ELATION KL Fresnel 8 P.O. FC LED lens headlight User Manual

: June 4, 2024
: ELATION

KL FRESNEL 8 FC PO
User Manual

ELATION KL Fresnel 8 P.O. FC LED lens headlight

KL Fresnel 8 P.O. FC LED lens headlight

©2021 ELATION PROFESSIONAL all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ELATION brands and product names are trademarks or registered trademarks of their respective companies.
ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.
Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 | 323-832-9142 fax | www.elationlighting.com | info@elationlighting.com
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands
+31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu
Elation Professional Mexico | AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000 +52 728-282-7070
DOCUMENT VERSION

https://qrs.ly/23cbwjh

Due to additional product features and/or enhancements, an updated version of this document may be available online. Please scan the QR Code with your mobile device or visit www.elationlighting.com for the latest revision/update of this manual, before installation and/or programming.

Date| Document Version| Software Version| DMX Channel Mode| Notes
---|---|---|---|---
07/12/21| 1.0| 1.0.1| 1/6/11/18/9/14| Initial Release

GENERAL INFORMATION

INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device. These instructions contain important safety and use information.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton is damaged, carefully inspect the device for damage, and be sure all accessories necessary to install and operate the device have arrived intact. In the event that damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this device to your dealer without first contacting customer support. Please do not discard the shipping carton in the trash. Please recycle whenever possible.
BOX CONTENTS
Gel Frame (x1)
Barn Doors (x1)
Junior Pin (1 1/8” – 28mm) (x1)
Locking Power Cable (x1)
CUSTOMER SUPPORT
Contact ELATION Service for any product-related service and support needs. Also visit forums.elationlighting.com with questions, comments, or suggestions.
ELATION SERVICE USA – Monday – Friday 8:00am to 4:30pm PST 323-582-3322 | Fax 323-832-9142 | support@elationlighting.com
ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET +31 45 546 85 63 | Fax +31 45 546 85 96 | support@elationlighting.eu
REPLACEMENT PARTS please visit parts.elationlighting.com
IMPORTANT NOTICE!
THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/ OR REPAIRS.

WARRANTY RETURNS (USA ONLY)

To obtain warranty service, a Return Materials Authorization (RMA) number must first be obtained from ELATION. It is the Customer’s responsibility to provide product proof of purchase and serial number by acceptable evidence such as an invoice copy or an approved ELATION Extended Warranty Certificate (“EWC”) and any relevant maintenance records at the time warranty service is sought. Failure to provide acceptable evidence of product proof of purchase or EWC and any relevant maintenance records may be cause for denial of warranty service.
Products returned for warranty service must be sent without any accessories (i.e., power, data, and safety cables, brackets, clamps, rigging hardware, frost filters, gel frames, barn doors, lenses, hoses, nozzles, rack mounting hardware, etc.), must be boxed using the original and/or suitable packaging materials (double-box and foam) that provides ample product protection for ground and/or air freight transit, and must be shipped freight pre-paid and insured to ELATION in Los Angeles, CA or an ELATION Authorized Service Center. The RMA number must be clearly written on the outside of the return box, and a brief description of the problem and the RMA number must be documented and included in the box.
Products returned for warranty service without an RMA number clearly marked on the outside of the package will be refused and returned to the shipper at the Customer’s expense. Products returned for warranty service, which are received damaged due to inadequate and/or improper packaging and/or due to damage caused by the shipping carrier, may incur additional repair charges before warranty service begins and/or may void this warranty. If any product accessories (included and/or optional) are shipped with the product, ELATION and/or the ELATION Authorized Service Center shall have no liability whatsoever for the loss and/or damage to any such accessories, nor the safe return thereof. If the requested warranty repairs or service (including parts replacement) are within the terms of this warranty, ELATION will pay return ground transportation shipping charges to a single designated point within the United States.

SAFETY GUIDELINES

This fixture is a sophisticated piece of electronic equipment. To guarantee smooth operation, it is important to follow all instructions and guidelines in this manual. Elation Professional is not responsible for injury and/or damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform the installation of this fixture and only the original rigging parts included with this fixture should be used for installation. Any modifications to the fixture and/or the included mounting hardware will void the original manufacturer’s warranty and increase the risk of damage and/or personal injury.
PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED.
THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF. DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
DO NOT PLUG THIS UNIT INTO A DIMMER PACK DO NOT REMOVE THE COVER UNDER ANY CONDITIONS NEVER OPERATE THIS UNIT WITH THE CASING REMOVED UNPLUG FROM POWER DURING LONG PERIODS OF NON-USE DISCONNECT POWER BEFORE PERFORMING MAINTENANCE
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK – MAY INDUCE BLINDNESS! SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
FOR USE IN INDOOR OR DRY LOCATIONS ONLY!
DO NOT EXPOSE TO RAIN AND/OR MOISTURE!
THE FIXTURE SHOULD BE PLACED A MINIMUM OF 1.0 FEET (0.3 METERS) FROM ANY NEARBY OBJECTS OR SURFACES.
THE FIXTURE SHOULD BE PLACED A MINIMUM OF 1.6 FEET (0.5 METERS) FROM ANY FLAMMABLE MATERIALS.
THE MAXIMUM AMBIENT OPERATING TEMPERATURE IS 113°F (45°C)
IP20 IP20 RATING
PROTECTED AGAINST SOLID OBJECTS OF FINGER-SIZE OR LARGER NOT PROTECTED AGAINST LIQUID INTRUSION OF ANY KIND!

SAFETY GUIDELINES

For Your Own Personal Safety, Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit!

IP20 Rating: The fixture is protected against intrusion by solids measuring roughly 12.5mm in size or larger, such as human fingers. THE FIXTURE IS NOT PROTECTED AGAINST LIQUIDS OR MOISTURE OF ANY KIND!
Do not touch the fixture housing during operation, as it may be hot.
Do not shake the fixture, and avoid using brute force when installing and/or operating.
Use only the original packaging and materials to transport or ship the fixture for service. Make sure to retain the original packaging for this purpose.
Be sure that the local power outlet matches the required voltage for the device.
Do not open up the device for any reason. There are no user-serviceable parts inside.
Disconnect the device’s main power when left unused for long periods of time.
Never connect this device to a dimmer pack.
Do not attempt to operate this device if it has been damaged in any way.
Never operate this device with the cover removed.
Do not attempt to operate this device if the power cord has been frayed or broken.
Never force a power cord connector into the fixture. If the power cord or any of its connectors are damaged, replace it immediately with a new cord of the same power rating.
Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal shortage.
Only handle the power cord by the plug end. Never disconnect the plug by tugging on the wire portion of the power cord.
Disconnect from the main power before making any type of connection.
Never block the air ventilation slots. Always be sure to mount this device in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall. • Always mount this unit in a safe and stable matter.
Please route your power cord out of the way of foot traffic. Power cords should be routed so they are not likely to be walked on or pinched by items placed upon or against them. • Before performing any servicing, turn off and disconnect the device from power and allow at least 15 minutes for the device to cool.
Consistent operational breaks will ensure that this fixture will function properly for many years.
The device should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen on, or liquid has been spilled into, the device.
C. The device has been immersed in liquid or exposed to moisture.
D. The appliance does not appear to operate normally or exhibit a marked change in performance.
Keep all flammable materials away from this fixture!

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
CLEANING
Frequent cleaning is recommended to ensure proper function, optimized light output, and extended life. The frequency of cleaning depends on the environment in which the fixture operates:
damp, smoky or particularly dirty environments can cause a greater accumulation of dirt on the fixture’s optics. Clean periodically with a soft cloth to avoid dirt/debris accumulation.
NEVER use alcohol, solvents, or ammonia-based cleaners.
MAINTENANCE
Regular inspections are recommended to insure proper function and extended life. There are no user-serviceable parts inside this fixture. Please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from an authorized Elation dealer.
Please refer to the following points during routine inspections:

A detailed electrical check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.
Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
Check for any deformations on the housing, color lenses, rigging hardware, and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s).
Electric power supply cables must not show any damage, material fatigue, or sediments.

OVERVIEW

ELATION KL Fresnel 8 P.O. FC LED lens headlight -
OVERVIEW

FIXTURE INSTALLATION

FLAMMABLE MATERIAL WARNING
Keep fixture minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics.
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or installations.
THE MINIMUM DISTANCE TO OBJECTS/SURFACES IS 1 FOOT (0.3 METERS)
THE MINIMUM DISTANCE OF FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 METERS)
MAXIMUM AMBIENT TEMPERATURE 113° F (45°C)
DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!
Fixture MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
Before rigging/mounting a single fixture or multiple fixtures to any metal truss/structure or placing the fixture(s) on any surface, a professional equipment installer MUST be consulted to determine if the metal truss/structure or surface is properly certified to safely hold the combined weight of the fixture(s), clamps, cables, and accessories. Fixture(s) should be installed in areas outside walking paths, seating areas, or away from areas where unauthorized personnel might reach the fixture by hand.
NEVER stand directly below the fixture(s) when rigging, removing, or servicing.
Overhead fixture installation must always be secured with a secondary safety attachment, such as an appropriately rated safety cable.
Allow approximately 15 minutes for the fixture to cool down before serving.
CLAMP INSTALLATION
This device should be mounted by attaching a mounting clamp and junior pin to the mounting yoke. A safety cable loop is also located on the rear face of the fixture. When mounting the fixture to a truss or any other suspended or overhead installation, be sure to secure an appropriately rated clamp (not included) to the clamp attachment point and attach a separate SAFETY CABLE of the appropriate safety rating to the safety cable rigging point.

ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT FALL IF THE CLAMP FAILS.
RIGGING
Overhead rigging requires extensive experience, including but not limited to: calculating working load limits, understanding the installation material being used, and periodic safety inspection of all installation material and the fixture itself. If you lack these qualifications, do not attempt to perform the installation yourself. Improper installation can result in bodily injury.

ACCESSORY INSTALLATION

GEL FRAME INSTALLATION

Press and hold the clip latch indicated by the straight arrow in the image below, then flip the retaining clip located near the top of the lens.
Slide the gel frame into place in one of the accessory slots. Secure the gel frame by flipping the retaining clip back down, making sure it latches in place.

BARNDOOR INSTALLATION

Press and hold the clip latch indicated by the straight arrow in the image below, then flip the retaining clip located near the top of the lens.
Slide the barn door into place in one of the vacant accessory slots on the front of the fixture.
Return the retaining clip to the original position to lock the barn door in place.

CONTROL PANEL

The fixture includes an easy-to-navigate system menu. The control panel display is located on the side panel of the fixture (see image below) and provides access to the main system menu, where all necessary system adjustments are made to the fixture. During normal operation, pressing the MODE button once will access the fixture’s main menu. Once in the main menu, you can navigate through the different functions and access the sub-menus with the DOWN and UP buttons. Once you reach a field that requires adjusting, press the ENTER button to activate that field and use the DOWN and UP buttons to adjust the field. Pressing the ENTER button once more will confirm the setting. Exit the main menu at any time without making any adjustments by pressing the MODE button.
The display screen will shut OFF automatically after 30 seconds of inactivity. To turn the display back on, press and hold the MODE button for 3 seconds.
To enter the white balance menu, press and hold the MODE, UP, and DOWN buttons simultaneously. Please note that this will override the Color menu.

ELATION KL FRESNEL FC PO

Supports Software Versions: 1.0.1

ENCODER MODE

No DMX

| Hold Last|
Fade to Black|
Standalone|
STANDALONE| Dimmer| 0% – 100%|
CCT| 2400K – 8500K
Default = 6000K|
Green Shift| -100% – +100%
Default = 0|
Virtual Color| Color 01 – Color 53| See Color Macros Chart section for reference
PERSONALITY| Primary| On / Off|
Secondary| On / Off|
Dim Mode| Standard|
Stage|
TV|
Architectural|
Theatre|
Stage 2|
Dim Speed| 0.0s – 10.0s, default = 0.1s
Dim Curves| Linear|
Square|
Square Inverse|
S-Curve|
CONTINUED ON NEXT PAGE
ELATION KL FRESNEL FC PO

Supports Software Versions: 1.0.1
PERSONALITY (continued)| LED Refresh Rate| 900Hz – 1500 Hz, 2500 Hz, 4000 Hz, 5000 Hz, 6000 Hz, 10
KHz, 15 KHz, 20 KHz, 25 KHz
Default = 1200 Hz
LED Power Limit| 50%|
60%|
70%|
80%|
90%|
100%|
Fan Mode| Auto|
Silent|
High|

Display

ENCODER FUNCTION

When the device has been set to Encoder mode, the lighting display can be adjusted using the knob located beside the display screen on the back of the device.
To enter Encoder mode, select the ENCODER MODE option from the main system menu, as described in the System Menu section of this manual. Then use the UP and DOWN buttons to scroll through the different modes. Each mode is represented by one of the tables below. Press ENTER to select the mode that is currently displayed.
Once an Encoder Mode has been selected, press the knob to cycle through the available Parameter options. When the desired Parameter is displayed on the screen, simply turn the knob to adjust the value of that Parameter.

DIMMER MODE

PARAMETER| VALUE| RESOLUTION| DEFAULT
Intensity| Intensity 0-100%| 1%| 0%
INT CCT GRN MODE

PARAMETER| VALUE| RESOLUTION| DEFAULT
Intensity| Intensity 0-100%| 1%| 0%
Color Temperature| CCT 2400 – 8500K| 100K| 6000K
Green Shift| GRN -100% to +100%| 1%| Neutral
INT COLOR SAT MODE

PARAMETER| VALUE| RESOLUTION| DEFAULT
Intensity| Intensity 0-100%| 1%| 0%
Color| Virtual Color 1, 2, 3, 4…| Single Color|
Saturation| Sat 0 – 100%| 1%| 100%
MANUAL CONTROL MODE

DMX CHANNEL FUNCTIONS

ELATION KL FRESNEL 8 FC PO

Supports Software Versions: 1.0.1
Dimmer 1CH| Dimmer Color 6CH| Standard 11CH| Extended 18CH| CMY 9CH| AMY Extended 14CH| DMX Values| Function
1| 1| 1| 1| 1| 1| 000 – 255| Dimmer, 0 to 100%
| 2| 2| 2| 2| 2| 000 – 255| Dimmer Fine
| 3| 3| 3| 3| 3| | Shutter
000 – 031| Shutter closed
032 – 063| No function (shutter open)
064 – 095| Strobe effect, slow to fast
096 – 127| No function (shutter open)
128 – 159| Pulse effect in sequences
160 – 191| No function (shutter open)
192 – 223| Random strobe effect, slow to fast
224 – 255| No function (shutter open)
| | | | 4| 4| 000 – 255| Cyan, 0 to 100%
| | | | | 5| 000 – 256| Cyan Fine
| | | | 5| 6| 000 – 255| Magenta, 0 to 100%
| | | | | 7| 000 – 255| Magenta Fine
| | | | 6| 8| 000 – 255| Yellow, 0 to 100%
| | | | | 9| 000 – 255| Yellow Fine
| | 4| 4| | | 000 – 255| Red, 0 to 100%
| | | 5| | | 000 – 255| Red Fine
| | 5| 6| | | 000 – 255| Green, 0 to 100%
| | | 7| | | 000 – 255| Green Fine
| | 6| 8| | | 000 – 255| Blue, 0 to 100%
| | | 9| | | 000 – 255| Blue Fine
| | 7| 10| | | 000 – 255| Mint, 0 to 100%
| | | 11| | | 000 – 255| Mint Fine
| | 8| 12| | | 000 – 255| Amber, 0 to 100%
| | | 13| | | 000 – 255| Amber Fine
| 4| 9| 14| 7| 10| | CTO
000 – 023| Open
024 – 085| CTO 2400K – 8500K (see Color Temperature Chart )
086 – 255| 8500K
CONTINUED ON NEXT PAGE
ELATION KL FRESNEL 8 FC PO

Supports Software Versions: 1.0.1
Dimmer 1CH| Dimmer Color 6CH| Standard 11CH| Extended 18CH| CMY 9CH| CMY Extended 14CH| DMX Values| Function
| 5| 10| 15| 8| 11| | Color Wheel
000| Open
001 – 179| Virtual Swatch Book (see Color Mac- ros Chart )
| Color Scroll
180 – 201| Clockwise, fast to slow
202 – 207| Stop
208 – 229| Counter-clockwise, slow to fast
230 – 234| Open
| Random Slots
235 – 239| Fast
240 – 244| Medium
245 – 249| Slow
250 – 255| Open
| | | 16| | 12| | Green Shift
000| Idle
001 – 127| Full Minus Green to Neutral
128| Neutral White
129 – 255| Neutral to Full Plus Green
| | | 17| | 13| | Dim Modes
000 – 020| Standard
021 – 040| Stage
041 – 060| TV
061 – 080| Architectural
081 – 100| Theatre
101 – 120| Stage 2
| Dimmer Delay Time
121| 0s
122| 0.1s
123| 0.2s
124| 0.3s
125| 0.4s
126| 0.5s
CONTINUED ON NEXT PAGE
ELATION KL FRESNEL 8 FC PO

Supports Software Versions: 1.0.1
Dimmer 1CH| Dimmer Color 6CH| Standard 11CH| Extended 18CH| CMY 9CH| CMY Extended 14CH| DMX Values| Function
| | | 17| | 13| | Dimmer Delay Time (continued)
127| 0.6s
128| 0.7s
129| 0.8s
130| 0.9s
131| 1.0s
132| 1.5s
133| 2.0s
134| 3.0s
135| 4.0s
136| 5.0s
137| 6.0s
138| 7.0s
139| 8.0s
140| 9.0s
141| 10s
142 – 255| Idle
| 6| 11| 18| 9| 14| | Control
000 – 029| Idle
030 – 039| Fan Mode Auto
040 – 049| Fan Mode Silent
050 – 059| Fan Mode High
060 – 099| Idle
| Refresh Rate (Hz)
100| 900
101| 910
102| 920
103| 930
104| 940
105| 950
106| 960
107| 970
CONTINUED ON NEXT PAGE
ELATION KL FRESNEL 8 FC PO

Supports Software Versions: 1.0.1
Dimmer 1CH| Dimmer Color 6CH| Standard 11CH| Extended 18CH| CMY 9CH| CMY Extended 14CH| DMX Values| Function
| 6| 11| 18| 9| 14| | Refresh Rate (Hz) (continued)
108| 980
109| 990
110| 1000
111| 1010
112| 1020
113| 1030
114| 1040
115| 1050
116| 1060
117| 1070
118| 1080
119| 1090
120| 1100
121| 1110
122| 1120
123| 1130
124| 1140
125| 1150
126| 1160
127| 1170
128| 1180
129| 1190
130| 1200
131| 1210
132| 1220
133| 1230
134| 1240
135| 1250
136| 1260
137| 1270
138| 1280
139| 1290
CONTINUED ON NEXT PAGE
ELATION KL FRESNEL 8 FC PO

6

|

11

|

18

|

9

|

14

| | Refresh Rate (Hz) (continued)
140| 1300
141| 1310
142| 1320
143| 1330
144| 1340
145| 1350
146| 1360
147| 1370
148| 1380
149| 1390
150| 1400
151| 1410
152| 1420
153| 1430
154| 1440
155| 1450
156| 1460
157| 1470
158| 1480
159| 1490
160| 1500
161| 2500
162| 4000
163| 5000
164| 6000
165| 10000
166| 15000
167| 20000
168| 25000
169 – 200| Idle
CONTINUED ON NEXT PAGE
ELATION KL FRESNEL 8 FC PO

DIMMER MODES & CURVES

ELATION KL Fresnel 8 P.O. FC LED lens headlight - 6

COLOR TEMPERATURE CHART

DMX VALUE| COLOR TEMPERATURE (K)| DMX VALUE| COLOR TEMPERATURE (K)
---|---|---|---
024| 2400| 055| 5500
025| 2500| 056| 5600
026| 2600| 057| 5700
027| 2700| 058| 5800
028| 2800| 059| 5900
029| 2900| 060| 6000
030| 3000| 061| 6100
031| 3100| 062| 6200
032| 3200| 063| 6300
033| 3300| 064| 6400
034| 3400| 065| 6500
035| 3500| 066| 6600
036| 3600| 067| 6700
037| 3700| 068| 6800
038| 3800| 069| 6900
039| 3900| 070| 7000
040| 4000| 071| 7100
041| 4100| 072| 7200
042| 4200| 073| 7300
043| 4300| 074| 7400
044| 4400| 075| 7500
045| 4500| 076| 7600
046| 4600| 077| 7700
047| 4700| 078| 7800
048| 4800| 079| 7900
049| 4900| 080| 8000
050| 5000| 081| 8100
051| 5100| 082| 8200
052| 5200| 083| 8300
053| 5300| 084| 8400
054| 5400| 085| 8500

COLOR MACROS CHART

DMX Values| Filter Number| Name| DMX Values| Filter Number| Name
---|---|---|---|---|---
1| 7| Pale Yellow| 28| 113| Magenta
2| 103| Straw| 29| 46| Dark Ma. enta
3| 151| Gold Tint| 30| 48| Rose Purple
4| 100| Spring Yellow| 31| 126| Mauve
5| 10| Medium
Yellow| 32| | Medium Purple
6| 101| Yellow| 33| | Lavender
7| 104| Deep Amber| 34| | Palace Blue
8| 15| Deep Straw| 35| 1124111| Dark Blue
9| 179| Lov ing Amber| 36| IIII| Medium Blue
10| | Gold Amber| 37| 120| Deep Blue
11| | Orange| 38| | Daylight Blue
12| | Deep Orange| 39| 161| Slate Blue
13| | Dark Amber| 40| | Light Blue
14| | Millennium Gold| 41| | Sky Blue
15| 135| Deep Golden
Amber| 42| | Pale Navy Blue
16| | Scarlet| 43| | Marine Blue
17| 106| Primary Red| 44| 115| Peacock Blue
18| up 2€4.1| Bright Red| 45| 172| Lagoon Blue
19| 27| Medium Red| 46| 116| Medium Blue Green
20| 19| Fire| 47| 90| Dark Yellow Green
21| 157| Pink| 48| 139| Primary Green
22| 36| Medium Pink| 49| 1| Fern Green
23| | Dark Pink| 50| 89| Moss Green
24| 128| Bright Pink| 51| 124| Dark Green
25| 148| Bright Rose| 52| 88| Lime Green
26| 332| Special Rose Pink| 53| 138| Pale Green
27| 793| Vanity Fair| 54-179| | No function

DIMENSIONAL DRAWINGS

ELATION KL Fresnel 8 P.O. FC LED lens headlight - 7

SPECIFICATIONS

SOURCE
6500K RGBMA LED Engine
50,000 Hour Average LED Life
May vary depending on several factors including but not limited to:
Environmental Conditions, Power/Voltage, Usage Patterns (On-Off Cycling),
Control and Dimming.| PHOTOMETRIC DATA
18,000+ Total Lumen Output
CRI 92
TLCI 95
Zoom Range 10° – 50°
Beam Angle 10.5° – 49.9°
Field Angle 21° – 66.6°
---|---
EFFECTS
Pole-Operated Pan, Tilt, Zoom
Electronic Dimmer and Strobe
Variable 16-bit Dimming Modes and Curves| COLOR
RGBMA Color Array
CMY Emulation
Variable CCT 2,400K – 8,500K
Green/Magenta Shift
Virtual Gel Swatch Book
CONTROL / CONNECTIONS
6 DMX Channel Modes (1 to 18 channels)
Manual and DMX Controlled Dimmer, Color and Zoom
Dual Rotary Dials
4 Button Control Panel, LED Display
RDM (Remote Device Management)
3/5pin DMX and IP65 Locking Power In/Out Connection| SIZE / WEIGHT
Length: 15.1” (383.5mm)
Width: 13.2” (334.85mm)
Vertical Height: 19.6” (498mm)
Weight: 28.6 lbs. (13kg)
ELECTRICAL / THERMAL
AC 100-240V – 50/60Hz
522W Max Power Consumption
5°F to 113°F (-15°C to 45°C)| INCLUDED ITEMS
Gel Frame and Rotating 8-leaf Barn Doors
Junior Pin (1 1/8” – 28mm)
IP65 Locking Power Cable
APPROVALS / RATINGS
(pending) CE | cETLus | IP20