imperii RR FIERRO SmartWatch Tend IP68 Instruction Manual
- June 7, 2024
- imperii electronics
Table of Contents
TE.03.0285
PRODUCT SKETCH
a-The main body of the bracelet b-Wristband wristband/needle c- Charging clip
PRODUCT INSTALLATION
Step 1: The needle is inserted along the groove of the strap.
Step 2: Align the card strap with the card hole on one side of the wristband
display, press the handgrip to the left, release the handgrip, and snap into
the card hole of the display.
Step 3: Pressing the hands of the hands into the grooves of the strap, the
installation is completed.
WRISTBAND WEAR
1. Wear the bracelet a finger away from the wrist and adjust the trap to the
comfort position.
2. Fasten the wrist strap with the pin to a comfortable position, tighten the
wrist strap and fasten it.
Tip : Wearing too loose may affect the heart rate sensor to collect data.
APP CONNECTION METHOD
http://www.iwhop.com/app.php/Update/android
WearFit2.0 APP QR code
(WearFit2.0 allows the use of mobile app features)
1. Sean the QR code above, or search for “WearFit2.0” in the Android App Store/APP Store to download and install the WearFit2.0 APP.
2. Start the bracelet (long-press the screen for 3 seconds), the bracelet is
close to the mobile phone, open and enter the “WearFit2.0” APP, search for
the Bluetooth bracelet according to the APP connection wizard, complete the
pairing connection.
Tip: Apple device iOS system will prompt the Bluetooth pairing request after
the first APP connection, click the “pricing” connection, the bracelet can
take over the notifications from the iOS system to push calls, text messages,
etc.
USAGE
-
The dial interface slides up, switches to the bracelet information interface, and slides down to return to the dial interface.
-
The dial interface slides up, switches to the bracelet information interface, and slides down to return to the dial interface.
-
Press and hold the dial interface to enter the dial selection mode, slide the dial to the left or right, and click the interface to select the dial.
-
The dial interface slides to the left, switches to the function list interface, slides up and down to select the function, and right slides back to the dial interface. Function list interface, click a function to enter the function’s secondary interface, such as: click heart rate, then enter the heart rate measurement interface. All secondary interfaces, rught slide back to the upper inetrface and slide back to the dial interface.
RAISE YOUR HAND TO BRIGHTEN THE SCREEN
Method 1:The hand swings from the vertical position to the normal watch
posture, the surface angle is between 30° – 85°, and the bracelet will
automatically light up.
Method 2: The surface stays slightly outward, and the inner rotation rotates
to the normal viewing angle (between 30° and 80°), and the bracelet
automatically lights up.
CHARGING METHOD
When the bracelet reminds you that the battery is low, please charge it in time
BASIC PARAMETERS
| Screen size | 1,3pulgadas |
|---|---|
| Bluetooth | Bluetooth 4.0 |
| Waterproof level | IP67 waterproof rating |
| Type of battery | Lithium polymer battery |
| Battery capacity | 170mAh |
| Charging time | Normal use for 8 days, standby for 60 days |
| Wristband size | 245 x 20 x 2,6mm |
| Charging method | Charging clip charging, charging voltage 5V |
| Touch screen form | Full-screen touch |
| Packing | Smart Bracelet + Charging Clip + Product Manual |
TECHNICAL SERVICE:
http://www.imperiielectronics.com/contactenos
Importado por:
B85947513
www.imperiielectronics.com
Pol. Ind. Neisa Sur
Avd. Marconi, Bloque 1, Nave 13
28021 Madrid
Made in PRC
imperii RR FIERRO SmartWatch Tend IP68 Instruction Manual – Download
[optimized]
imperii RR FIERRO SmartWatch Tend IP68 Instruction Manual –
Download
imperii RR FIERRO SmartWatch Tend IP68 Instruction Manual – OCR
[PDF]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>