Jandy H0669700 Infinite WaterColors LED Light Controller User Manual

Jandy H0669700 Infinite WaterColors LED Light Controller

Product Information

This product is an AquaLink RS revision Y or later and requires the following for installation: AquaLink RS revision Y or later.

Important Safety Instructions
This product should be installed, operated, and used safely to prevent property damage, personal injury, or death. It is recommended to follow these safety precautions:

Safety Instructions

• All electrical work must be performed by a licensed electrician and comply with national, state, provincial, and local codes.
• Before installation or service, always turn off the pump to release the pressure in the pump/filter system. Refer to the pump/filter owner’s manual for specific instructions.

Landscape Lighting Instructions
Specific instructions for landscape lighting are provided in Section 1.2 of the manual.

Specifications
The specifications for this product are detailed in Section 1.3 of the manual.

System Overview
The system overview is provided in Section 2 of the manual.

Package Contents
The package includes all the necessary components for installation. Refer to Section 2.1 for a detailed list.

Location Requirements for Pool and Spa Light Applications
Section 2.2 of the manual provides information on the location requirements for pool and spa light applications.

Installation
The installation process is explained in Section 3 of the manual.

Mounting
Section 3.1 provides instructions on how to mount the product.

High Voltage Wiring
Section 3.2 explains the steps for high-voltage wiring.

Low Voltage Wiring
Section 3.3 provides instructions for low-voltage wiring.

Bonding
Section 3.4 explains the bonding requirements for the product.

Product Usage Instructions

The product usage instructions are outlined in Section 4, Section 5, and Section 6 of the manual.

Light Setup
Section 4.1 and Section 5.1 provide information on how to set up the lights.

Turn Lights On/Off
Section 4.2 explains how to turn the lights on and off.

Select Colors
Section 4.3 and Section 5.2 provide instructions on how to select different colors for the lights.

Adjust Brightness
Section 4.4 explains how to adjust the brightness of the lights.

Amazon Alexa Light Control
Section 6 of the manual provides information on controlling the lights using Amazon Alexa.

Troubleshooting
If you encounter any issues with the product, refer to Section 7 of the manual for troubleshooting guidance.

FCC Regulatory Compliance Statement
The product complies with Part 15 of the FCC Rules. For more information, refer to the manual.

CAUTION : Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.

NOTE : If you experience interference, try reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, or connecting the equipment to a different circuit. Consult the dealer or a radio/TV technician for assistance.

Jandy® Infinite WaterColors™ LED Light Controller

This product requires AquaLink RS revision Y or later

WARNING:

FOR YOUR SAFETY
This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed, where such state local, or provincial requirements exist. In the event no such state or local requirement exists, the individual in charge of installation must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Improper installation and/or operation can create dangerous electrical hazards, which can cause high voltages to run through the electrical system. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Improper installation and/or operation may void the warranty.

If these instructions are not followed exactly, a fire or explosion may result, causing property damage, personal injury, or death. DO NOT MODIFY THIS EQUIPMENT!

ATTENTION INSTALLER : This manual contains important information about the installation, operation, and safe use of this product. This information should be given to the owner/operator of this equipment.

Section 1. IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

Safety Instructions
A licensed electrician must perform all electrical work and conform to all national, state, provincial, and local codes. When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:

WARNING

EQUIPMENT UNDER PRESSURE: Always turn the pump off before installation or service. Your pump/filter system is operated under pressure and the pressure must be released before you begin work. Please see your pump/filter owner’s manual for further instructions.

WARNING: To reduce the risk of electric shock, fire, or injury, service should only be attempted by a qualified pool service professional.

Risk of electric shock: When installed as a power source for landscape lighting: Install a power unit 5 feet (1.5 m) or more from a pool or spa and 10 feet (3.05 m) or more from a fountain. Where the power unit is installed within 10 feet (3.05 m) of a pool or spa connect the power unit to a GFCI- protected branch circuit. Canadian installations must be at least three (3) meters from the water.

WARNING: Risk of electric shock which can result in serious injury or death: Before attempting to install or service, ensure that all power to the circuit supplying power to the system is disconnected or turned off at the circuit breaker. All wiring must be done by the National Electrical Code® (NEC)®, NFPA-70®, including those in Article 680 – Swimming Pools, Fountains, and Similar Installations.

In Canada, the Canadian Electrical Code (CEC), CSA C22.1, must be followed. All applicable local installation codes and regulations must be followed.

ATTENTION : This power center and the chlorine generator control center are not to be considered suitable for use as service equipment. Therefore, it is required to have the appropriate means of disconnection, circuit isolation, and/or branch circuit protection installed upstream of the power/control center

WARNING: To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all times

WARNING: Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use a spa or hot tub unless they are closely supervised at all times
This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

PREVENT CHILD DROWNING

Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of your pool’s operational system. Locate the components of your operational system at least 1 m (3 ft 3 in) from the pool so children cannot use the equipment to access the pool and be injured or drown.

To reduce the risk of injury, do not remove the suction fittings of your spa or hot tub. Never operate a spa or hot tub if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the equipment assembly.

WARNING

To avoid injury ensure that you use this control system to control only packaged pool/spa heaters which have built-in operating and high limit controls to limit water temperature for pool/spa applications. This device should not be relied upon as a safety limit control. Water temperatures over 100°F (38°C) may be hazardous to your health.

WARNING

A terminal bar marked “GROUND” is provided within the power center. To reduce the risk of electrical shock, connect this terminal bar to the grounding terminal of your electric service or supply panel with a continuous copper conductor having green insulation and one that is equivalent in size to the circuit conductors supplying this equipment, but no smaller than no. 12 AWG (3.3 mm2). In addition, a second wire connector should be bonded with a no. 8 AWG (8.4 mm2) copper wire to any metal ladders, water pipes, or other metal within five (5) feet (1.52 m) of the pool/spa. In Canada, the bonding wire must be a minimum of 6 AWG (13.3 mm2).

WARNING

Install only on a branch circuit protected by a ground fault circuit interrupter (GFCI), Class A GFCI in Canada. The conductors on the load side of the ground-fault circuit-interrupter shall not occupy conduits, boxes, or enclosures containing other conductors unless the additional conductors are also protected by a ground-fault circuit-interrupter. Refer to local codes for complete details.

CAUTION : This device is intended for use with permanent swimming pools and may also be used with hot tubs and spas if so marked. Do not use with storable pools. A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity.
Modifications made to this equipment, which are not authorized by the manufacturer, may void the user’s authority to operate this equipment.

WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:

• Turn off/unplug it and allow it to cool before replacing the lamp.
• The lamp gets HOT quickly! Contact only switch/plug when turning on.
• Do not touch the hot lens, guard, or enclosure (see diagram/picture).
• Keep lamps away from materials that may burn.
• Do not touch the lamp at any time.
• Use a soft cloth. Oil from the skin may damage the lamp.
• Do not operate the luminaire fitting with a missing or damaged shield.
• The lighted lamp is HOT!

SAVE THESE INSTRUCTIONS

Landscape Lighting Instructions

THIS SECTION INCLUDES INSTRUCTIONS, PRECAUTIONS AND WARNINGS APPLICABLE TO LANDSCAPE LIGHTING APPLICATIONS. FOLLOW ALL REQUIREMENTS OF THIS SECTION WHEN A LIGHT CONTROLLER IS USED IN LANDSCAPE LIGHTING APPLICATIONS.

CAUTION : For use only on a branch circuit protected by a ground fault circuit interrupter (GFCI), Class A GFCI in Canada.

WARNING: RISK OF ELECTRICAL SHOCK

Install a power unit 5 feet (1.5 m) or more from a pool or spa and 10 feet (3.05 m) or more from a fountain. Where the power unit is installed within 10 feet (3.05 m) of a pool or spa connect the power unit to a GFCI-protected branch circuit. In Canada, do not mount power supply or landscape luminaires within 3 m (10 feet) of a swimming pool spa, or fountain.

THIS DEVICE IS ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL INSPECTION AUTHORITIES HAVING JURISDICTION

• IN CANADA, LANDSCAPE LIGHTING POWER SUPPLIES ARE FOR OUTDOOR USE ONLY. MOUNT AT LEAST 30 CM ABOVE GROUND.
• THIS DEVICE IS CERTIFIED FOR USE WITH LANDSCAPE LIGHTING SYSTEMS. THIS DEVICE IS ACCEPTED AS

A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL INSPECTION AUTHORITIES HAVING JURISDICTION.

• DO NOT CONNECT TWO OR MORE POWER SUPPLIES IN PARALLEL.
• LANDSCAPE LIGHTING SYSTEMS ARE FOR OUTDOOR USE ONLY. NOT FOR USE IN DWELLING UNITS.

Specifications

Power Supply

Input:| 120VAC, 60 Hz, 2.75A
Output:| 14 VAC, 60 Hz, max 300W
Enclosure
Type 3RX
Knockouts
10 total 1/2” – 3/4” combination

Aqualink will support control of up to 4 Infinite WaterColors Light Controllers and each controller will support communication with up to 16 lights. Ensure the combined light wattage does not exceed 240W per controller.

WARNING: The Infinite WaterColors LED Light Controller should not be considered suitable for use as service equipment. Therefore, it is required to have the appropriate means of disconnection, circuit isolation, and/or branch circuit protection installed upstream of the power center.

Section 2. System Overview

This manual provides installation and basic operational instructions for the Jandy Infinite WaterColors LED Light Controller. The Infinite WaterColors LED Light Controller includes a 300W transformer specifically designed to supply 14 volts to pool/spa lights, submersible fixtures, and outdoor garden lights. The Infinite WaterColors LED Light Controller is capable of communicating with low-voltage lights and automation systems. The built-in circuit protection will disconnect power to the transformer in case of defect or overload. These transformers are suitable for direct connection to underwater pools, spas, and landscape lights.

Read the installation and operation instructions completely before proceeding with the installation. Keep this manual in a safe place for future reference when inspecting or servicing the Infinite WaterColors LED Light Controller.

Before starting, check that you have the correct parts as indicated below. If any parts are missing or incorrect, please call your local distributor or technical support at 1-800-822-7933 for assistance.

Package Contents

Jandy Infinite WaterColors LED Light Controller

1- Enclosure and PIB
2- Upper mounting bracket
3- Lower mounting bracket
4- 20 FT RS-485 Cable

Location Requirements for Pool and Spa Light Applications
In order to protect the Infinite Water Colors LED Light Controller from pressurized water spray (such as that from irrigation sprinklers) and mechanical impacts and/or damage, it should be located:

• At least 4 inches (10 cm) above the ground.
• At least 8 inches (20 cm) above the water level.
• At least 4 feet (1.3 m) from the inside edge of the pool or spa, at least 10 feet (3 m) from a fountain, or as required by local code in the US.
• At least 10 feet (3 m) from the inside edge of the pool, spa, or fountain in Canada, or as required by local code.

Section 3. Installation

Mounting
The Infinite WaterColors LED Light Controller is shipped with mounting brackets fastened on the back.

• Turn the Light Controller over and inspect the brackets installed inverted on the back.
• If any parts are missing or damaged, please call your local distributor or technical support at 1-800-822-7933 for assistance.
  1. Remove mounting screws from the upper and lower brackets on the back of the Light Controller.
  2. Rotate and secure upper and lower brackets with mounting screws to the same mounting holes, see Figure 2.
  3. Mark the location for the mounting screws.
  4. Drill holes where the mounting screws will be installed.
  5. Secure screws (or other hardware appropriate for the mounting surface) through either the keyhole slots or the mounting holes of the Light Controller enclosure, see Figure 3.

High Voltage Wiring

WARNING: Risk of electric shock which can result in serious injury or death: Before attempting to install or service, ensure that all power to the circuit supplying power to the system is disconnected or turned off at the circuit breaker. All wiring must be done by the National Electrical Code® ( NEC(R) )®, NFPA70®.

In Canada, the Canadian Electrical Code (CEC), CSA C22.1, must be followed. All applicable local installation codes and regulations must be followed.

Wiring connections must be made exactly as shown in the wiring diagram found on the inside of the Infinite WaterColors LED Light Controller cover. The NEC and CEC also require that pool equipment be bonded together as part of the equipotential bonding grid. Zodiac Pool Systems LLC provides a labeled bonding lug on the bottom of the Light Controller to accommodate this requirement.

1. Turn off the power at the breaker panel.
2. Remove the cover. The cover is held on by one screw, see Figure 4(a).
3. Remove a knockout from the bottom left side of the Light Controller.
4. Thread a conduit connector that is rated to local code into the knockout hole on the Light Controller, see Figure 4(b).
5. Feed 120 VAC through the conduit and conduit connector on the Light Controller, see Figure 4.
6. Connect the green ground wire to the ground terminal bar in the Light Controller, see Figure 4(c).
7. Use wire nuts to connect the line wires (black to black) and neutral wires (white to white), see Figure 4(d).
8. Proceed to section 3.3 Low Voltage Wiring.

Low Voltage Wiring

1. Remove a knockout from the bottom right side of the Light Controller.

2. Thread a conduit connector into the knockout hole on the Light Controller, see Figure 5.

3. Feed low voltage light cord through the conduit and conduit connector on the Light Controller, see Figure 5.
   NOTE : It is recommended to add a junction box when installing more than two lights.

4. Use wire nuts to connect the low voltage light wires, the white wire connects to the orange, and the black wire connects to the orange wire, see Figure 5.

   • If installing a niched light, connect the green ground wire to the terminal bar in the controller

5. Once power is restored, verify lights perform the “rainbow sequence” (it could take up to two minutes), this indicates the lights are powered and communicating to the Light Controller.
   NOTE : A blinking yellow light means no communication between lights and the light controller.

6. Turn off the power at the breaker panel.

7. RS-485 comes factory-wired to the Light Controller. Connect the low-voltage RS-485 communication wires to the Aqualink RS automation system. First wire red (R) to 1, black (B) to 2, yellow (Y) to 3, and green (G) to 4 on the connector, see Figure 6.

8. Check all connection points and wiring for secure connections.
   NOTE: Cover screw ensures bonding to ground, and must be secured in place.

9. Turn on the breaker to restore power (LED2 will turn on red and LED1 will start flashing green). Pool & Spa Lights will be off due to control from automation, see Figure 7.

10. Install the cover and secure the hand tight with the screw provided.

11. Turn on the breaker to restore power (LED1 will turn on).

Bonding
Zodiac Pool Systems LLC requires that the Infinite Water Colors LED Light Controller be connected to a “bonding loop” that includes all electrical equipment in the system and on the equipment pad. Bonding lugs must be connected with a solid copper wire not smaller than 8 AWG (6 AWG in Canada). Failure to do so may void the Zodiac Pool Systems LLC warranty.

CAUTION: To prevent premature failure of the equipment resulting from stray voltages and voltage differentials, the Infinite WaterColors LED Light Controller must be bonded to other equipment that is part of the pool plumbing system with a solid copper wire not smaller in diameter than 8 AWG (6 AWG in Canada).

Additionally, in the United States the National Electrical Code® (NEC®) and in Canada the Canadian Electrical Code (CEC), require that all metallic components of a pool structure, including reinforcing steel, metal fittings, and above-ground components be bonded together (forming an equipotential bonding grid) with a solid copper conductor not smaller than an 8 AWG (6 AWG in Canada).

The NEC and CEC also require that the equipment and/or appliances associated with the pool water circulating system, including, but not limited to, pump motors and heaters, be bonded together as part of the equipotential bonding grid. Zodiac Pool Systems LLC provides special labeled bonding lugs on the bottom of the power center to accommodate this requirement.

After bonding the electronics to the grounding lug, the installer must verify the ground continuity of all metal components using a multimeter.

WARNING: The Installer must ensure that the Infinite WaterColors LED Light Controller is in acceptable working condition; including all seals/gaskets must be
in place and functional; the grounding lug must be present, functional, and bonded; and corrosion must not compromise ingress protection against weather. Additionally, all hardware must be present and functional. If any of the aforementioned conditions are not met, a new enclosure MUST be used.

WARNING: Risk of electric shock which can result in serious injury or loss of life. Before attempting to install or service, ensure that all power to the circuit supplying power to the system is disconnected or turned off at the circuit breaker. All wiring must be done by the National Electrical Code® (NEC)®, NFPA-70®.

In Canada, the Canadian Electrical Code (CEC), CSA C22.1, must be followed. All applicable local installation codes and regulations must be followed.

Wiring connections must be made exactly as shown in the wiring diagram found on the inside of the Infinite WaterColors LED Light Controller cover. The NEC and CEC also require that pool equipment be bonded together as part of the equipotential bonding grid. Zodiac Pool Systems LLC provides a labeled bonding lug on the bottom of the Light Controller to accommodate this requirement.

Section 4. iAquaLink® App Features

Download the iAquaLink app or upgrade to the latest version before light and zone setup. App function and design are subject to change.

NOTE : When replacing lights, make sure to follow these steps:

• Remove any existing light aux names (system setup > label aux >)
• Remove previous light aux labels (system setup > color lights)
• Remove schedules of light auxiliaries (system setup > schedules)

Light Setup

1. Open the app on your device.
2. From the My Systems page, select your pool.
3. From the home page, choose the cog system icon on the top right and select System Setup.

Assign Lights

1. From the System Setup page, select Light Setup and Assign Lights.
2. From the Assign Lights pop-up, choose to proceed to continue the process.
3. On the Light Zone Setup page, select a light to move it to a different zone and follow further instructions in the app.

NOTE : When exiting the Light Zone Setup page, the lights will turn off.
NOTE : Lights have to be assigned to a zone to rename the zone.

Name Light Zones

1. Go to > System Setup > Light Setup > Zone Name.
2. From the Edit Zone Name pop-up, enter the zone name and choose OK.

Turn Lights On/Off

1. Open the app on your device.
2. From My Systems page, select your pool.
3. Choose the equipment page.
4. Turn zone lights on/off by tapping the toggle to the right of the desired zone.

Select Colors

1. Open the app on your device.
2. From the My System page, select your pool.

Select Custom Color

1. Go to > equipment page.
2. From the equipment page, choose the zone you want to change color.
3. From that zones page, choose Custom Color.
4. Choose your custom color from the color wheel.
5. Choose Apply to apply the custom color to your zone.

Preset Colors

1. Go to the equipment page and select the zone you want to change color.
2. After selecting the zone, then choose from the list of preset colors to apply that preset color to your zone.

Preset Color Shows

1. Go to the equipment page and select the zone you want to change color.
2. After selecting the zone, then choose from the list of preset colors to apply that preset color to your zone.

Preset Color Shows

1. From the equipment page, choose the zone you want to change color.
2. After selecting the zone, choose from the list of preset color shows to apply that preset color show to your zone.

Adjust Brightness

1. From the equipment page, select the sun icon on the zone where you want to adjust the brightness.
2. Move the slider bar up or down with your finger and then click apply to change the brightness.

Section 5. OneTouch Setup

Light Setup
Assign Lights

1. Choose the menu on the OneTouch display screen and press select.
2. From the menu screen, go to > System Setup > IWC Lights.
3. Select zone set up.
4. From the IWC Lights Zone Setup screen, choose Assign Zone.
5. From the IWC Lights screen, choose your device (light controller) from the list to assign lights to a light zone.
6. A list of lights currently connected to the light controller will appear, select a light and assign it to a light zone (up to 4 zones).

NOTE : The list will display the last six digits of your Infinite WaterColors LED Light Controller serial number located on the bottom of your controller.

NOTE : When exiting the Light Zone Setup page, the lights will turn off

Name Light Zones

1. Choose the menu on the OneTouch display screen and press select.
2. From the menu screen, go to > System Setup > IWC Lights.
3. From the IWC Lights screen, select Zone Setup.
4. From the IWC Lights Zone Setup screen, choose Zone Name.
5. From the IWC Lights Rename screen, choose the zone you want to name and enter the name.

Select Color

1. Choose equipment on the OneTouch display screen and press select.
2. Scroll through the menu and select the desired light zone.
3. From the list of preset colors and color shows, select the desired color.

NOTE : To turn off lights, re-select the light zone and wait 5 seconds.
NOTE : Custom color can only be adjusted using the iAquaLink app.

Section 6. Amazon Alexa Light Control
Go to iaqualink.com for more information on controlling your Infinite WaterColors lights through Amazon Alexa.

Section 7. Troubleshooting

LED2 should be on.
The Light Controller is not communicating with the automation| Check that RS4-85 is connected, LED1 should be blinking.
Lights are not powered| Check that the light is wired to the Light Controller output.
Lights have failed| Replace the light or swap the PCBA

(for niched pool and spa LED lights only).

Lights are flashing yellow| Lights are powered but not communicating with the Light Controller| Check that lights are wired to the Light Controller. Other transformers are not compatible.
Lights are on, but not switching to the selected color| Non-compatible lights are connected| Check that Infinite WaterColors Lights are connected. Other lights are not compatible.
Lights are in a different zone than the

one being switched

| Ensure lights are in the zone selected.
Some of my lights come on, but not others| Lights are in separate zones| Ensure lights are in the zone selected.

FCC Regulatory Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Zodiac Pool Systems LLC 2882 Whiptail Loop # 100 Carlsbad, CA 92010, USA Jandy.com  1.800.822.7933
Zodiac Pool Systems Canada, Inc. 2-3365 Mainway Burlington, ON L7M 1A6, Canada Jandy.ca  1.800.822.7933

©2023 Zodiac Pool Systems LLC. All rights reserved. ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license. All other trademarks are the property of their respective owners.
H0669700_REVE

ETL LISTED CONFORMS TO

• ANSI/UL STD 379
• UL STD 50E
• UL STD 1838

CERTIFIED TO

• CSA C22.2 No. 218.1,
• CSA C22.2 No. 250.7,
• CSA C22.2 No. 94.2 and
• CSA C22.2 No. 89

References

• iAquaLink Pool Automation | Swimming Pool Automation & Mobile Apps by ZODIAC®
• Jandy Swimming Pool Equipment | Canada | Jandy

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>