliance.
the nozzles and settings for each gas that can be used.
For nozzles, the number indicated in table TAB1 is also stamped on the body of nozzles.
To convert the appliance to the local gas type, follow the instructions given in TAB1 and carry out the steps below: – Replace the main burner nozzle (UM). Adjust the main burner’s air regulator to distance.
Replace the main burner nozzle (UM). Adjust the main burner’s air regulator to distance A.
Replace the pilot burner nozzle (UP). Adjust the pilot burner air ” ow (if necessary). Replace the gas valve with a minimum nozzle (Um).
Affix the adhesive tab indicating the new type of gas used.
The nozzles and adhesive tabs are supplied with the appliance.

REPLACING THE NOZZLE AND THE MAIN BURNER PRIMARY AIR REGULATION

Slacken screw V.
Remove nozzle UM (fitted to air regulator 2) and replace it with the one indicated in table TAB1.
Retighten nozzle UM (fitted to air regulator Z).
Adjust air regulator Z to distance A as shown in table TAB1. Retighten screw V fully. Reassemble all parts. For assembly, proceed in reverse order.

REPLACING THE PILOT BURNER NOZZLE

Remove the front panel.
Open the door. Undo connector R.
Remove nozzle UP and replace it with the one indicated in table TAB1. Retighten connector R.
Reassemble all parts. Following, in reverse order, the sequence used for their removal.

COMMISSIONING

Following installation, conversion to a different type of gas, or any maintenance operations, check appliance operation. In the event of any malfunction, consult the next Paragraph Troubleshooting

GAS APPLIANCES

Switch on the appliance as directed in the instructions and reminders for use given in Chapter “INSTRUCTIONS FOR USE ” and check the gas supply pressure (see next Paragraph). the correct ignition of the burners and the effectiveness of the fumes removal system.

CHECKING THE GAS SUPPLY PRESSURE

To measure the gas supply pressure using a manometer with a minimum definition of 0,1 bar.
Remove the control panel
Remove the screw from on pressure test point PP and connect the manometer to the test point. Make the measurement with the appliance in operation.

IMPORTANT! IF THE GAS SUPPLY PRESSURE IS NOT WITHIN THE LIMITS (MIN. MAX) INDICATED IN TABLE TAB2 CEASE OPERATION OF THE APPEARANCE AND CONTACT THE GAS UTILITY COMPANY.

Disconnect the manometer and reignite the retaining Screw on the pressure connection. ELECTRIC EQUIPMENT Switch on the appliance as directed in the instructions and reminders for use given in Chapter “INSTRUCTIONS FOR USE and check the current values of each phase. the correct operation of the heating elements.

INSTRUCTIONS FOR USE

REMINDERS FOR THE USER TO READ THIS MANUAL CAREFULLY.
IT PRoVIDES IMPORTANT INFORMATION FOR SAFE INSTALLATION, USE, AND MAINTENANCE OF THE APPLIANCE.
THE MANUFACTURER WILL NOT BE LIABLE FOR ANY DAMAGE OR INJURY RESULTING FROM FAILURE TO OBSERVE THE FOLLOWING RULES.

For after-sales service, contact technical assistance centers authorized by the manufacturer and demand the use of original spare parts. ave the appliance serviced at least twice a year. Opens Taking outa service he a meet professional use and e oPEtded oy ruined pes he restrictions for use. Any other use oking for as 0 USe. Any other use is considered to be improper. Do not allow the appliance to operate empty for prolonged periods. only pre-neat the oven Just before Use. Do not leave the appliance unattended while in operation. In the event of an appliance fault or malfunction, shut the gas shut-off valve and/or Switch the appliance off at the main switch installed upline. Clean the appliance following the instructions given in Chapter

INSTRUCTIONS FOR CLEANING” DO NOT STORE ” FLAMMABLE MATERIALS IN CLOSE PROXIMITY TO THE APPLIANCE HAZARD.

Do not obstruct any air vents or drains present on the. appliance. Do not tamper with appliance components. Keep this manual in a state place, known to all Users, so that it can be consulted throughout the working life of the appliance. Installation and appliance maintenance must be carried out by qualified technicians authorized by the manufacturer, in compliance with current safety standards and the instructions in this Appliance maintenance and conversion to d qualified technicians authorized by the manufacturer, in compliance with current safety standards and the instructions in this manual.

USING THE GAS PASTA COOKER

The appliance is designed for boiling pasta, rice, vegetables and similar foodstuffs in water.
Do not light the pilot burner or leave it on when there is no water in the well.
While the pasta cooker is on, the water level must be maintained level with or above the minimum level indicated on the rear wall of the well.
Use very fine grained salt, adding it to the well when the water is boiling. Do not use coarsegrained rock salt in the well.
At the end of each day, clean the well thoroughly in order to prevent the formation of corrosive deposits.

FILLING AND EMPTYING OF THE TANK

Filling

Turn handle ” H ” of the drain valve anticlockwise.
The drain is completely closed only when the handle is in the horizontal position.
Turn the water tap knob to refill the well with the same quantity of water evaporated during cooking.
Water comes out of the nozzle, which can be placed under the draining surface.
Fill the well until the water is level with or above the minimum level (bottom mark) indicated on the rear wall of the well.
To halt filling, turn the knob clockwise.

Emptying

Turn the handle ” H” of the drain valve clockwise.
The drain is completely open when the handle is in the vertical position.

BURNER IGNITION AND EXTINCTION

The gas tap control knob has the following positions:

PILOT IGNITION

Press and turn knob to “pilot on”.
Press the knob down fully and light the pilot using the piezoelectric igniter.
Hold the knob down for about 20 seconds before releasing it. If the pilot flame goes out, repeat the operation.
The pilot flame can be seen through the peephole.

MAIN BURNER IGNITION

To light the main burner, turn the knob from “pilot on” to “max. flame”.
Next, depending on cooking requirements, turn the knob to any position between ” max. flame ” and ” min. flame”.

TURNING OFF

To switch the main burner off, turn the knob to position” pilot on”
To switch off the pilot flame, press and turn the knob to position ” Off”.

COOKING

Fill the well.
Light the burners.
Adjust the heating accoding to your cooking requirements.

AT THE END OF SERVICE

Switch the burners off.
Empty the well completely.

USING THE ELECTRIC PASTA CoOKER

The appliance is designed for boiling pasta, rice, vegetables and similar foodstuffs in water. While the pasta cooker is on, the water level must be maintained level with or above the minimum level indicated on the rear wall of the well. Use very fine grained salt, adding it to the well when the water is boiling. Do not use coarsegrained rock salt in the well. At the end of each day, clean the well thoroughly in order to prevent the formation of corrosive deposits.

FILLING AND EMPTYING OF THE TANK

FILLING

Turn handle ” H ” of the drain valve anticlockwise.
The drain is completely closed only when the handle is in the horizontal position.
Turn the water tap knob to refll the well with the same quantity of water evaporated during cooking.
Water comes out of the nozzle, which can be placed under the draining surface.
Fill the well until the water is level with or above the minimum level (bottom mark) indicated on the rear wall of the well.
- To halt filling, turn the knob clockwise.
- When using 600 series equipments, provided with dispenser, make sure that the drain in the front part is closed. After that fill up the tank.

EMPTYING

Turn the handle ” H” of the drain valve clockwise.
The drain is completely open when the handle is in the vertical position.
The 600 and 700 series equipments are provided with frontal drain and drainpipe with bayonet cap.
Once inserted the drain, turn left the lever placed on the equipment front part. When the lever is completely turned left the drain appears completely open.

SWITCHING ON AND OFF

The control knob has the following positions:

SWITCHING ON

Press and turn the knob from position” 1 ” to position”3″.
The yellow indicator light switches on.

TURNING OFF

Turn the knob to position “0”.
The yellow indicator light switches of.

COOKING

Fill the well.
Adjust the heating according to your cooking requirements.

AT THE END OF SERVICE

Turn the knob to position “0”.
Empty the well completely.

PROLONGED DISUSE

Before any prolonged disuse of the appliance, proceed as follows:

Clean the appliance thoroughly.
Rub stainless steel surfaces with a cloth soaked in vaseline oil to create a protective film.
Close cocks or main switches ahead of the appliances.

Following prolonged disuse, proceed as follows:

Inspect the appliance thoroughly before using it again. Allow electric appliances to operate at the lowest temperature for at least 60 minutes. V.

INSTRUCTIONS FOR CLEANING

REMINDERS FOR CLEANING EAD

THIS MANUAL CAREFULLY.
PROVIDES IMPORTANT INFORMATION FOR SAFE INSTALLATION, USE, AND MAINTENANCE OF THE APPLIANCE.
THE MANUFACTURER WILL NOT BE LIABLE FOR ANY DAMAGE OR INJURY observing THE FOLLOwING RULES. DISCONNECT
THE APPLIANCE ELECTRIC 1 SUPPLY, IF PRESENT, BEFORE CARRYING OUT ANY OPERATION

Clean the satin finish stainless steel exterior Surfaces, the cooking wells, and the surface of the not Lindsey At least twice a year, have an authorized technician clean the internal parts of the appliance. Do not use corrosive products to clean the Our beneath the appliance. Do not use direct or high- pressure water jets to clean the appliance.

SATIN FINISH STAINLESS STEEL SURFACES
Clean the surfaces with a cloth or sponge using water and proprietary non- abrasive detergents. follow the direction of the satin finish lines. Rinse repeatedly and dry thoroughly. Do not use pan scourers or other iron items. Do not use chemical products containing chlorine. Do not use sharp objects which might scratch and damage the surfaces.

THE COOKING WELLS
Clean the wells by bringing the water to a boil, Remove any limescale deposits with a proprietary limescale remover.

INSTRUCTIONS FOOR MAINTENANCE
REMINDERS FOR THE MAINTENANCE TECHNICIAN THE MANUFACTURER WILL NOT BE ! LIABLE FOR ANY DAMAGE OR INJURY UNDER THE FOLLOWING RULES. OBSERVE THE FOLLOWING RULES.

identify the specific appliance model. The model number is detailed on the packing and must De installed in a well DOnot obstruct any air vents or drains present Oppland per with appliance components. delete dnd conversion to car la throat fact safety standards and the instructions in this manual.

CONVERSION TO ANOTHER TYPE OF GAS
See Chapter ” Instructions for installation “.

COMMISSIONING
See Chapter ” Instructions for installation “.