ASC SP009 Solar Water Pump Kit User Guide

ASC SP009 Solar Water Pump Kit

Product Information

Package Contents:

• 1 x Water Pump with 16 ft. Cable
• 1 x LED Light Ring with 16 ft. Cable
• 1 x Battery Control Box
• 2 x Solar Panels with 6.5 ft. Cable
• 2 x Solar Panel Bracket
• 4 x Extension Tube
• 2 x Ground Spike
• 1 x Set of Fountain Nozzles
• 1 x Remote Control (Remote Control Version Only)

Notes:
If there is any damage to the product or missing parts, please contact us at 1-626-582-8898 or www.allsolarcentral.com/contactus

Assembly Steps:

1. Connect the bracket, tubes, and spike together. Then attach the solar panel to the bracket. Slide the holding bracket into the inside lip of the top half of the solar panel frame. The bracket holds the weight of the solar panel. The solar panel can be adjusted for optimal sunlight by using the wingnut. Please refer to the diagram.
2. Insert the spike into the ground. Position the solar panel so it’s facing south (in the northern hemisphere) as much as possible to maximize daylight hours. It is important to angle the solar panel to face the sun when the sun is at its highest point. Ensure the solar panel is not shaded by trees, shrubs, or buildings.
3. Connect the Solar Panel, LED Light, and Pump to the Battery Control Box. Slightly twist the connectors when connecting to make sure the rubber seals are fully in the grooves. Refer to the diagram below:
4. The assembled Solar Pump should look like this:

Battery Control Box Operation

Note: LED light is designed to work at night only

usage. Press [Power] button, the top indicator light [On] will be
on. The pump will run continuously until the battery runs out of
power. The pump will automatically restart when the battery is
recharged under proper sunlight.
2-4hrs Timer| This mode allows you to set a timer for the pump to run for 2,
3, or 4 hours. Press the [Power] button on the Battery Control Box to
activate the system; then press the corresponding number on the
remote control: [2] for 2 hours, [3] for 3 hours, or [4] for 4
hours.
Winter mode| This mode is designed to extend the battery lifetime during the
winter. The pump’s performance depends on the orientation of the
solar panel towards the sun and the strength of sunlight.

Remote Control Operation (Remote Version Only)

Performance of the Pump
The performance of the pump depends on the orientation of the solar panel towards the sun and the sunlight strength. In order to achieve maximum performance, please make sure the panel is facing in the direction of the sun. A solar panel positioned in the shade or in poor weather will not maximize the charge. This model’s pump performance will depend on the battery power level. The pump will not work if the battery power is too low.

SP009 Solar Water Pump Kit Instructions

By All Solar Central
www.allsolarcentral.com.

Thank you from the entire ASC family for purchasing an ASC solar product! Please read this entire booklet before assembly.

Package contents

• 1 x Water Pump with 16 ft. Cable
• 1 x LED Light Ring with 16 ft. Cable
• 1 x Battery Control Box
• 2 x Solar Panels with 6.5 ft. Cable
• 2 x Solar Panel Bracket
• 4 x Extension Tube
• 2 x Ground Spike
• 1 x Set of Fountain Nozzles
• 1 x Remote Control (Remote Control Version Only)

Notes:
If there is any damage to the product or missing parts, please contact us at 1-626-582-8898 or www.allsolarcentral.com/contactus.

Assembly Steps

1. Connect the bracket, tubes and spike together. Then attach the solar panel to the bracket. Slide the holding bracket into the inside lip of the top half of the solar panel frame. The bracket holds the weight of the solar panel. The solar panel can be adjusted for optimal sunlight by using the wingnut. Please see the diagram.

2. Insert the spike into the ground. Position the solar panel so it’s facing south (in the northern hemisphere) as much as possible to maximize daylight hours. It is important to angle the solar panel to face the sun when the sun is at its highest point. Ensure the solar panel is not shaded by trees, shrubs, or buildings.

3. Connect the Solar Panel, LED Light, and Pump to the Battery Control Box (See diagram below:)
   IMPORTANT!
   Slightly twist the connectors when connecting to make sure the rubber seals are fully in the grooves.

4. The assembled Solar Pump should look like this:

5. BATTERY CONTROL BOX OPERATION
   Note: LED light is designed to work at night only
   The solar pump is designed mainly for use during summer hours, but it will also work in spring and fall as long as the sunlight conditions are good enough in your region. And the new Winter Mode will extend battery lifetime during the winter. The pump’s performance depends on the orientation of the solar panel towards the sun (see section 2) and the strength of sunlight. This ASC solar pump kit comes with three operation modes: Continuously On, 2-4hrs Timer, and Winter mode.

   • CONTINUOUSLY ON MODE: This mode works best if you want to maximize the pump’s daily usage. Press the [Power] button, and the top indicator light [On] will be on. The pump will run continuously until the battery runs out of power. The pump will automatically restart when the battery is recharged under proper sunlight.
   • DAILY TIMER MODE: This mode works best if you want the pump to run at the same time every day (The time you start the mode). Press the [Timer] button repeatedly until the indicator light [2hrs], [3hrs] or [4hrs] is lit –the pump will run for 2, 3, or 4 hours and shut down (in standby) for 22, 21, or 20 hours. This setting will repeat at the same time every day. You can reset the pump’s daily start-up time by switching it to a new desired time using this mode.
   • WINTER MODE: This mode works best in winter or poor weather. Press the [Winter] button and the top indicator light [Pulse] will be on. The pump will run for 20 seconds in every 60 seconds. It is recommended to use this mode to extend battery lifetime in winter or poor weather.
   • PUMP FLOW CONTROL button: Use this button to adjust the water flow rate. Press [Flow Rate] repeatedly to adjust the water flow rate (total 3 levels). Notes: A higher water flow rate will consume more power and reduce the battery lifetime.
   • LOW BATTERY light: The [Low Bat.] indicator light will be blinking when the battery is low, and the pump/LED light will shut down shortly to protect the battery. The [Low Bat.] indicator light will turn off until the battery is recharged.

6. REMOTE CONTROL OPERATION (Remote Version Only)

   • Press the [Power] button on the Battery Control Box to activate the system; then press the remote:
   • [On] = CONTINUOUSLY ON MODE
   • [2] = Daily Timer Mode 2 Hours
   • [3] = Daily Timer Mode 3 Hours
   • [4] = Daily Timer Mode 4 Hours
     IMPORTANT!
     You have to press the [Power] button in the battery box to switch on the battery system at first, then you can select the function by pressing the button on the remote control.

7. PERFORMANCE OF THE PUMP
   The performance of the pump depends on the orientation of the solar panel towards the sun and the sunlight strength. In order to achieve max performance, please make sure the panel is facing in the direction of the sun. A solar panel positioned in the shade or in poor weather will not maximize the charge. This models pump performance will depend on the battery power level. The pump will not work if battery power is too low.

8. PUMP MAINTENANCE

9. O PUMP CASE

10. IMPELLER COVER

11. IMPELLER

12. PUMP

13. FILTER
    If you find the pump starts losing power or stops working, please clean the pump filter and impeller with clean water.

14. BATTERY REPLACEMENT
    If properly maintained this solar pump has been designed to run for many years. The Lead-acid battery does have a limited life span and might need to be replaced after 18-24 months of use. If the battery appears less efficient, please try to boost charge it. To do this, leave the system off for 2 to 3 sunny days to allow full charge to the battery. It is recommended to do this occasionally to maximize battery lifetime.
    To replace the battery, please follow these steps:

    • Remove the screws from the Battery Box
    • Remove the lid and control panel from the battery box slightly
    • Disconnect the battery connectors, then remove and replace the old battery.
      NOTES: Please make sure to connect the new battery correctly: Red for + and Black for -. Only the original battery should be used for replacement as other alternatives may be incompatible and may damage the control panel and will void the warranty. For parts, please go to www.allsolarcentral.com.

TROUBLESHOOTING

• Check to see if the solar panel, pump, and LED light are connected properly
• Check to see if the solar panel is correctly positioned facing the sun. Please ensure the solar panel is not in the shade or obstructed by trees, shrubs, or a building (see step 2).
• Check if [low bat.] light is on. If so, this indicates that the battery power is low. Switch off the pump and leave the solar panel charging under direct sunlight for 1 or 2 days.
• CHARGING TIPS: Press the button [Power] to turn off the system. All indicator lights should be off. All solar power will now be used to charge the battery.
• Check the water level and make sure the pump is fully submerged in water
• Check to see if the pump filter/impeller is blocked by debris
• Check to see if the fountain tubing is blocked by kinks or obstructions
• Check the pump. It may be “air locked”. Turn the pump on/off switch several times to clear any air that may have been trapped.

TECHNICAL DATA

• Max. Water Flow: 1500LPH
• Max. Water Lift: 300CM
• Max. Fountain Height: 160CM
• Working Voltage: DC15V – DC18V
• Pump Working Power: 6.6W – 11.2W
• Protection Grade of Pump: IP68
• Solar Panel: 2 x 8.0W; 18V; 0.444A
• Solar Panel Size: 2 x 358x238x18mm
• Protection Grade of Panel: IP44
• Battery: Lead-acid 12V/5AH
• Protection Grade of Battery Box: IP44
• LED Light Working Voltage: DC12V
• LED Light Working Power: 0.12W
• Protection Grade of LED Light: IP68

WINTER PROTECTION
Indoor storage is recommended during winter months. Normal operating temperature is between 50 and 113 °F. The battery can be recharged at temperatures between 32 and 113 °F.

IMPORTANT:

• In order to keep your battery healthy during long storage times, please make sure the battery is fully recharged before storing.
• To do this, turn off the pump by pressing the button [Power] and charge the battery for 1 or 2 sunny days. See Step 10 – Charging Tips

PROPOSITION 65 WARNING:
Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. For more information go to
https://www.p65warnings.ca.gov/.

BATTERY DISPOSE:
Never dispose of batteries in the garbage. Disposal of batteries in the garbage is unlawful under state and federal environmental laws and regulations. Always take used batteries to your local battery recycling center.

Please visit www.allsolarcentral.com for more products and offers.

https://manual-hub.com/.

References

• AllSolarCentral: Eco-Friendly Solar Powered Water Pump and Fountains – Allsolarcentral.com
• Contact Us – Allsolarcentral.com
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>