ENDON 97647 Semi Flush Light Fitting Instruction Manual

: June 13, 2024
: ENDON

Table of Contents

ENDON 97647 Semi Flush Light Fitting
Product Usage Instructions
Safety Warnings
Care and maintenance
Troubleshooting
Assembly Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ENDON 97647 Semi Flush Light Fitting

ENDON-9764- Semi-Flush-Light-Fitting-PRODUCT

Product Information

The Semi Flush Light Fitting is designed to provide illumination in various indoor spaces. It is important to adhere to the safety instructions and guidelines provided to ensure proper installation and usage.

Safety Warnings

Never put anything on the product or hang anything on any part of this product.
Ensure that all electrical connections are tight and that no loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label as these may cause overheating and damage the fitting.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Care and Maintenance

For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down. (Caution: bulb gets hot during use).
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.

Troubleshooting

When the bulb does not light after installation:
- Ensure there is no electricity failure.
- Ensure all the connections are secure.
If you have any doubt about installation/use of this product, consult a qualified electrician.

Product Usage Instructions

Before starting the installation, ensure that the power supply to the area is turned off.
Refer to the assembly instructions provided in the manual for step-by-step guidance on how to assemble the Semi Flush Light Fitting.
Ensure all electrical connections are made securely and no loose strands are left out of the terminal.
Install bulbs of the specified wattage as indicated on the label. Using higher wattage bulbs may cause overheating and damage to the fitting.
After installation, switch on the power supply and test if the bulbs light up properly.
If the bulbs do not light up, check for any electricity failures and ensure all connections are secure.
If you encounter any difficulties or have doubts during the installation or usage of the product, it is recommended to seek assistance from a qualified electrician.

Safety Warnings

These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician.
This product is only suitable for connection to a 220-240V~ 50Hz supply in accordance with current IEE wiring regulations, and should be installed in accordance with local building regulations. It is for domestic ceiling use only, and is not suitable for a bathroom location.

This is a Class I product and must be Earthed. The terminal blocks are supplied according to requirements of the fitting.

IMPORTANT: Always switch off the mains supply during installation or maintenance. We recommend that the fuse is withdrawn or the circuit breaker switched off at the distribution board whilst work is in progress (turning off the light switch is not sufficient). Connection should be via a wall switch to enable safe isolation.

The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings are not supplied and must be purchased.
Decide on the position of the light fitting or remove existing light fitting. Note the position of the electrical connections, and ensure there is a solid mounting surface, Preferably a wooden joist or joist bridge, to support the weight of the light fitting.
Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
Never put anything on the product or hang anything on any part of this product.

IMPORTANT:

Ensure that all electrical connections are tight and that no loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label (as these may cause over heating and damage the fitting).
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or local store for recycling advice

Care and maintenance

For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use).
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.