Jandy Laminar Jet with RGBW LED light Replacement Kit Installation Guide
- June 4, 2024
- Jandy
Table of Contents
Jandy Laminar Jet with RGBW LED light Replacement Kit
WARNING: FOR YOUR SAFETY
This product must be installed by a licensed HVAC technician certified in heat
pump repair and maintenance by the jurisdiction in which the product will be
installed where such state or local requirements exists. The technician must
possess and comply with all certifications and regulations regarding the
purchasing, handling, transportation and reclamation of R410A refrigerant. In
the event no such state or local requirement exists, the installer or
maintainer must be a professional with sufficient experience in pool equipment
installation and maintenance so that all of the instructions in this manual
can be followed exactly. Before installing this product, read and follow all
warning notices and instructions that accompany this product. Failure to
follow warning notices and instructions may result in property damage,
personal injury, or death. Improper installation and/or operation can create
an electrical hazard which can cause serious injury, property damage, or
death. Improper installation and/or operation may void the warranty
These instructions are to be used with the following Jandy Replacement Kits:
R0960900
Laminar Jet with RGBW LED Light Replacement Kit
JLPBBL — Laminar Jet Lid and Collar, Pebble
JLPWTR — Laminar Jet Lid and Collar, Pewter
WARNING
- If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
- RISK OF ELECTRIC SHOCK WHICH CAN RESULT IN SERIOUS INJURY OR DEATH. Before attempting installation or service, ensure that all power to the device is disconnected/turned off at the circuit breaker.
This document gives instructions for replacing an existing laminar jet with a
Jandy Laminar Jet with LED Light.
The instructions were written with safety as the priority and must be followed
exactly. Not following the written procedure or taking shortcuts may increase
the risk
of personal injury. Read through the instructions completely before starting
the procedure. Before starting the procedure, use the parts list at the back
of these instructions to identify the parts that are in your kit. If any parts
are missing from the kit please call your local distributor for assistance.
For technical assistance, please contact our Technical Support Department at
1.800.822.7933 (US and Canada) or 1-800-688-552 (Australia).
Retrofitting a Jandy JDJ1001 Laminar Jet
-
Remove the two (2) screws that secure the laminar jet cover.
-
Lift up the cover/jet housing assembly and unscrew the two (2) flexible PVC hose union fittings that are attached to the bottom of the jet housing.
-
Unscrew the fiber optic fitting on the bottom of the housing to release the fiber optic cable. See Step 9 before removing the fiber optic cable.
-
Remove the cover/jet housing from the canister.
-
If the canister is installed in a planter, the collar can be replaced by pulling the old collar out of the canister and installing the new one.
NOTE The collar can not be removed from the canister if the laminar jet canister is already installed in the concrete pool deck. In this case, the new lid can be used with the old canister collar. -
Cut the flexible PVC hose that is attached to the union fitting without the o-ring 3″ (8 cm) from the plastic tee pipe in the canister. Note: The union fitting with the o-ring will be attached to the new jet body.
NOTE Do not cut the plastic tee pipe that is cemented to the bottom of the canister. This tee pipe is a nonstandard pipe size that will not fit standard fittings and reducers. -
Glue a standard PVC 1/2″ (1.5 cm) slip cap to the end of the cut PVC hose using PVC cement.
-
Screw the union fitting with the o-ring directly on the union fitting of the flexible hose attached to the new jet body.
-
Install the laminar jet with LED light by following Section 4 of the enclosed “Laminar Jet Installation and Operation Manual” by routing the replacement LED light cable through the conduit. Tape the end of the existing fiber optic light cable to the LED light cable so that the LED light cable can be pulled through the conduit.
-
Set up and operate the laminar jet by referring to Section 6.2 through Section 8 of the manual.
Retrofitting a Fiberstars®* or Pentair®** Laminar Jet
-
Remove the cover/housing assembly.
-
Disconnect the water lines and the fiber or LED cable attached to the jet housing.
-
Using a standard pipe coupler or reducer, glue the existing water inlet tubing of the canister to the 3/4” (2 cm) pipe spigot that is attached to enclosed flexible hose assembly. See Figure 1.
NOTE Do not cut the flexible PVC hose or the hose attached to the new Jet Body. These hoses are a nonstandard size and will not accept standard pipe fittings. If you need to reduce the total hose length as space allows, only cut the old hose. -
Install the laminar jet with LED light by following Section 4 of the enclosed “Laminar Jet Installation and Operation Manual” and by using the existing fiber optic light cable to pull the new LED light cable through the conduit.
-
Set up and operate the laminar jet by referring to Section 6.2 through Section 8 of the manual.
Replacement Kit Lists
The following table is for your reference. To order additional parts, please contact your local distributor.
ITEM NO
|
COMPONENT DESCRIPTION
|
R0960900
|
JLPBBL
|
JLPWTR
---|---|---|---|---
1| Complete Laminar Jet Assembly with LED Light Module| 1| —| —
2| Flexible Hose Assembly| 1| —| —
3| Canister Collar, Pebble, Laminar Jet| —| 1| —
4| Canister Lid, Pebble, Laminar Jet| —| 1| —
5| Canister Collar, Pewter, Laminar Jet| —| —| 1
6| Canister Lid, Pewter, Laminar Jet| —| —| 1
7| Screw, 10-24 x 1.125 Flat Head| —| 2| 2
8| Instructions| 1| —| —
*Fiberstars is a registered trademark of Energy Focus, Inc. **Pentair is a registered trademark of Pentair, Inc.
Zodiac Pool Systems LLC
2882 Whiptail Loop # 100, Carlsbad, CA 92010
www.ZodiacPoolSystems.com
Zodiac Pool Systems Canada, Inc.
2-3365 Mainway, Burlington, Ontario L7M 1A6
www.ZodiacPoolSystems.ca
USA | Jandy.com | 1.800.822.7933
Canada | Jandy.ca | 1.888.647.4004
©2021 Zodiac Pool Systems LLC. All rights reserved. Polaris® and the 3-wheeled
cleaner design are registered trademarks of Zodiac Pool Systems LLC. All other
trademarks referenced are the property of their respective owners.
References
- Jandy Swimming Pool Equipment | Canada | Jandy
- Zodiac Pool Systems Canada - English | Zodiac Pool Systems
- Zodiac Pool Systems United States | Zodiac Pool Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>