PeakTech 5600 Video Borescope Inspection Camera User Manual

: June 4, 2024
: PeakTech

PeakTech 5600 Video Borescope Inspection Camera

Safety precautions
This product complies with the requirements of the following directives of the European Union for CE conformity: 2014/30/EU (electromagnetic compatibility), 2011/65/EU (RoHS). To ensure safe operation of the equipment and eliminate the danger of serious injury the following safety precautions must be observed. Damages resulting from failure to observe these safety precautions are exempt from any legal claims whatever.

Do not subject the equipment to direct sunlight, extreme temperatures, extreme humidity or dampness
Do not operate the equipment near strong magnetic fields motors, transformers etc.
Keep hot soldering iron or guns away from the equipment
allow the equipment to stabilize at room temperature before taking up measurement important for exact measurement.
Do not modify the equipment in any way
Opening the equipment and service and repair work must only be performed by qualified service personnel
Treat electronic equipment carefully.
Avoid harder knocks, blows or falls.
Avoid also the penetration of water and moisture to prevent damage to the sensitive device
Check device and other accessories for possible damages before operation. If in doubt, do not measure.
The measurement instrument is not to be to operated unattended.
Fetch out the battery when the meter will not be used for long period.
Periodically wipe the cabinet with a damp cloth and mid detergent.
Do not use abrasives or solvents.
The meter is suitable for indoor use only
Do not store the meter in a place of explosive, inflammable substances.
Always observe all the safety instructions printed on the device and in the operating instructions manual
Prevent from contact of metallic conductors of the device with voltage carrying components.
Perform inspections of electrical installations only by using all safety rules
Measuring instruments don’t belong to children hands.

Cleaning the cabinet

Clean only with a damp soft cloth and a commercially available mild household cleanser. Ensure that no water gets inside the equipment to prevent possible shorts and damage to the equipment.

General Specifications

This video endoscope camera offers a variety of outstanding technical properties such as the removable monitor which can be connected via video cable or the high resolution camera with 6 dimmable LEDs for illumination, which can take photos and videos to a SD card. The 8.2mm diameter of the flexible camera is also small enough to move through the smallest openings.

Removable, wired 3.5 color TFT display
HD 720p video recording and 3 Megapixel photo function
4 GB micro SD card for recording enclosed
8,2mm Camera with 6 dimmable LEDs for illumination
Additional LED flashlight function
Picture flipping/mirroring in 4 steps
S-Video output for displaying images on TV.

Description

1	Terminals for Remote-Link, AV-Out and USB-interface
2	Function keys to select the view mode for taking pictures, video

recordings, and zoom settings menu
3| Removable LCD monitor with built-in SD card slot and reset button
4| ON/OFF switch:

Rotary switch below the monitor

5| Connector for flexible camera
6| Push button for power on/off of the flashlight
7| Battery compartment

| ****

Link port

| Port for connecting cable to

the camera component (at removed Monitor)

---|---|---
AV- OUT| External monitor or television
USB| Data connection to PC

| ****

Snap

| Press to perform Photo / Video recordings

OK

| To confirm various settings

Up / Zoom

| Use arrow in several menus to choose settings and in camera mode to zoom the picture.
Down / Mirroring (Flip)| Use arrow in several menus to choose settings and in camera mode to flip the picture.
Menu| Opens the Settings menu

Mode

| Photo / Video / Playback switch

| ****

TF Card Slot

| ****

Section for Micro-SD card

Slide Lock| Slide switch to remove the display from the camera part

Reset

| ****

Reset button to reset the device

| ****

Power ON

| ****

Rotary switch below the monitor. Switch upward to turn the unit on. Next rotate upward to turn on the lighting LEDs placed on the camera. Turn knob up and down to dim the LEDs or completely turn down to turn the power off again.

---|---|---

| ****

Camera Connection

|

Plug the flexible camera with the guidance in the holder provided. Turn the nut on the thread of the camera to fix the attachment. To release the camera, turn the nut in the opposite direction and pull the camera back from the connector.

| ****

Flashlight

|

Press the trigger to activate the flashlight. This additional lighting is switched independently from the camera lighting, which is regulated over the dimmer item 4: Power ON. To switch off the flashlight, press the trigger again.

| ****

Battery

| Carefully slide the cap forward until it jumps to the top of the guide rail. Remove dead batteries and insert new batteries into the battery compartment.

Pay attention to the correct polarity as shown in the illustration

Controls

Load TF-Card

Load the TF-Card

Remove the monitor using the slide switch (3) from the main unit. Open the cover as shown in the picture and slide the TF-card into the holder provided. In delivery state, the SD card is already inserted in the device.Turn off the unit before removing the SD card. Please handle the sensitive components and contact grinders with care.

Display symbols and Menus

1.	Mode	Icon for photo / video recording / playback
2.	Battery Status	Full / Medium / Low / none
3.	SD card status	Card inserted / No Card
4.	Time and date	Displays the current time and date
5.	Function Notes	Line provides information on available key

functions

VIDEO MODE

Press the CAMERA button to take pictures in photo mode or to start video recording in video mode.

Use the OK button to freeze the image on the screen.
Use the ▲ button to zoom the image in 4 steps.
Use the ▼ button to flip the image in 4 steps.
Press the MODE button to switch between modes: Photo, Video and Playback.

Symbols in the display

Photo
Video
Playback

Press the button in photo mode to enter the menu settings for Photo or in Video mode to enter the setup menu for video recording.
Press OK to enter the general settings menu.
Use the ▲ and ▼ buttons to select the desired item and press the OK button to confirm.
Finally, press the O button again to exit the menu and switch back to the normal camera mode.

Here you can find various settings for photo resolution, color scheme, and whether the time and date should be displayed in the photo.

Here you can find various settings for video resolution, color scheme, and whether the time and date to be shown in the photo.

Set in this menu, the settings for playback of video footage and the number of displayed thumbnails. In this menu you can also delete any or all of the stored files.

General Settings

Press the O button and then press the MODE button to switch to the general settings menu. In the general settings menu you can change the settings for date / time, the menu language used, the TV system for the TV-OUT port, and the issuance of Notice noises. Furthermore, settings for refresh rates, Auto power off, format the memory card, and a recall to factory settings can be performed.

Specifications

Monitor

Russian, Japanese

Terminals| Remote, AV-OUT, SD-Card, Mini-USB

Camera

General

LED

Flashlight

| 1 W CREE LED
Operating temperature| 0°C bis 45°C (32°F … 113°F)
Power Source| 4 x 1,5V AA batteries
Weight| 445g
Dimensions Device

W x H x D

| 95 x 240 x 120mm
Dimensions Box

W x H x D

| 360 x 400 x 130mm

Accessories

| Borescope, Manual, Camera with flexible shaft,

Hook- and Magnet Set, Video-Out cable, Remote cable, Carrying case, microSD- Card

Maintenance of the unit

Do not store or operate the appliance in places where the unit is exposed to direct sunlight for a longer time.
The device must be opened and repaired only by qualified personnel.
If dirty, wipe the unit with a damp cloth, but avoid the ingress of water.
Use no aggressive detergent.

Statutory Notification about the Battery Regulations

The delivery of many devices includes batteries, which for example serve to operate the remote control. There also could be batteries or accumulators built into the device itself. In connection with the sale of these batteries or accumulators, we are obliged under the Battery Regulations to notify our customers of the following

Return them to a local shop at no cost.
The disposal in domestic refuse is strictly forbidden according to the Battery Regulations.
You can return used batteries obtained from us at no charge at the address on the last side or by posting with sufficient stamps.

Batteries, which contain harmful substances, are marked with the symbol of a crossed-out waste bin, similar to the illustration shown left. Under the waste bin symbol is the chemical symbol for the harmful substance, e.g. Cd for cadmium Pb stands for lead and Hg for mercury. You can obtain further information about the Battery Regulations from the Federal Ministry of Environment, Nature Conservation and Reactor Safety. All rights, also for translation, reprinting and copy of this manual or parts are reserved. Reproduction of all kinds photocopy, microfilm or other only by written permission of the publisher. Technical changings which are in the interest of progress reserved. We herewith confirm, that the units are calibrated by the factory according to the specifications as per the technical specifications. We recommend to calibrate the unit again, after Peak Tech Pruf und Messtechnik GmbH Gerstenstieg 4 DE-22926 Ahrensburg / Germany +49-(0) 4102-97398 80 +49-(0) 4102-97398 99 info@peaktech.de www.peaktech.de