Neomounts DS60-425WH2 Monitor Desk Mount Instruction Manual
- June 13, 2024
- Neomounts
Table of Contents
Neomounts DS60-425WH2 Monitor Desk Mount
Product Information
The product is a DS60-425WH2 mount, designed to securely hold and position a screen or monitor. It is suitable for screens with VESA hole patterns of 75x75mm and 100x100mm. The mount can support a weight range of 0-8 kg (0-17.6 lbs) and has an adjustable height range of 29.5-60.7 cm.
The package includes the following parts:
- A Clamp (x1)
- B Grommet (x1)
- C (x1)
- D (x2)
- E (x2)
- F (x2)
- G (x1)
- H (x1)
- I (x1)
- J (x1)
- K (x1)
- L M6x16 (x3)
- M 4mm (x1)
- N 6mm (x1)
- M-A M4x12 (x8)
- M-B M5x12 (x8)
- M-C D5 (x8)
DIMENSIONS
PARTS
Installation Instructions
- Mount the clamp to the rod and install to the desk
STEP 1 A Clamp
STEP 1 B Grommet
- Mount the grommet to the rod and install through the Tape measure.
STEP 2
- Assemble the arms and attach them to the rod.
STEP 3
- Screw 2 bolts in the upper 2 VESA holes of the screen, leaving 3 mm spacing.
STEP 4
- Slide the bolts into the top holes of the VESA plate and tighten the bolts. Attach the other 2 bolts in the lower part of the VESA plate.
STEP 5
- Remove the cable cover and run the cable(s) through the cover.
STEP 6
- Adjust the mount to the desired position.
STEP 7
- Adjust the torque and insert the Allen keys into the slot for future use.
Note: If the display does not stop at your desired position, tighten the screw as shown.
CAUTION
- To ensure safety, please read this manual carefully before installation and follow the instructions. Store this manual in a secure place for future reference.
- The manufacturer shall not be legally responsible for any equipment damage or personal injury caused by incorrect installation or operation other than that covered in this manual.
- The mount is designed for easy installation and removal. The manufacturer shall not be liable for damage to equipment or personal injuries arising out of human factors or acts of nature, such as earthquake or typhoon.
- It is recommended that the mount be installed by qualified personnel only.
- At least two persons are needed to install or remove the product to avoid hazard of falling objects.
- Please carefully inspect the area where the mount is to be installed:
- Avoid places that are subject to high temperatures, humidity or contact with water.
- Do not install the product near air conditioning vents or areas with excess dust and fumes.
- Only install on vertical walls and avoid slanted surfaces.
- Do not install in places subject to any shock or vibration.
- Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when viewing the display panel.
- Maintain sufficient space around the display to ensure adequate ventilation.
- To ensure safe installation, first check the structure of the wall, ceiling or floor and select a secure mounting location.
- The wall, ceiling or floor should be strong enough to sustain a weight of at least four times of the display and mount combined. The mounting location must be able to withstand earhquake or other strong shock.
- Do not modify any accessories or use broken parts. Contact your dealer with any questions.
- Tighten all screws (do not exert excessive force to avoid breaking the screw or damaging its thread).
- Drill holes and bolts will be left in the wall, ceiling or floor once the display and bracket are removed. Stains may occur after extended use.
- Since the manufacturer has no way to control the wall, ceiling or floor type and installation of the mount, the warranty of the product shall only cover the body of the mount. The warranty period of the product is 5 years.
- Please consult the English language manual for any dispute on conditions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>