AUDIOVOX TRY-32 3-Way Stereo Speaker System Installation Guide

June 13, 2024
AUDIOVOX

AUDIOVOX-logo

AUDIOVOX TRY-32 3-Way Stereo Speaker System

AUDIOVOX-TRY-32-3-Way-Stereo-Speaker-System-produt

SPEAKER INSTALLATION GUIDE FOR ALL REAR DECK UNIVERSAL MOUNTING x 9″, 5″ x r, x 10″ SPEAKERS

TIPS ON STEREO SPEAKER SYSTEMS

Before beginning your installation, consider the following tips on speaker placement and obtaining the best sound:

  • TIP 1: Direction of Sound
    • Always aim the speakers at the listener.
    • Avoid directing speakers toward the car floor, with the exception of rear speakers behind the rear seat. Their placement combined with the wide dispersion of bass sounds allows them to perform exceptionally well.
    • High sounds can be absorbed by the roof, so be cautious of their placement.
  • TIP 2: Sound Directionality
    • High and mid-frequency sounds are very directional, especially as frequency increases.
    • Tweeters or mid-range speakers aimed at the floor or roof will mainly be heard in that direction.
    • It’s essential to install tweeters and mid-range speakers aimed toward the passenger area and placed as high as possible. Avoid installing tweeters on the floor of the car.
  • TIP 3: Mounting Panels
    • Choose solid mounting panels for your speakers.
    • Avoid hollow, plastic, or loose panels, especially when installing powerful woofers.
    • Securely mount your speakers using all available mounting holes.
  • TIP 4: Speaker Breathing Room
    • Speakers need “breathing” room to function efficiently.
    • Ensure the speaker isn’t restricted by being placed in too small of a space or having a too-small mounting hole.
    • Conversely, the enclosure or panel they’re mounted on should be somewhat sealed. For instance, avoid cutting extra holes when mounting speakers in door panels.
  • TIP 5: Tweeter Placement
    • Tweeters can be placed in locations where other speakers might not fit.
    • They don’t need as much breathing room or reinforced mounting panels. They just require directional placement, as mentioned in TIP 2.
  • TIP 6: Avoid Physical Contact
    • Ensure no part of the speaker (except the mounting flange) touches any part of the car. Unwanted noises can occur when there’s contact.
  • TIP 7: Quality of Speaker Wiring
    • Don’t compromise on the quality of speaker wiring.
    • All Audiovox speakers come with wiring designed to handle their normal power load.

INSTALLATION

  • Ease of Installation: Car manufacturers typically provide pre-cut openings in vehicles for speaker installations. Cars can have either two or four such openings. When only two are provided, they are usually found in the rear deck and the front dash. If there are four openings, they typically consist of two in the rear deck and two in either the doors or the dash. These predetermined speaker locations are designed to simplify the installation process and to fit within the design constraints of the vehicle. However, they may not always be the best choices for achieving optimal sound reproduction.
  • Using Factory Openings: The primary advantage of using factory openings is that you avoid the need to cut into sheet metal, as the necessary holes are already pre-punched. Instead, installers would only need to cut away thin materials like plastic or fiber panels that cover these openings. It’s generally advised to steer clear of openings situated near the floor. By taking the extra step to remove door upholstery, you might uncover additional speaker location options higher up on the door. However, a word of caution: some installers, even seasoned ones, have mistakenly placed speakers in areas where they interfere with other moving components, such as window mechanisms.
  • Being Innovative: For those with a knack for mechanics and a willingness to get their hands a bit dirty, consider going beyond the obvious. Delve deep into your vehicle’s structure. By removing parts like door panels, dashes, and side panels, you open up a world of possibilities. This exploration can lead you to discover numerous hidden potential speaker locations. Some of these might surprise you with their sound quality potential.
  • You Don’t Want TO Cut Holes: Consider the add-on or surface mount type of speakers. Just pick a reasonably flat panel. drill a few holes, and fasten a few screws. and you’re listening to stereo.

CUTTING SPEAKER OPENING

Note: The procedures described here can also be used to install speakers on any reasonably flat surface.

Most cars come with factory pre-cut openings in the rear deck, commonly referred to as the package shelf. To inspect these, access the underside of this panel using the trunk. Depending on the car’s make, you’ll find at least one (but usually two) oval-shaped holes in the steel underliner of the rear deck. The size of these holes can vary, but common openings are designed for 6″ x 9″ speakers, 4″ x 10″, 4″ x 6″, and occasionally a 5″ or 5.25″ round hole.

Before installation, it’s wise to compare the speakers you’ve purchased against the existing holes in the steel sub-liner. Do this by placing the speaker against the bottom of the opening to ensure the speaker’s shape matches the cut-out. Also, verify that the speaker’s four mounting holes align with the existing holes in the steel.

AUDIOVOX-TRY-32-3-Way-Stereo-Speaker-System-1

Cutting Speaker Opening

  • Existing Opening in Steel Sub-Liner : Before making any cuts, verify the current openings in the steel sub-liner.
  • Area for Cut-Out : Determine the area you’ll need to modify or cut to fit the new speaker properly.
  • Rear Package Shelf (Viewed from Inside the Trunk) : When you’re looking at the rear package shelf from inside the trunk, this is your reference point for making adjustments.
  • Mark Four Sides for Secure Mounting : Ensure you mark all four sides accurately to allow for stable speaker mounting.

CUTTING DETAIL

Ensure all holes align. After confirming, remove the speaker and begin to cut out the oval opening in the fiber panel covering the existing hole in the steel sub-liner. Using a sharp serrated steak knife with a sawing motion can make the cutting process easier. Periodically check the speaker grille to ensure you don’t over-cut the opening.

After making the speaker openings, create the four-speaker mounting holes and widen them to a 1/16″ diameter.

NOTE: This procedure is also applicable for flat panel installations (e.g., in wagons, vans, etc.) where there’s ample space behind the panel to recess the speaker. Ensure the panel is either removable or accessible from the rear.

AUDIOVOX-TRY-32-3-Way-Stereo-Speaker-System-2

Cutting Detail

  1. Pierce Four Holes : Ensure you create the holes specifically for grille mounting.
  2. Rear Seat : Consider the location and positioning near or around the rear seat.
  3. Follow Steel Sub-liner Opening : Use the existing opening in the steel sub-liner as a guide.
  4. Use a Serrated Steak Knife : For precision, cut at a slight angle.
  5. Avoid Over-cutting : Ensure the opening isn’t larger than the speaker or its grille.

GRILLE INSTALLATION

The grille, which comes included with the speaker, has threaded rods projecting from its back. Each section of the grille has four holes in it. Firmly fit the rods into these holes. The threaded rods also have four holes that can be used with the provided screws.

Place the grille on the shelf, allowing the studs to pass through the holes you previously made. Set the speaker below the shelf and align it over the four studs of the grille. Secure it using the four provided hex nuts. If your grille requires screws instead of the provided hex nuts, insert the screws from the top of the deck through the grille and speaker, then secure them with the nuts.

Once the grille is in place, check the entire assembly for stability. Finally, wire the speakers following the specific instructions for your model.

AUDIOVOX-TRY-32-3-Way-Stereo-Speaker-System-3

  • Threaded Rod Type Grille Installation
    • Threaded Rods
    • Rear Package Shelf
    • Speaker
    • Hex Nuts
  • Studded Grille Installation
    • Studded
    • Rear Package Shelf
    • Speaker
    • Hex Nuts
  • Screw-in Grille Installation
    • Screws
    • Rear Package Shelf
    • Speakers
    • Hex nuts

01998 Audiovox Corp.
Printed in China

AUDIOVOX CORP.
150 Marcus Blvd., Hauppauge, N.Y. 11788

FAQs

How does the 4-8 ohm compatibility affect the speaker's performance?

This range indicates that the speaker can work efficiently with amplifiers rated between 4 to 8 ohms. This offers flexibility in choosing or pairing with different amplifiers.

What type of music genres or audio types does the TRY-32 best support?

As a 3-way stereo speaker system, the TRY-32 is versatile and can support a wide range of music genres, from bass-heavy tracks to classical music, providing a balanced sound profile.

How does the crossover function in this speaker system?

The crossover in the TRY-32 helps distribute different frequencies to appropriate drivers, ensuring that lows go to the woofer, mids to the mid- range driver, and highs to the tweeter for optimum sound quality.

Can the AUDIOVOX TRY-32 be used in a car audio setup?

While the TRY-32 is versatile, its specifications and flush mount design suggest it could be suitable for car audio installations. Always check with a professional for best installation practices.

What type of enclosure is recommended for this speaker?

The provided information does not specify a particular type of enclosure. However, it's always good to consult with the manufacturer or use the speaker in the recommended settings for optimal performance.

Are these speakers sold individually or in pairs?

The information provided does not specify, but often car audio speakers are sold in pairs. It would be best to check the product listing or with the retailer.

What kind of radio functionality does the speaker offer?

The details mention a 'Radio' special feature, but specific functionality isn't provided. It might refer to the speaker's compatibility with radio systems or enhanced performance for radio frequencies.

Are there any warranty or after-sales services provided with the purchase of the TRY-32?

Warranty details are not provided in the given data, but Audiovox may offer warranties on their products. It's recommended to check with the retailer or the manufacturer directly.

Is any installation hardware or wiring included with the speaker?

The provided information doesn't mention any included accessories. Typically, some speakers come with basic mounting hardware, but it's advisable to verify the product's contents.

Is the speaker compatible with different ohm ratings?

Yes, the speaker is compatible with 4-8 ohms.

What are the dimensions and weight of the packaged product?

The package dimensions are 17 x 16 x 7 inches and it weighs 6 pounds.

Is the speaker suitable for any specific applications or environments?

While the speaker is versatile, its features like flush mounting and radio functionality might make it suitable for various indoor settings. Always check the manufacturer's guidelines for specific installation recommendations.

Where can I purchase the AUDIOVOX TRY-32 3-Way Stereo Speaker System?

While not provided in the details, you can typically purchase Audiovox products from electronics retailers, authorized dealers, or online marketplaces.

Download This PDF Link:AUDIOVOX TRY-32 3-Way Stereo Speaker System

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals