OLIGHT BS100 Smart Tail Light User Manual

OLIGHT BS100 Smart Tail Light

Product Information

The BS100 is a smart tail light that provides sufficient brightness for both daytime and nighttime riding. It comes with various modes and features such as an acceleration sensor, vibration sensing function, and a memory function. The tail light is compact in size and lightweight, making it easy to install on your bike.

In the Box:

• BS100 Tail Light
• Saddle Mount
• Type-C Cable
• Seat Post Mount

Specifications:

• HIGH: 75 lumens, 100% brightness, 20 minutes runtime
• LOW: 20 lumens, 40% brightness, 20 minutes runtime
• FLASH: 0/75 lumens
• GROUP RIDE(ECO): 0/10 lumens
• SMART(DAY): 0/100 lumens
• SMART(NIGHT): 20/75 lumens
• Dimensions: (L)37(W)37(H)30mm or (L)1.46(H)1.46(D)1.18in
• Standard Charging Time: Approx. 40 minutes (5V 1A)
• Battery Capacity: 480mAh/3.6V(1.72Wh)
• Water Resistance: IPX6
• Weight: 48g / 1.69oz

How to Install:
Scheme 1:

1. Step 1
2. Step 2
3. Step 3

Scheme 2:

1. Step 1
2. Step 2

How to Recharge:
The tail light has a charging indicator that turns red when charging and blue when charging is completed. Use the provided Type-C cable to connect the tail light to a power source. The standard charging time is approximately 40 minutes.

Operation Instructions:

1. ON/OFF: Press and hold the button to turn the light on/off. The default output is the last mode used.
2. MODE SWITCHING: When the light is on, press the button to cycle through the modes: LOW-HIGH-FLASH-GROUP RIDE(ECO)-SMART.
3. ACTIVATE THE ACCELERATION SENSOR: When the light is off, press and hold the button for 5 seconds until it lights up constantly at maximum output. With the acceleration sensor enabled, the tail light becomes brighter with maximum output when braking is detected.
4. DEACTIVATE THE ACCELERATION SENSOR: When the light is off, press and hold the button for 5 seconds until it keeps flashing at maximum output.
5. VIBRATION SENSING FUNCTION: With the acceleration sensor enabled, the tail light enters sleep mode after 5 minutes of inactivity and will be automatically activated under any vibration.
6. MEMORY FUNCTION: When the light is turned on again, it will automatically switch to the last selected lighting mode.
7. LOW POWER MODE: The outer ring is always on, and the inner ring goes out when the battery is low. After approximately 5 minutes, the two rings flash. The acceleration sensor is disabled in this safe mode.

IN THE BOX

SPECIFICATIONS

The tests are performed indoors under a room temperature of 25 degrees Celsius with 25KM/H wind conditions.

HOW TO INSTALL

HOW TO RECHARGE

DANGER

• DO NOT shine the light directly into human  eyes. This may cause temporary blindness, or permanent damage to the eyes.
• DO NOT cover the light head when the bicycle light is on, or place the bicycle light head on the ground. The radiation energy of the bicycle light may cause damage to the bicycle light itself, or even result in burning to flammable objects.

WARNING

• Keep out of reach of children.
• The light contains a polymer battery. Certain restrictions may apply to this product when traveling, especially when traveling by air. Always check with your carrier for specific restrictions prior to traveling with this product.

NOTICE

• Store the light at room temperature in a dry place. Avoid moisture, or extreme hot or cold.
• Store the light in the charged condition. Avoid “deep discharge”. Battery life will decrease if the light is stored in a fully discharged condition.
• Over time, the run time of the battery will diminish. Expect about 500 full charges, depending on care. After a full life, the battery will continue to charge but with a lower run time.

OPERATION INSTRUCTIONS

ON/OFF: Press and hold the button to turn the light on/off. The default output is the last mode when turned off.
MODESWITCHING: When the light is on, press the button to cycle through
LOW-HIGH-FLASH-GROUP RIDE (ECO)-SMART mode.
ACTIVATE THE ACCELERATION SENSOR: When the light is off, press and hold the button for 5 seconds until it lights up constantly at maximum output. With the acceleration sensor enabled, the taillight turns brighter with maximum output when braking is detected.
DEACTIVATE THE ACCELERATION SENSOR: When the light is off, press and hold the button for 5 seconds until it keeps flashing at maximum output.
VIBRATION SENSING FUNCTION: With the acceleration sensor enabled, the taillight enters sleep mode after 5 minutes of inactivity and will be automatically activated under any vibration.
MEMORY FUNCTION: When the light is turned on again, it will turn to the last selected lighting mode automatically.
LOW POWER MODE: The outer ring is always on and the inner ring goes out when the battery is low, then the two rings flash after about 5 minutes. The acceleration sensor is disabled in this safe mode.

WARRANTY

Within 30 days of purchase: Return to the original seller for repair or replacement.
Within 2 years of purchase: Return to Olight for repair or replacement.
This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an Authorized retailer or Olight itself.
USA Customer Support
cs@olightstore.com

Global Customer Support
contact@olightworld.com
Visit www.olightworld.com to see our complete product line of portable illumination tools.
Dongguan Olight E-Commerce Technology Co., Ltd
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.
Made in China

References

• Olight | Illuminate Your World.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>