ridetech 11729122 Rear Muscle Bar Sway Bar Kit Installation Guide

June 13, 2024
ridetech

Installation
Instructions

Part # 11729122 – 2019 – 2023 Silverado 1500 Rear Sway Bar

11729122 Rear Muscle Bar Sway Bar Kit

2019-2023 Silverado Rear Sway Bar
Installation Instructions

Recommended Tools

THIS SWAY BAR IS DESIGNED TO BE USED WITH THE REAR LOWERING KIT #11729511.
Major Components …..In the box

Item # Part # Description QTY
1 90003505 Rear Sway Bar 1
2 90003517 Rear Sway Bar Frame Mount 2
3 90003283 Sway Bar Axle Bracket 2
4 70015012 Sway Bar Bushing 2
5 90001345 Sway Bar Bushing Strap 2
6 90000088 7/16”-20 U-Bolt, 3.25” Wide x 4.50” Long 2
7 PosiLink Assembly
8 90003842 10mm 90 Degree End link 4
9 90003506 PosiLink Spacer 2
10 90000225 Copper Crush Washer 4
11 99115012 M10-1.5 x 130mm Threaded Stud 2

ridetech 11729122 Rear Muscle Bar Sway Bar Kit - fig1

Hardware Kit …..# 99010220

Item # Part # Description QTY

U-BOLT
12| 99432007| 7/16”-20 Nylok Nut| 4
13| 99433005| 7/16” SAE Flat Washer| 4
END LINKS
14| 99113002| M10 Flat Washer| 8
15| 99112002| M10-1.5 Nylok Nut| 4
END LINK BRACKET TO FRAME
16| 99501004| 1/2”-13 X 2 3/4” Hex Bolt| 2
17| 99503014| 1/2” SAE Flat Washer| 4
18| 99502009| 1/2”-13 Nylok Nut| 2

Getting Started………

Note: This sway bar kit utilizes an anti-friction lining in the sway bar bushing. The lining allows the sway bar to move freely and quietly in the bushing. No lubrication is required.
THIS SWAYBAR ATTACHES TO THE AXLE AND FRAME.

  1. Jack the vehicle up to a safe working height and support with jack stands. Make sure the jack stands are stable before working under the truck.
  2.  The rear flip kit needs to be installed before the rear sway bar.
  3. Diagram 3 shows how the sway bar will be positioned on the rear differential.
  4. Open the sway bar bushing at the split and slip it OVER the sway bar at the locations shown in Image 4. Do this for both bushings.

Sway Bar Installation

  1.  Install the bushing straps over the sway bar bushings.
  2.  Image 6 shows the passenger side frame bracket installed. The frame/crossmember will need to be drilled with a 1/2” drill bit. The frame bracket is centered below the crossmember with the locating tab against the outside of the frame rail.
  3. Image 7 shows the drilled hole to help give you an idea of the position. Hold the bracket  on the bottom of the frame rail and mark thehole to be drilled. Again, the bracket needs to be centered below the crossmember with the locating tab against the outside of the frame rail.
  4.  Drill the bottom of the frame with a 1/2” drill bit.
  5.  The 1/2” hole needs to drilled through the bottom of the crossmember too.
  6. Install a 1/2” flat washer on a 1/2” – 13 x 2 3/4” bolt. Hold the frame bracket in place with the tab on the outside of the frame. Insert the bolt/washer in the aligned holes.
  7.  Install a 1/2” flat washer & 1/2”-13 nylok nut on the threads of the bolt sticking into the crossmember. Torque to 75 ft-lbs. Repeat the previous steps for the frame bracket on the other side.
  8. Install a 7/16” u-bolt on each axle tube
  9. Slip the axle mount onto the u-bolts. The “teeth” of the axle bracket will sit against the axle tube.
  10. Hold the sway bar in position on the truck with the center bend toward the ground. Slide the sway bar bushing strap onto the u-bolt.
  11. Install a 7/16” flat washer & 7/16”-20 nylok nut on the threads of the u-bolts. Center the sway bar on the axle. Snug the hardware down and verify the axle mounts are parallel with the leaf springs. Torque the u-bolt hardware to 35 ft-lbs.
  12.  Install a M10 flat washer on the threads of the PosiLink. Insert the PosiLink in the mounting hole of the frame bracket with the threads of the end link pointing to the center of the truck.
  13.  Install a M10 flat washer & M10-1.5 nylok nut on the threads of the PosiLink Torque the nut to 37 ft-lbs. Repeat on the other side.
  14. Install a M10 flat washer on the threads of the PosiLink. Insert the PosiLink in the MIDDLE mounting hole of the sway bar arm. The threads of the PosiLink should be pointing to the outside of the truck.
  15. Install a M10 flat washer & M10-1.5 nylok nut on the threads of the PosiLink Torque the nut to 37 ft-lbs. Repeat on the other side.
  16. DOUBLE CHECK THE HARDWARE TO MAKE SURE IT IS TIGHT.

Sway Bar Adjustment

ridetech 11729122 Rear Muscle Bar Sway Bar Kit -
STANDARD

This sway bar has 3 positions to aid in the tuning of your truck’s handling. We start in the #2 MIDDLE position and tune from there. The # 3 position to the rear of the truck will make the sway bar stiffer. The #1 position to the front of the truck will make the sway bar softer. The position of the sway bar linkage will be determined by several factors; spring rate, front bar size, and even tire size. Keep in mind, the handling of the truck will be affected when you change the linkage location. Drive the truck to get  accustomed to the new handling characteristics.
Rear Sway Bar Rates:
Hole 1: 150 lbs/in
Hole 2: 185 lbs/in
Hole 3: 200 lbs/in

www.ridetech.com
10/28/22
812-482-2932

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ridetech User Manuals

Related Manuals