SECRET LAB MAGNUS Pro Sit Stand Metal Desk Instruction Manual
- June 9, 2024
- SECRET LAB
Table of Contents
SECRET LAB MAGNUS Pro Sit Stand Metal Desk Instruction Manual
OTHER LANGUAGES
To view this manual in the following languages, please scan the QR Code to the left.
https://secretlab.co/resources-magnus-pro
READ THE ASSEMBLY GUIDE AND USER MANUAL
https://secretlab.co/resources-magnus-pro
On many occasions, problems can be the result of improper assembly. Scan the QR code or visit our website secretlab.co/ resources to reference the Assembly Guide and User Manual document to ensure the Secret lab MAGNUS Pro is assembled correctly. If problems persist after confirm ing proper assembly, reference the troubleshooting steps throughout this document.
OBTAINING REPLACEMENT PARTS
https://secretlab.co/pages/support
WARNING: Do not attempt to open the housing of Control Box, Control Panel, Leg Columns and Motors. There are no user serviceable parts in these components. Should your desk require servicing, contact our customer support for assistance. If replacement parts are required after troubleshooting the desk. scan the QR code or visit our website secretlab.co/support.
GENERAL TROUBLESHOOTING STEPS
PERFORM THE RESET PROCEDURE:
- Press and hold the V button to lower the Secretlab MAGNUS Pro to the lowest position (650mm/25.6″).
- Press and hold the V button until the digital display shows “Rest”.
- The desk will move up and down slightly. Do not release the button until a beep is heard.
- The Motorized Leg Columns are now synchronized via the software in the Control Box.
- Operate the desk to the highest (1250mm/ 49.2″) and lowest posit ion (650mm/25.6″) to confirm proper function.
POWER CYCLE THE CONTROL BOX:
- In the unlikely event that an error occurs, and the Secret lab MAGNUS Pro is unresponsive, disconnect power to the desk for at least 1 0 seconds to reset the Control Box.
- Reconnect power to the desk and perform the reset procedure to synchronize the Motorized Leg Columns.
CHECK ALL CABLE CONNECTIONS
- Check for power at the wall outlet.
- Check that all cables are securely connected.
- Check all cable connections for damage to the cord or pins.
- Perform the reset procedure.
CHECK FOR OBSTRUCTIONS
- Confirm that there is nothing obstructing your desk’s motion, clearing out anything that is too close – above, below, or beside it.
- Confirm that items mounted to the desk are free from obstruction too.
- Check that the Control Box is attached firmly to the Metal Desk Top by removing the Service Hatch on the Desk Frame.
- To adjust the anti-collision sensitivity of your Secret lab MAGNUS Pro, refer to the Advanced Anti-collision System section below.
ADVANCED ANTI-COLLISION SYSTEM
WARNING: The default anti-collision sensitivity setting has been calibrated for your safety. Adjust at your own risk.
- Press and hold the “S ” button on the Control Panel for 5 seconds to enter the advanced setting interface.
- The digital display will show “S-:”.
- Press the V button to “S- 2”. Press the “S ” button to access and edit the setting.
- Cl indicates that the ant i-collision system is turned off, B is the most sensitive setting, and : is the least sensitive setting.
- Press the A / V buttons to toggle between the settings.
- Once the desired setting is selected, press the “S ” button to save and exit the advanced setting interface.
- The selected anti-collision sensitivity setting is saved and your Secret lab MAGNUS Pro is now ready to use.
UNRESPONSIVE CONTROL PANEL:
- If the Control Panel is unresponsive, unplug the Control Panel from the Control Box for 10 seconds.
- Plug the Control Panel back in.
ERROR CODES
Secretlab, the Secretlab logo and the Tr iangle logo are registered trade
marks of Secretlab.
MAGNUS is a registered trade mark of Secretlab in Singapore. New Zealand and
the Philippines.
The MAGNUS logo is a registered trade mark of Secretlab in the EU.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>