REED 98199 Pump Stick Instructions
- June 13, 2024
- REED
Table of Contents
REED 98199 Pump Stick
Product Information
- Product Name: Motor Stabilizer / Motor Housing
- Model Numbers: 98199, 08140, 08142, 08141, 08144
- Manufacturer: Reed Manufacturing
- Manufacturer Address: 1425 West 8th Street Erie, PA 16502 USA
- Manufacturer Phone: 800-666-3691 or +1 814-452-3691
- Manufacturer Fax: +1 814-455-1697
- Manufacturer Email: reedsales@reedmfgco.com
- Manufacturer Website: www.reedmfgco.com
Purpose of these instructions is to guide you through the replacement of the Motor Housing for the REED Pump Stick®.
INSTALLATION INSTRUCTIONS
REPLACEMENT INSTRUCTIONS
- Remove the End Cap, Screen and Motor Spacer, and pull the Motor Assembly out of the Pump Housing.
- Remove the 3 flat head screws from the front of the Motor Housing and pull out the Motor Assembly. Remove the 2 wire connectors from the back of the motor.
- Unscrew the upper End Cap and remove Pump Housing.
- Cut off the 2 terminals as close to the terminals as possible.
- Remove the 2 screws on the back end of the Motor Housing and discard.
- Pull wires out of the Motor Housing and remove O-rings and O-ring Retainer from the wire and discard O-rings and Retainer.
- Feed the 2 wires through the 2 LARGER HOLES in the new Motor Stabilizer. (The two smaller holes are for the screws.) Place 2 O-rings on to each wire and push them up to slightly above their original location.
- Push the wires through the holes on back end of the new Motor Housing up to the O-rings. While holding the motor housing in position Push down on the Motor Stabilizer with a back-and-forth rotation to seat the O-rings into the counter bores on the back of the Motor Housing.
- Secure the Motor Stabilizer to the Motor Housing with the new 3/8” long screws making sure not to over tighten and strip out the holes in the motor housing.
- Strip about 3/16”-1/4” of insulation off the end of the wires and crimp on the Wire Terminals.
- Slip the Pump Housing back over the Motor Housing and thread onto the upper End Cap.
- Plug the wires onto the motor being sure the Red Wire is placed on to the terminal with the Red Dot next to it.
- Push the Motor Assembly into the Motor Housing until the O-ring contacts the housing. Rotate the Motor Assembly while pushing in to both seat the O-ring and align the screw holes. The O-ring on the Motor Assembly should have a thin layer of lubricant, if not, apply lubricant.
- Thread in all three flat head screws until just before the heads make contact with the motor mount. Advance all three screws in small increments until the motor mount is seated into the housing, being sure not to crimp the O-ring. Very lightly tighten the screws.
- Insert the Motor Assembly back into the Pump Housing.
- Test the motor rotation. Insert the battery and turn on the pump. The impeller should rotate in a counterclockwise (CCW) direction. See drawing.
- Insert the motor spacer and rotate until the 3 slots engage the flanges on the Motor Assembly. Replace the Screen and End Cap.
Parts List
CP15MHRA #98199 Motor Stabilizer / Motor Housing
Parts List
Ref. No.| Description| Item Code| Qty. Used
1| Motor Assembly| 08142| 1
2| Motor Housing| 48102| 1
3| Motor Stabilizer| 48210| 1
4| #4 x 3/8 Pan HD Screws| 48166| 2
5| O-Ring| 48117| 4
6| Wire Connector| 48115| 2
CONTACT
REED MANUFACTURING
- 1425 West 8th Street Erie, PA 16502 USA
- Phone: 800-666-3691 or +1 814-452-3691
- Fax: +1 814-455-1697
- reedsales@reedmfgco.com
- www.reedmfgco.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>