PYPES PERFORMANCE EXHAUST STT10R Cat Back Exhaust System Instructions

June 13, 2024
PYPES PERFORMANCE EXHAUST

PYPES - logo STT10R Cat Back Exhaust System
Instructions

STT10R Cat Back Exhaust System

STOP READ THIS WARNING!
Make sure you test fit these exhaust components BEFORE any cutting, welding or unnecessary bending is done. Once modified, the components of the system are NOT RETURNABLE. If you are unsure of the proper installation procedures or fitment, please contact a qualified exhaust shop or call our tech lines toll free at 800-421-3890 or visit our in- stallation gallery at: www.pypesexhaust.com/install One of our experienced exhaust techs will be glad to assist you in any way. Thanks and enjoy you new… Pypes Performance Exhaust!
SCROLL DOWN FOR INSTRUCTIONS
STT10R I STT1ORB I STT10S I STT1OSB I STT1OV I STT1OVB
2014-2020 Toyota Tundra 4.6L & 5.7L Stainless Steel Cat-back System 4.6L & 5.7L
Thanks again for purchasing your new stainless steel Pipes Performance Exhaust. Please take the time now to review these installation instructions and confirm that all the components in the kit were received in your shipment before you begin dis-assembly. If you find a component missing or have questions about the installation please contact our technical department at tech@pypesexhaust.com or through our live chat room found on the home page of the Pipes website at www.pypesex- haust.com. BILL OF MATERIALS

2 HVC21 2.5” Band Clamp
4 HVC23 3” Band Clamp
1 HVH19S Universal 3” Hanger
1 MTT10-1 Long Mindwipe w/Flange
1 MTT10-2 Short Mindwipe w/Flange
1 YTT10 Y-pipe
1 MUFF 3” Muffler Offset/ Offset
1 TTT10 3” Over Axle Tailpipe
1 TFT26-1 3” Short Tailpipe
1 YFT29 3” Y-pipe
2 EVT57 Tip
  1. Place the vehicle on a lift or four jack stands. To help your installation, pre-fit the components into a complete system on your garage floor using the picture as a reference.

  2. To remove the factory system, unbolt the clamp attaching the tailpipe to the muffler followed by unbolting the midpipes at the two flanges before the muffler.
    Note: Do not discard or damage the factory fasteners, gaskets and rubber insulators because they will be reused.

  3. Begin installing your new Pypes system by loosely bolting the new midpipes with flanges to the factory manifold downpipes using the factory copper seals and bolts followed by the YTT10 Y-pipe.

  4. The muffler is next. Use the HVH19S hanger clamp on the back of the muffler and the factory rubber isolator closest to the center of the truck. Follow that by the TTT10 tailpipe inserting the hanger on the pipe in the factory rubber isolator near the spare tire and then into the muffler. Lastly, install the short 3″ tailpipe, YFT39 Y-pipe and tips.

  5. With all the components loosely installed, adjust the system for overall aesthetics and clearance. Once the final position has been chosen, evenly tighten all fasteners from front to rear. The supplied band clamps must be very tight to properly hold the alignment of the pipes and prevent leaks. Air tools are recommend-ed for this step but if you do not have access to them, torque all clamps to a minimum of 40ft-lbs.

  6. Recheck all clamps and connections within the first 100 miles of driving.

Note: Toyota used high temp RTV sealant to seal the two mid-pipe flanges. If a leak develops here it’s acceptable to add RTV sealant to this area.
Now it’s time to fire up your truck and enjoy your new Pypes Performance Exhaust

Pypes Perform ance Exhaust
2705 Clemens Rd B103 Hatfield, PA 19440
www.pypesexhaust.com
800-421-3890

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals