AUDIOVOX CORPORATION FR-560FM Two Way Family Radio with Built In Broadcast FM Receiver Owner’s Manual

June 17, 2024
AUDIOVOX CORPORATION

AUDIOVOX CORPORATION FR-560FM Two Way Family Radio with Built In

Broadcast FM Receiver

AUDIOVOX CORPORATION FR 560FM Two Way Family Radio with Built In Broadcast
FM Receiver 

Owner’s Manual
Model FR-560FM
Two Way Family Radio With
Built-In Broadcast FM Receiver
Customer Service
1-800-290-6650

CONGRATULATIONS ON YOUR SELECTION OF THE FR-560FM
Itis one of the most sophisticated and reliable two way family radios available.
BEFORE OPERATING YOUR FR-560FM READ THIS MANUAL CAREFULLY
For Customer Service Visit Our Website At www.audiovox.com
Product Information, Photos,
FAQ’s, Owner’s Manuals

FEATURES

Your FR-560FM Family Radio with a built-in broadcast FM receiver is a portable, easy to use, two-way radio that you can carry almost anywhere. ltis skillfully constructed to give you reliable communications for many different applications. The FR-560FM is ideal for use around the house, in your boat, on hunting and camping trips, on the ski slopes or at the mall.

AUDIOVOX CORPORATION FR 560FM Two Way Family Radio with Built In Broadcast
FM Receiver  - Fig

PERFORMANCE

Your transceiver will achieve its maximum operating range when communicating with other transceivers in a flat open area with no trees or buildings obstructing its signal. Range may be up to two miles under such conditions. Obstacles such as buildings, trees or mountains will tend to reduce the transceiver’s effective range.

FCC WARNING

Replacement or substitution of transistors, diodes or other parts of a unique nature, with parts other than those recommended by the manufacturer, may cause a violation of the technical regulations of Part 15 of FCC Rules.
SAFETY INFORMATION
Your wireless handheld portable transceiver contains a low power transmitter. When the PTT button is pushed it sends out radio frequency (RF)signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for hand-held wireless devices.
Important: To maintain compliance with the FCC’ s RF exposure guidelines hold the transmitter at least 1 inch (2.5 centimeters) from your face and speak in a normal voice, with the antenna pointed up and away.
If you wear the handset on your body while using the headset accessory, use only the Audiovox supplied belt clip for this product and ensure that the antenna is at least 1 inch (2.5 centimeters) from your body when transmitting. Use only the supplied antenna. Unauthorized antennas, modifications, or attachments could damage the transmitter and may violate FCC regulations.
Normal Position: Hold the transmitter approximately 1” from your face and speak in a normal voice, with the antenna pointed up and away.

FUNCTION AND LOCATION OF THE CONTROLS

AUDIOVOX CORPORATION FR 560FM Two Way Family Radio with Built In Broadcast
FM Receiver  - CONTROLS

  1. Power Button (PWR): Press and hold this button for 2 seconds to turn the transceiver on or off.
  2. Push-to-Talk Button (PTT): Press to transmit. Release to receive.
  3. Monitor Button (M): Press and hold to bypass the squelch and listen to channel activity.
  4. Belt Clip
  5. Battery Compartment
  6. Speaker
  7. Microphone
  8. Call Button: Press and hold this button to send a ringing sound to other radios tuned to the same channel.
  9. Down Button ( ): Press this button to decrease the volume or channel setting.
  10. Up Button ( ): Press this button to increase the volume or channel setting.
  11. LCD Display: Displays the current FRS channel number as well as other functions.
  12. Function Select Button (F): Press this button to toggle through and select unit functions.
  13. Antenna: Place in the up position for transceiver use, down position for storage.
  14. Microphone / Charger Jack (MIC/CHG): For use with an external microphone and optional battery charger.
  15. Speaker (SP.) Jack: For use with an Audiovox approved headset accessory only.

LCD DISPLAY AND OPERATION

AUDIOVOX CORPORATION FR 560FM Two Way Family Radio with Built In Broadcast
FM Receiver  - LCD DISPLAY

The FR-560FM is equipped with an LCD display to indicate its settings and functions. When the radio is on, pressing any button will illuminate the display for 5 seconds.

| Transmission Indicator
---|---
| Call Button Indicator
| Low Battery Alert Indicator
| Battery Saver Mode Indicator
| Beep tone Indicator
| FRS channel Indicator (1-14).
| Preset FM memory number.
| Busy Channel Indicator. Appears on display when unitis receiving a signal.
| SCAN Indicator appears during channel scan
| FM Mode Indicator
| Key Lock Indicator
| VOX Function Indicator
| Volume Level Indicator
| Dual Watch Indicator

BATTERY INSTALLATION

Your FR-560FM requires three “AAA” alkaline cells or three rechargeable “AAA” cells. Alkaline 3 batteries will provide the best performance from your b transceiver. Remove the battery cover by rotating the belt clip away from the battery compartment. :
Slide the battery cover downward while applying pressure at the its grooved section. Observe the polarity symbols inside the battery tray when installing the batteries.
CAUTION:

  1. Incorrect battery installation can damage the unit.
  2. The microphone / charger jack is intended for use with Audiovox approved charging accessories only. Refer to the documentation included with the battery charger.
  3. Never attempt to charge alkaline batteries with the optional battery charger.

BATTERY SAVER MODE

Your FR-560FM has a unique circuit designed to dramatically extend the life of its batteries. After 10 seconds of inactivity, the FR-560FM will switch to battery saver mode. While in battery saver mode, the battery saver mode indicator ( ) is present on the display, and the transceiver will remain ready to receive any incoming transmissions while the battery saver mode is active. Pressing any of the buttons, except the up, down or power buttons, will exit the battery saver mode and illuminate the display.

USING YOUR FR-560FM

Turning the Transceiver On and Off (PWR)
Pressing the PWR button (1) for 2 seconds will activate the unit. The speaker will sound a beep tone to confirm the transceiver’s activation.
In addition, the transceiver will perform a 1-second power-on self-test, whereby the LCD display will show all functional items. To turn the unit off, simply press and hold the PWR button for 2 seconds; then release it.
Volume Level
Audio reception volume is controlled by the Up ( ) and the Down ( ) button. Momentarily pressing either button will raise or lower the volume level. A bar graph on the right side of the display will show the volume level setting.
Call Button (8)
When the CALL button is pressed, the FR-560FM will transmit a 3-second ringing sound to other transceiver’s tuned to the same channel. This feature can be used to signal other parties that voice communication is desired.
Low Battery Alert
When the batteries are in need of replacement or charging, the low battery icon Will appear on the LCD display.
Monitor Button (M)
‘You can monitor channel activity by pressing the Monitor (M) button (3). If pressed for more than 2 seconds, the monitor feature will be locked “on” to continuously monitor channel activity. Momentarily press the Monitor button again to return to normal operation.

FUNCTIONS

Function Select (F) Button
Pressing the Function button will allow selection of frequency channels, as well as selection of the various unit functions. Each press permits selection of the desired channel (1-14), FM mode on or off, beep tone, scan, VOX and Dual Watch functions. Pressing the Func- tion button in the FM mode will allow FM frequency and FM preset se- lection. This button also activates the Key lock feature when pressed and held for more than 2 seconds.
FM Frequency and Preset Memory Selection
The transceiver is capable of receiving radio signals in the FM band, and is also equipped with nine preset FM memory locations. The presets allow the user to choose the nine most-used FM stations and store them for quick access.
To enter the FM mode, press the function repeatedly until the FM icon blinks. Press the Up ( ) button and the FM icon becomes steady. The transceiver will receive the FM frequency displayed.
To select an FM frequency while in the FM mode, press the function button. The FM radio frequency icon will start to blink. Press the Up ( )or Down ( ) buttons until desired frequency is reached. Once the desired frequency is reached, press the PTT button once or the Function ( ) select button twice.
To exit the FM mode, press the Monitor (M) button and the trans- ceiver returns to the FRS mode.To recall a preset FM frequency while in the FM mode, press the Function ( ) button repeatedly until MEM display appears. Using the Up ( ) or Down ( ) buttons, select the desired memory preset (1 thru9).
To store an FM station press the function button until FM display flashes. Press Up ( ) or Down ( v ) buttons to select desired FM station. Then press function (F) button until MEM display flashes.
Using Up ( ) or Down ( ) buttons, select desired memory position (1-9) for selected station frequency. Press and hold CALL button to lock station frequency into selected memory position.
FM Auto Scan
To automatically search for an FM station, press and hold the Up ( ) or Down ( v ) button while the FM radio frequency display is blinking. When a strong FM frequency is encountered, scanning will stop and the FM display will blink. Once the desired frequency is reached, press the PTT button once or the Function ( F ) select button twice. This feature is useful in areas where reception of usual FM stations is poor, and local information is needed.
Beep Confirmation Tones
Whenever the Up/Down or Function (F) select button is pressed, the speaker will sound a beep tone to confirm each press, provided the key tone feature is enabled. The unit will also transmit a beep tone sequence after each transmission to signal the receiving party that transmission has ended. This tone is called a “Roger Beep”. To disable the key tones and “Roger Beep”, press Function button until the Beep Tone icon flashes. Then press Up ( ) or Down (v ) buttons until the icon disappears. No beep tones should be heard. To enable the key tones and “Roger Beep”, proceed as before, until the Beep Tone icon flashes. Then press Up ( ) or Down ( ) button. The key tone icon will remain displayed and a beep tone will be heard.
Channel Scanning
Press function button repeatedly until the SCAN icon flashes. Press the Up ( ) or Down ( ) button to enable the Scan function (the icon will appear steadily on the display). While in the Scan mode, the unit will pause on any active channel for 5 seconds, and then proceed to the next higher channel. The unit will scan channels 1-14 for activity and scanning will continue until the PTT button is pressed.
VOX Function
This feature enables you to have hands-free conversation. When using the external microphone or headset, your voice signal is detected and is automatically transmitted by the radio. The reply audio is received by the radio and is transferred to the headset.
To access the VOX function, press function (F) button repeatedly until VOX icon (O) flashes. Press Up ( ) or Down ( ) button to enable VOX function (icon will appear steadily).
Dual Watch Mode
This feature allows monitoring of two channels simultaneously. To activate, press function (F) button repeatedly until the Dual Watch icon (p) flashes in the display. Using the Up ( ) or Down ( ) buttons, choose the alternate channel number you wish to monitor for activity. Press the function (F) button to enter your selection. The channel display will now flash showing your current channel and alternate channel selection. To disable Dual Watch mode, press the function button until the Dual Watch icon flashes in the display. Then using the Up ( ) or Down ( ) buttons, select “0” as the channel number.
When in Dual Watch mode, the unit will transmit on the channel on which it last received a signal. To transmit on the other channel you must exit the Dual Watch mode and select the desired channel.
Key Lock
This feature prevents accidental change of unit settings. While enabled, Key Lock allows only the PTT button to operate.
To enable Key Lock, press the Function (F) button for more than 3 seconds until Key Lock icon ( ) appears. To disable the Key Lock function, press the function button for more than 3 seconds until Key Lock icon disappears.
To Transmit

  1. Set the desired primary channel.
  2. Press and hold the PTT (Push-to-Talk) button while speaking slowly and clearly in a normal voice, approximately 2 to 3 inches from the microphone.
  3. The transmit indicator ( ) will illuminate while transmitting.
  4. Release the PTT (Push-to-Talk) button when you finish speaking to receive incoming signals.

To Receive.

  1. Set the desired channel.
  2. Adjust the volume control to the desired listening volume by using the up and down buttons.
  3. The transceiver will play strong received signals through its internal speaker or through a headset, if so equipped.

Monitor Function
The Monitor (M) button can be used to play all signals present on achannel. This is useful when communicating with other parties atextremerange. The monitor function can be locked on by pressing the Monitor (M) button for three seconds. When the monitor lock has been activated, the LCD display will indicate BUSY. Pressing the monitor button a second time will unlock the monitor function.

WARNING

  • Remove the batteries from the transceiver if it is not expected to be used for long periods. This will eliminate the possibility of battery acid leaking from the batteries and corroding the transceiver.
  • Avoid exposing the unit to water or extremes of temperature.
  • Do not use this device in or near a mining facility, which uses remotely triggered explosives or in areas labeled “Blasting Area”.
  • Premature or accidental detonation may result.
  • Do not attempt to modify orin any way increase the output of this transceiver. Its output is designed to meet the legal limits set by the FCC.
  • Do not use this device or change its batteries in potentially explosive atmospheres as sparks in such areas could result in an explosion.
  • Turn your transceiver off wherever posted notices restrict the use of radios or cellular telephones. Facilities such as hospitals may use equipment that is sensitive to RF energy.
  • Turn your transceiver off on-board aircraft when requested to do so.
  • Do not place your transceiver in front of a vehicle’s air-bag. If the air-bag deploys, it could propel the transceiver like a projectile.
  • This transceiver complies with F.C.C. regulations for use in the United States. Use in other countries may be prohibited or restricted by local regulation. Please check with the local regulating agency before using this device outside of the United States.

SPECIFICATIONS*

Channels: 14
Output Power: 500 mW ERP
Battery Life Alkaline: 30-35Hours
Power Source: 4.5V DC
  • These specifications are subject to change without notice.
    They represent typical values, individual units may vary.
    Channel Frequencies:
Channel MHz
1 462.5625
2 462.5875
3 462.6125
4 462.6375
5 462.6625
6 462.6875
7 462.7125
8 467.5625
9 467.5875
10 467.6125
11 467.6375
12 467.6625
13 467.6875
14 467.7125

90 DAY LIMITED WARRANTY

Applies to Audiovox Family Radio Service Products.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company’s option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the warranty center at the address shown below.
The Company disclaims liability for communications range of this product.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY’S LIABILITY UNDER THISWARRANTY IS LIMITED TOTHE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FORANY CONSEQUENTIAL ORINCIDENTAL DAMAGES FORBREACH OF THISORANY OTHERWARRANTY,EXPRESSORIMPLIED, WHATSOEVER.
No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 1-800-290-6650 1285029 )

© 2000 Audiovox Corporation, 150 Marcus Blvd., Hauppauge,
NY 11788 128-5828C

Documents / Resources

| AUDIOVOX CORPORATION FR-560FM Two Way Family Radio with Built In Broadcast FM Receiver [pdf] Owner's Manual
FR-560FM Two Way Family Radio with Built In Broadcast FM Receiver, FR-560FM, Two Way Family Radio with Built In Broadcast FM Receiver, Built In Broadcast FM Receiver, Broadcast FM Receiver, FM Receiver, Receiver
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals