JBC PHN-SA Support For PCBs Up To 11 x 7 cm / 4 x 3 Instruction Manual
- June 13, 2024
- JBC
Table of Contents
www.jbctools.com
INSTRUCTION MANUAL
PHNS
Support for PCBs
up to 11x7cm/4×3”
This manual corresponds to the following reference:
PHN-SA
Packing List
The following items are included:
PHNS Support…………………………………………………………………………………………………………………………. 1 unit
Allen Key ……………………………………………. 1 unit
Ref. 0013754
Manual ………………………………………………. 1 unit
Ref. 0026993
Features and Connections
Height Adjustment
The support allows adjustment for 3 heights between the PCB and the Heating Area of the Preheater Unit.
To change the height to the highest level, proceed as follows:
-
Remove the 4 clamp knobs and the 4 black rubber caps.
-
After removing both guides, turn 180° the guide supports.
-
Place the guides and the rubber cups and adjust the sliding clamp knobs again.
Fast PCB Replacement
Moove the spring guide backward to change PCBs of the same batch fast and easily.
Removing the PCB
Loosen the spring guide (1), push the PCB against the spring guide (2) and
lift it out (3).
Placing another PCB
Position the new PCB (4) and tighten the spring guide knobs (5).
Reworking large PCBs
PCBs larger than the support can be placed onto the 4 rubber caps
Maintenance
Before carrying out maintenance or storage, always allow the support to cool down.
-
Check periodically that the Support is clean, especially the axes of the sliding guide.
-
Use a damp cloth when cleaning.
Alcohol can only be used to clean the metal parts -
Replace any defective or damaged piece.
Use original JBC spare parts only. -
Repairs should only be performed by a JBC authorized technical service.
Safety
It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
- When using the support with a preheater unit, the temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Be careful with the remains of liquid tin. In contact with the skin, it can cause burns.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the smoke produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
- This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Specifications
PHNS
Support for PCBs up to 11x7cm / 4×3”
Ref.: PHN-SA
– Support Dimensions (Low Position):
(L x W x H)
– Support Dimensions (High Position):
(L x W x H)
– Max. PCB Dimensions (Between Clamps):| 238 x 237 x 75 mm
9.4 x 9.3 x 3 in in
238 x 237 x 96 mm
9.4 x 9.3 x 3.8 in
11 x 7 cm / 4 x 3 in,
Thickness 6 mm / 0.236 in
---|---
– Total Net Weight:
– Total Package Dimensions / Weight:
(L x W x H)| 1.9 kg / 4.2 lb
280 x 280 x 164 mm / 2.4 kg
11.02 x 11.02 x 6.45 / 5.29 lb
Complies with CE standards.
ESD safe.
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage
paid, to the dealer where it was purchased.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must
be collected and returned to an authorized recycling facility.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>