VEVOR 110202 Motorcycle Lift Scissor Jack Stand User Manual
- June 13, 2024
- VEVOR
Table of Contents
VEVOR 110202 Motorcycle Lift Scissor Jack Stand
Model: 110202
Product Information
- Rated capacity: 1100 LBS
- Minimum height: 89 mm
- Maximum height: 338 mm
- G.W. (kg): 15
Caution:
- Read and understand the user manual before assembling, installing, or operating the lift platform.
- Keep the surface clean, tidy, and free from unrelated materials. Ensure that there is adequate lighting.
- Always keep your hands and feet away from the working area.
- Do not allow untrained persons to operate the lift.
- Do not make any modifications to this lift.
Maintenance:
- When not in use, the lift must be stored in the lowest position in a dry location.
- Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts.
- Before each use, check all parts. If any part of the lift is damaged or suspect, remove the lift from service and take necessary action to repair.
Parts List:
| Part No | Description | Qty | Part No | Description | Qty |
|---|---|---|---|---|---|
| 1 | Platform | 1 | 13 | Washer M20 | 4 |
| 2 | Saddle | 2 | 14 | Outside lifting arm | 1 |
| 3 | Washer M12 | 10 | 15 | Connect pin | 1 |
| 4 | Adjustable plate | 2 | 16 | Middle bush | 1 |
| 5 | Inside frame roller | 2 | 17 | Bearing | 2 |
| 6 | Lifting screw | 1 | 18 | Inside lifting arm | 1 |
| 7 | Handle | 1 | 19 | Outside fixing spindle | 1 |
| 8 | Inside fixing spindle | 1 | 20 | Fixing nut | 1 |
| 9 | Spring blocking | 4 | 21 | Lock nut M6 | 1 |
| 10 | Base plate | 1 | 22 | Inside removable spindle | 1 |
| 11 | Outside frame roller | 2 | 23 | Safety Pin | 1 |
| 12 | Washer M20 | 4 |
Contact Information:
If you have any product questions or need technical support, please feel free to contact us at CustomerService@vevor.com.
Manufacturer and Importer Details:
- Manufacturer: Zhejiang Jinhong Auto Accessory Co., Ltd.
- Address: No.36 Binhai Road, Jianshan, Haining, Zhejiang, China
- EU Importer: WAITCHX 250 bis boulevard Saint-Germain 75007 Paris
- UK Importer: FREE MOOD LTD, 2 Holywell Lane, London, England, EC2A 3ET
- UK REP: EUREP UK LTD UNIT 2264, 100 OCK STREET, ABINGDON OXFORDSHIRE ENGLAND OX14 5DH
- EUREP GmbH EC REP Unterlettenweg 1a, 85051 Ingolstadt, Germany
For additional technical support and e-warranty certificate, please visit www.vevor.com/support.
Additional Information:
Please note that the appearance of the product may vary from the illustrations in the manual. VEVOR reserves the right to interpret the user manual. We apologize for not informing you about any technology or software updates on our product.
MADE IN CHINA
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only
represents an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and doses not necessarily mean to
cover all categories of tools offered by us. You are kindly reminded to verify
carefully when you are placing an order with us if you are actually saving
half in comparison with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
Operation
- Rotate the screw by ratchet wrench to adjust the height of the platform.
- Adjust the platform to the appropriate height and place the lift to the bottom of the motorcycle. Make sure that the center of the load align with the pivot, and keep the load stable and safe.
- When all this is done, lift the motorcycle to the proper height and insert the safety pin.
- Tighten the motorcycle with other tools to keep it stable.
- After repairing, pull out the safety pin，rotate the ratchet wrench slowly and gently to lower the platform until it departs from pivot, and then take the lift away.
PECIFICSATIONS
Model| Rated
capacity( LBS)
| Minimum
height(mm)
| Maximum
height(mm)
| G.W.(kg)
---|---|---|---|---
110202| 1100| 89| 338| 15
CAUTION
- Read and understand the user manual before assembling, installing, operating, or servicing this product. Failure to follow these warnings and instructions can cause death, personal injury or damage to valuable property. And Keep the user manual .
- Do not overload the Engine Stand. Never exceed the maximum weight capacity of 1100 Lbs.
- Keep the load stable and prevent the load from losing balance.
- Before using, lubricate the screw and the nuts with grease to make the lift flexible and antifriction.
- Use this lift for second-lift purpose only. Do not use it for any other purpose it is not designed to perform.
- Keep children and unauthorized persons away from the work area.
- Wear ANSI approved safety goggles when operating the lift.
- Only use this lift on a big , stable ,level, dry and not slippery motorcycle lift platform. Keep the surface clean,tidy and free from unrelated materials and ensure that there is adequate lighting.
- Always keep your hands and feet away from working area.
- Do not allow untrained persons to operate the lift .
- Do not make any modifications to this lift.
MAINTENANCE
- When not in use, the lift must be stored in the lowest position in a dry location.
- Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts.
- Before each use check all parts. If any part of the lift is damaged or suspect , remove the lift from service and take necessary action to repair.
PARTS LIST
Part No
| ****
Description
| ****
Qty
| ****
Part No
| ****
Description
| ****
Qty
---|---|---|---|---|---
1| Platform| 1| 13| Washer M20| 4
2| Bolt M12×50| 2| 14| Outside lifting arm| 1
3| Washer M12| 10| 15| Connect pin| 1
4| Saddle| 2| 16| Middle bush| 1
5| Adjustable plate| 2| 17| Inside frame roller| 2
6| Bolt M10×25| 2| 18| Inside lifting arm| 1
7| Handle| 1| 19| Bearing| 2
8| Lifting screw| 1| 20| Outside fixing spindle| 1
9| Inside fixing spindle| 1| 21| Fixing nut| 1
10| Spring blocking| 4| 22| Lock nut M6| 1
11| Base plate| 1| 23| Inside removable spindle| 1
12| Outside frame roller| 2| 24| Safety Pin| 1
EU Importer: WAITCHX， 250 bis boulevard Saint-Germain 75007 Paris
UK Importer: FREE MOOD LTD, 2 Holywell Lane, London, England, EC2A 3ET
UK REP
EUREP UK LTD
UNIT 2264, 100 OCK STREET, ABINGDON OXFORDSHIRE ENGLAND OX14 5DH
EC REP
EUREP GmbH
Unterlettenweg 1a, 85051
Ingolstadt, Germany
Manufacturer: Zhejiang Jinhong Auto Accessory Co., Ltd. Address: No.36 Binhai Road, Jianshan, Haining, Zhejiang, China MADE IN CHINA
Technical Support and E-Warranty Certificate
www.vevor.com/support
MADE IN CHINA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>