Rebel URZ0986 Paper Shredder User Manual
- June 13, 2024
- Rebel
Table of Contents
Rebel URZ0986 Paper Shredder
Product Overview
1
| Mode switch (REV/ OFF/AUTO)
---|---
2
| Paper/credit card entry slot
3
| CD/DVD entry slot
4
| Shredder head
5
| Window
6
| Wastebasket
SAFETY INSTRUCTIONS
Read the instruction manual carefully before first use and keep it for future reference. Producer is not responsible for damages caused by inappropriate handling and use of the device.
- Before connecting the device to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in thepower supply socket.
- Protect this device from moisture, humidity, water and any other liquid. Avoid using/storing it in extreme temperatures. Do not expose it to direct sunlight and sources of heat.
- Make sure the power outlet is nearby.
- Product suitable for indoor use only.
- Make sure to place this device on flat, dry and stable surface.
- Do not place heavy objects on the device.
- Disconnect the device from the power supply if it is not going to be used for a long time.
- Protect power cord from harp edges and other factors which could lead to its damage
- When you disconnect the power cord of the device, grasp and pull the plug, not the cord/cable.
- Do not use this device if it has been damaged or its operation is abnormal.
- Do not attempt to repair this device yourself. In case of damage, contact with an authorized service point for check-up/repair.
- This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and allthe safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
- Fixed power cable may only be replaced in an authorized service point.
- ALWAYS disconnect this device from power supply mains before cleaning and emptying the wastebasket.
- Clean this device with soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean this product
- Pay attention to the safety symbols on the top of the shredder and operate the device accordingly.
- The device is not intended for commercial use.
WARNING SYMBOLS
| **** | Exercise caution. |
|---|---|
| **** | Read the instruction manual carefully before first use. |
| **** | Keep away from children and pets. |
| **** | Do not reach into entry slots. |
| **** | Keep your hair away from entry slots as they may become entangled in |
it.
| Keep your tie and other loose clothing away from entry slots.
| Do not spray anything on or into the shredder.
| The shredder does not accept paper clips. Remember to remove them
before inserting paper.
| Keep loose jewellery away from entry slots.
****| Do not exceed the maximum capacity of the paper entry slot.
IMPORTANT: The shredder is equipped with two separate cutting heads, wastebasket for paper and credit card waste and tray for CD, DVD shards. Make sure you insert material to be shredded into appropriate entry slots. Do not insert any other objects than those allowed into the entry slots.
Do not shred CDs, DVDs, credit cards and paper at the same time!
The device is designed for 3 minutes of continuous use. Afterwards, let it rest for another 40 minutes. Not complying with the above may result in overheating.
OPERATION
Paper/credit card shredding:
-
Mount the shredder head on the wastebasket in such a way that the CD/ DVD entry slot is above the dedicated tray. Be careful not to pinch your fingers between the top edge of the wastebasket and the shredder head.
-
Make sure the Mode switch is in OFF position before connecting the device to power supply socket.
-
Connect the device to power supply socket.
-
The device has three modes:
• AUTO (automatic start and stop): Shredding will start automatically once the paper is inserted into the entry slot. It will stop automatically once the paper has been successfully shredded.
• REV (reverse):
» The cutting head runs in reverse and pushes the paper out of the cutting head. Use this mode if any jams occur.
• OFF: Turn off the device. Set to this position when emptying the wastebasket, before cleaning, transporting or if not in use for a longer period of time. -
Set the Mode switch to AUTO position.
-
Make sure the paper is dry, clean and free of any wrinkles. Crumpled paper may jam the cutting head.
-
Make sure the paper is neatly stacked. Splayed sheets may jam the cutting head.
-
Insert the paper into the center of the paper entry and release. Shredding will start automatically.
IMPORTANT! Make sure not to insert more than 10 sheets per single pass Otherwise, the paper may jam in the cutting head! -
When shredding small paper sizes such as letters or receipts, insert them into the center of the entry slot. Insert credit cards lengthwise into the entry slot.
-
Cutting head will stop once the shredding process is complete.
-
Check the fill level in the wastebasket and CD/DVD tray regularly. When it is full, empty it immediately.
CDs and DVDs shredding:
-
Insert the CD/DVD tray into the appropriate place inside the wastebasket.
-
Make sure the shredder head is mounted properly.
-
Set the Mode switch to AUTO position.
-
Insert a CD or DVD into the center of the CD/DVD entry slot.
-
Shredding starts automatically.
IMPORTANT! Only one CD or DVD can be shred at a time. -
CDs and DVDs are shredded into three pieces which are collected in a dedicated tray inside the wastebasket.
- Make sure to empty the tray regularly
PAPER JAMS
If the following situations occur, the cutting head may jam:
- Too much paper was inserted into the paper entry slot in single pass.
- Paper was inserted incorrectly into the paper entry slot.
- Inserted paper was not stacked neatly.
- Paper was crumpled.
- The wastebasket is overfilled with cutting waste.
To clear the jam, set the Mode switch to REV position. Cutting head runs in reverse ejecting the paper out.
OVERHEAT PROTECTION
If continuous operation of the device exceeds 3 minutes, motor may overheat
and the device will automatically turn off. Please wait around 40 minutes
until motor temperature drops to the safe level. Then turn on the device by
setting the Mode switch to AUTO position.
CLEANING AND MAINTENANCE
-
Make sure to disconnect the device from power supply socket prior to cleaning.
-
Clean this device with soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean this product.
-
Empty the wastebasket regularly. Otherwise, the cutting head may jam due to overfilling.
Note! Make sure to set the Mode switch to OFF position before emptying the wastebasket. -
If necessary, use a suitable tool to remove jammed paper from the cutting head.
CAUTION!
- Make sure to unplug the device from power supply socket before manual removing jammed paper from the cutters.
- The cutters in the cutting head are sharp! Exercise caution and do not reach directly into the cutters to avoid injuries!
TROUBLESHOOTING
| Problem | Possible reason | Possible solution |
|---|---|---|
| After finishing shredding, the motor still runs | There is too much shredded |
paper in the wastebasket so that the paper which is being shredded cannot fall
down and leave the cutting head| Cut off the power and empty the wastebasket
Paper feed and cutting mechanism rotation is normal but there is still some
scrapped paper hanging at the output of the cutting head| Shredded paper has
been clamped by the blades| Set the mode switch to the REV position (if
needed, clean the
shredded paper at the output of the cutting
head)
Paper is in the entry but the shredder doesn’t work| Paper wasn’t inserted
into the entry properly| Make sure the paper touches the entry slot at its
whole width (the paper is inserted as straight as possible)
The paper is jammed and the blades stop rotating| The number of inserted paper
exceeds max sheet capacity| Set the mode switch to REV position and remove
jammed paper
Locked motor activates the overheat protection| Unplug the shredder, then plug
it again and let it cool down for a while
The shredder doesn’t start after inserting a sheet of paper| The paper is too
thin, too soft, humid or too crinkly to activate the sensor| Fold the paper in
half and try again; make sure the paper is clean and dry
Set the mode switch to REV position
SPECIFICATIONS
Automatic start/stop function
Reverse function
Removable head for easy emptying
Two separate cutters and wastebaskets for paper and CDs, DVDs, credit cards
Window indicating fill level
Protection against overheat
- Suitable for: home / office
- Can shred: paper, CDs, DVDs, credit cards, staples
- Shreds per single pass (A4 80 g/m2): 10 sheets
- Cut type: micro-cut
- Cut size: 5 x 16 mm
- DIN security level: P-4
- Paper entry width: 220 mm
- Wastebasket capacity: 21 l
- Shredding speed: 2,25 m/min
- Operating cycle: 3 min on / 40 min off
- Noise level: 70 dB
- Power: 380 W
- Power supply: 220 – 240 V; 50/60 Hz; 1,7 A
- Weight: 5,2 kg
- Dimensions: 360 x 244 x 498 mm
- Power cord length: 120 cm
English
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or Its literature, indicates that It should not be disposed with other household wastes at the end of its working life. To prevent possible harm lo the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office,for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal.
