AOC A2272PW4T SMART All in One 22 Inch Screen LED Lit Monitor User Manual

: June 13, 2024
: AOC

Table of Contents

AOC A2272PW4T SMART All in One 22 Inch Screen LED Lit Monitor
Product Information
Product Usage Instructions
Technical Support (FAQ)
Appendix
SAFETY
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AOC A2272PW4T SMART All in One 22 Inch Screen LED Lit Monitor

Product Information

The SMART All-in-One is a versatile device that combines a monitor, computer, and touchscreen functionality. It is available in two models: A2272PW4T and A2472PW4T. This product i manufactured by AOC, a leading brand in the electronics industry.

For detailed information and support, please refer to the user manual provided in the links below:

Product Usage Instructions

Safety
Before using the SMART All-in-One, please read the safety instructions provided in the user manual. These instructions are essential for ensuring proper usage and preventing any potential hazards.

Setup
To set up the SMART All-in-One, follow the instructions provided in the user manual under the “Setup” section. It will guide you through the process of connecting the device and preparing it for use.

Setting up the USB keyboard
If you are using a USB keyboard with the SMART All-in-One, please refer to the user manual’s “Setting up the USB keyboard” section for step-by-step instructions on connecting and configuring the keyboard.

Adjusting
The user manual’s “Adjusting” section provides detailed instructions on how to adjust various settings of the SMART All-in-One. This includes adjusting the display settings, audio settings, and other customizable options.

Operating Instructions
The “Operating Instructions” section of the user manual covers important aspects of using the SMART All-in-One. It includes information on hotkeys and the on-screen display (OSD) settings. Familiarize yourself with these instructions to make the most out of your device.

Hotkeys
Refer to the user manual’s “Hotkeys” section to learn about the various hotkeys available on the SMART All-in-One. These hotkeys allow you to quickly access specific functions and features.

OSD Setting
The OSD Setting section provides instructions on how to navigate and customize the on-screen display (OSD) of the SMART All-in-One. This allows you to adjust settings such as brightness, contrast, color, and more.

Starting with Android
If you intend to use the SMART All-in-One with an Android operating system, the user manual’s “Starting with Android” section will guide you through the setup process and provide instructions on using Android-specific features.

Driver
The user manual’s “Driver” section provides information on installing and updating drivers for the SMART All-in-One. Follow these instructions to ensure compatibility and optimal performance.

i-Menu
The i-Menu feature, explained in the user manual’s “i-Menu” section, allows you to access and adjust various monitor settings using your computer. Refer to this section for detailed instructions on utilizing this functionality.

e-Saver
e-Saver is a power-saving feature of the SMART All-in-One. The user manual’s “e-Saver” section explains how to configure and use this feature effectively to conserve energy.

Screen+
Screen+ is a multitasking feature that allows you to divide the screen into multiple windows. The user manual’s “Screen+” section provides instructions on how to utilize this feature and increase productivity.

Technical Support (FAQ)

If you encounter any issues or have questions about the SMART All-in-One, refer to the user manual’s “Technical Support (FAQ)” section. It contains troubleshooting tips and answers to commonly asked questions.

Troubleshoot
The “Troubleshoot” subsection of the FAQ provides solutions for common problems you may encounter while using the SMART All-in-One. Follow the instructions provided to resolve any issues effectively.

Error Message & Possible Solution
Refer to the “Error Message & Possible Solution” subsection of the FAQ for information on specific error messages that may appear on the SMART All-in- One’s screen. The user manual provides possible solutions to address these errors.

No Signal
If you see a “No Signal” message on the screen, follow the instructions in the user manual’s “No Signal” subsection to troubleshoot and resolve this issue.

Input Not Support
If you encounter an “Input Not Support” message, the user manual’s “Input Not Support” subsection will guide you through the necessary steps to rectify this issue and ensure proper input compatibility.

Appendix

The user manual’s “Appendix” section provides additional information and resources related to the SMART All-in-One. It includes details on HDMI connectivity, pin assignments, regulations, and service-related information.

For HDMI
Refer to the user manual’s “For HDMI” subsection for instructions on connecting devices using HDMI cables and optimizing HDMI functionality on the SMART All-in-One.

Pin Assignments
The “Pin Assignments” subsection of the Appendix provides details on the pin assignments for various ports and connectors on the SMART All-in-One. This information can be useful for understanding connectivity options.

Regulation
The “Regulation” section of the user manual contains regulatory information and compliance details related to the SMART All-in-One. Familiarize yourself with this section to ensure adherence to relevant guidelines.

Service
If you require service or assistance with the SMART All-in-One, refer to the user manual’s “Service” section for contact information and instructions on obtaining support.

SMART All-in-One User Manual
A2272PW4T/A2472PW4T

https://manual-hub.com/

www.aoc.com
©2013 AOC.All Rights Reserved.

https://manual-hub.com/

SAFETY

NATIONAL CONVENTIONS
The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your monitor.. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.
4

POWER
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. Unplug the unit during a lightning storm or when it will not be used for long periods of time.This will protect the monitor from damage due to power surges. Do not overload power strips and extension cords. Overloading can result in fire or electric shock. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 19V, 3.42A The wall socket shall be installed near the equipment and shall be easily accessible. For use only with the attached power adapter (Output 19VDC) which have UL, CSA listed license (Only for monitors with power adapter). Manufacturers: 1) TPV ELECTRONICS(FUJIAN) CO., LTD model: ADPC1965 2) SHENZHEN HONOR ELECTRONICS CO., LTD. / model: ADS-65LSI-19-1 19065G
5

INSTALLATION

Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer.A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

Do not place the front of the product on the floor.

If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor.

See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or with the stand:

Installed on the wall

11 7/8 inches 30cm

4 inches 10cm
Installed with stand

4 inches 10cm

Leave at least this space around the set.

11 7/8 inches 30cm

4 inches 10cm

4 inches 10cm
Leave at least this space around the set.

4 inches 10cm

6

CLEANING
Clean the cabinet regularly with cloth.You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product.The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product.
7

OTHER
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation. For display with glossy bezel the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.
8

SETUP
CONTENTS OF THE BOX
1. LCD Monitor 2. CD Manual 3. Power Cord 4. Power Adapter 5. D-SUB Cable 6. Audio Cable 7. USB Cable (upstream) 8. HDMI Cable 9. MHL Cable 10. USB Keyboard 11. USB Mouse
v Not all signal cables (D-SUB,Audio, USB, HDMI, MHL cables) and Keyboard , Mouse will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.

ADJUSTING VIEWING ANGLE
v For optimal viewing, it is recommended to look at the full face of the monitor, and then adjust the monitor’s angle to your own preference.
v Hold the stand so you will not topple the monitor when you change the monitor’s angle. v You are able to adjust the tilted angle to 15°or 57°.

15°

57°

9

v Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
v It is recommended to stabilize with a fixed point in order to lock the stand if the tilted angle is equal to or over 20°.
v Do not adjust the tilted angle less than 20°.The monitor may fall caused by instability. v Pay attention not to bounce back the stand while adjusting the tilted angle.
10

CONNECTING THE MONITOR
Cable connections at the back of monitor:

7 8 9 10

11

12

6

1

5

2

4

3

1. D-SUB Signal Input

Micro USB Port (OTG: only support device function)

2. HDMI/MHL Signal Input

8. USB Port

3. Power Input

9. USB Port

SD Card Slot (SD/SDHC/SDXC/ MMC/MS/MS-Pro)

10. Audio In

5. USB Port

11. Earphone Out

6. RJ45 (10/100Mbps)

12. Kensington Lock

To protect equipment, always turn off the PC and monitor before connecting.
1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other
end to the computer’s D-Sub port. 3. Optional (Requires a video card with HDMI port) Connect one end of the HDMI cable to
the back of the monitor and connect the other end to the computer’s HDMI port. 4. Turn on your monitor and computer. 5. Video content supporting resolution:VGA / HDMI: 1920 x 1080/60Hz (Maximum). 6. If you want to connect monitor and PC by micro USB, please install Android driver in PC
(Android Driver save in CD).
If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting on page 51.

11

USING “MHL(MOBILE HIGH-DEFINITION LINK)”
“MHL” (Mobile High-Definition Link)
This feature allows you to enjoy videos and photos (imported from a connected mobile device that supports MHL) on the screenof the product.
v To use the MHL function, you need an MHL-certified mobile device.You can check if your mobile device is MHL certified on the device manufacturer’s website.To find a list of MHLcertified devices, visit the official MHL website (http://www.mhlconsortium.org).
v To use the MHL function, the latest version of software must be installed on the mobile device. v On some mobile devices, the MHL function may not be available depending on the device’s
performance or functionality. v Since the display size of the product is larger than those of mobile devices, the picture quality
may degrade. v This product is officially MHL-certified. If you encounter any problem when using the MHL
function, please contact the manufacturer of the mobile device. v The picture quality may degrade when content (imported from the mobile device) with a low
Resolution is played on the product.
Using “MHL”
1. Connect the micro USB port on the mobile device to the [HDMI / MHL] port on the product using the MHL cable.

v When the MHL cable is used, [HDMI / MHL] is the only port on this monitor that supports the MHL function.
v Mobile device must be purchased separately. 2. Connect the DC power adapter to the product and a power outlet.

3. Press the source button

and switch to HDMI /MHL to activate MHL mode.

4. After about 3 seconds, the MHL screen will be displayed if MHL mode is active. Remark:The indicated time “3 sec later” may vary depending on the mobile device.

When the mobile device is not connected or does not support MHL

v l If MHL mode is not activated, check the connection of the mobile device. v l If MHL mode is not activated, check if the mobile device supports MHL. v l If MHL mode is not activated even though the mobile device supports MHL, update the
12

firmware of the mobile device to the latest version. v If MHL mode is not activated even though the mobile device supports MHL, check if mobile
device MHL port is MHL standard port otherwise an additional MHL-enabled adapter is required.
13

MULTI-TOUCH SCREEN
User can use Display Multi-touch(2 points) Function under Android system.While you under XP, win7, win8 system, before using Display Multi-touch(2 points) Function, user need to connect basic wires ( power cable,VGA cable, USB cable).Then user can fully enjoy Multi-touch (2 points) Function. Part of specific use, please see the following drawings.
14

CONNECTING USB KEYBOARD & MOUSE
To use this monitor for Android system, you need to connect USB keyboard/mouse to the USB port at the back of monitor: To use this monitor as a normal monitor for D-SUB and HDMI input controlled by the same USB keyboard/mouse connected to the USB port at the back of monitor, you need to connect a B-type USB cable from this monitor to your PC.
PC USB Keyboard/Mouse Setting up the USB keyboard
For the first time using this monitor, you will be prompted to do the USB keyboard settings. Please check the box “Use USB Keyboad”. Click “Select keyboard” button to enter keyboard type setting.
15

Select default keyboard type and back to OOBE page. Press “Next” button to complete keyboard setting.
16

ADJUSTING
SETTING OPTIMAL RESOLUTION
Windows Vista
1. Click START. 2. Click CONTROL PANEL.
3. Click Appearance and Personalization.
4. Click Personalization.
17

5. Click Display Settings. 6. Set the resolution SLIDE-BAR to 1920 x 1080.
Windows 8
1. Right click and click All apps at the bottom-right of the screen.
2. Set the “View by” to “Category”.
18

3. Click Appearance and Personalization.
4. Click DISPLAY.
5. Set the resolution SLIDE-BAR to 1920 x 1080.
Windows ME/2000
1. Click START. 2. Click SETTINGS. 3. Click CONTROL PANEL. 4. Double click DISPLAY. 5. Click SETTINGS. 6. Set the resolution SLIDE-BAR to 1920 x 1080.
19

OPERATING INSTRUCTIONS
HOTKEYS
v Connect the power cord and the video cable. v Press the POWER key to turn on the monitor.The power indicator will light up.
8 76

5432 1

POWER

MENU / ENTER

For menu control 5. 6.

SOURCE / AUTO / EXIT 1.0 Megapixel Webcam

+ / VOLUME

Webcam activity light

/ CLEAR VISION

Microphone

v Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
v Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor.
v For maximum protection, repackage your monitor as it was originally packed at the factory. v To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be
removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet.As a safety precaution, always unplug the monitor before cleaning it. v Do not scratch the screen with hard things, it may cause permanent damage. v Don’t leak liquid into monitor which will result in the damage of component.

20

OSD SETTING
Basic and simple instruction on the control keys.

Luminance

Image Setup

Color Setup

Picture Boost

OSD Setup

Extra

Exit

Contrast Brightness Eco mode

50 50 Standard

Gamma DCR Overdrive

Gamma 1 Off Off

1. Press button to display the control menu. 2. Press or button to navigate through the menu items. Once the desired item is highlighted,
press button to activate it. If there is a sub-menu, press or button to navigate through the sub-menu functions. 3. Press or button to change the settings of the selected function. Press button to exit. If you want to adjust any other function, repeat steps 2~3.
v If there is only one signal input, the item “Input Select” is disabled. v If the screen size is 4:3, or the input signal resolution is “Native”, the item of “Image Ratio” is
disabled. v If one of the DCR, Color Boost, or Picture Boost function is activated; the other two are turned
off accordingly.

21

Luminance

Image Setup

Color Setup

Picture Boost

OSD Setup

Extra

Exit

Contrast Brightness Eco mode

50 50 Standard

Gamma DCR Overdrive

Gamma 1 Off Off

1. Press button to display menu. 2. Press or button to select (Luminance), and press button to enter.

3. Press or button to select submenu, and press 4. Press or button to adjust. 5. Press button to exit.

button to enter.

Main Menu

Sub Menu Item Brightness Contrast

0~100 0~100
Standard

Description Backlight Adjustment. Contrast from Digital-register.
Standard Mode.

Text

Text Mode.

Luminance Eco mode

Internet Game

Internet Mode. Game Mode.

Movie

Movie Mode.

Gamma

DCR

Overdrive

Weak Medium Strong Off

Spor ts
Gamma 1 Gamma 2 Gamma 3 Off
On

Sports Mode.
Adjust to Gamma 1. Adjust to Gamma 2. Adjust to Gamma 3. Disable dynamic contrast ratio.
Enable dynamic contrast ratio.

22

Image Setup

Image Setup Clock Phase Sharpness

Color Setup 50 50 50

Picture Boost

OSD Setup

H. Position V. Position

Extra 50 50

Exit

Luminance

1. Press button to display menu.

2. Press or button to select

(Image Setup), and press button to enter.

3. Press or button to select submenu, and press 4. Press or button to adjust. 5. Press button to exit.

button to enter.

Main Menu Image Setup

Sub Menu Item Clock Phase Sharpness H.Position V.Position

0~100 0~100 0~100 0~100 0~100

Description Adjust picture Clock to reduce Vertical-Line noise. Adjust Picture Phase to reduce Horizontal-Line noise. Adjust picture sharpness. Adjust the horizontal position of the picture. Adjust the vertical position of the picture.

23

Color Setup

Color Setup Color Temp. DCB Mode DCB Demo

Picture Boost Warm Off Off

OSD Setup Red Green Blue

Extra

Exit 50 50 50

Luminance

Image Setup

1. Press button to display menu. 2. Press or button to select (Color Setup), and press

button to enter.

3. Press or button to select submenu, and press 4. Press or button to adjust. 5. Press button to exit.

button to enter.

Main Menu Color Setup

Sub Menu Item Color Setup
DCB Mode DCB Demo

Warm
Normal
Cool
sRGB
User
Full Enhance Nature Skin Green Field Sky-blue AutoDetect

Red Green Blue on or off on or off on or off on or off on or off on or off

Description Recall Warm Color Temperature from EEPROM. Recall Normal Color Temperature from EEPROM. Recall Cool Color Temperature from EEPROM. Recall SRGB Color Temperature from EEPROM. Red Gain from Digital-register. Green Gain Digital-register. Blue Gain from Digital-register. Disable or Enable Full Enhance Mode. Disable or Enable Nature Skin Mode. Disable or Enable Green Field Mode. Disable or Enable Sky-blue Mode. Disable or Enable AutoDetect Mode. Disable or Enable Demo.

24

Picture Boost

Picture Boost Bright Frame Frame Size

OSD Setup Off 50

Extra

Exit

Brightness Contrast

Luminance

Image Setup

50

H. Position

50

V. Position

Color Setup 50 50

1. Press button to display menu. 2. Press or button to select

(Picture Boost), and press

button to enter.

3. Press or button to select submenu, and press 4. Press or button to adjust. 5. Press button to exit.

button to enter.

Main Menu Picture Boost

Sub Menu Item Frame Size Brightness Contrast H. position V. position Bright Frame

14~100 0~100 0~100 0~100 0~100 on or off

Description Adjust Frame Size. Adjust Frame Brightness. Adjust Frame Contrast. Adjust Frame horizontal position. Adjust Frame vertical position. Disable or Enable Bright Frame.

25

OSD Setup

OSD Setup Language Timeout S.Power On Sync

Extra English 120 Off

Exit

Luminance

H. Position V. Position

Image Setup

Color Setup

50

Transparence

0

Break Reminder

Picture Boost 25
Off

1. Press button to display menu. 2. Press or button to select

(OSD Setup), and press

button to enter.

3. Press or button to select submenu, and press 4. Press or button to adjust. 5. Press button to exit.

button to enter.

Main Menu OSD Setup

Sub Menu Item H. Position V. Position Timeout Transparence Language
S.Power On Sync

0~100 0~100 5~120 0~100
OFF(default)
ON

Description Adjust the horizontal position of OSD. Adjust the vertical position of OSD. Adjust the OSD Timeout. Adjust the transparence of OSD. Select the OSD language. Android will not be on if the previous off mode is D-Sub or HDMI. While android is on, android mode keep on, even user change to D-Sub or HDMI mode, to prevent system be turned on again. Android will always on no matter the previous mode is. While android is on, android mode keep on, even user change to D-Sub or HDMI mode, to prevent system be turned on again.

26

Extra

Extra Input Select Auto Config. Off Timer

Exit Auto Yes 00

Luminance

Image Setup

Image Ratio

4 : 3

DDC/CI

Yes

Reset

No

Color Setup

Picture Boost

OSD Setup

Resolution : 1024(H)X768(V) H. Frequency : 60KHz V. Frequency : 60Hz

1. Press button to display menu. 2. Press or button to select

(Extra), and press

button to enter.

3. Press or button to select submenu, and press 4. Press or button to adjust. 5. Press button to exit.

button to enter.

Main Menu Extra

Sub Menu Item
Input Select
Auto Config. Off timer Image Ratio DDC-CI Reset Information

Auto/D-Sub/ HDMI/ Android yes or no 0~24 hrs wide or 4:3 yes or no yes or no

Description
Select input signal source.
Auto adjust the picture to default. Select DC off time. Select wide or 4:3 format for display. Turn ON/OFF DDC-CI Support. Reset the menu to default. Show the information of the main image and subimage source.

27

Exit
Exit

Luminance

Image Setup

Color Setup

Picture Boost

OSD Setup

Extra

1. Press button to display menu. 2. Press or button to select (Exit), and press

button to enter.

Main Menu Exit

Sub Menu Item

Exit

Exit the main OSD.

Description

LED INDICATOR

Status Full Power Mode Power Saving Mode Active-off Mode

LED Color White Red Off

28

STARTING WITH ANDROID
This Smart Monitor is embedded with Android operating system, that it can work individually without connecting a PC. 1. Press button to display the source list. 2. Select [Android] and press button to confirm the selection. 3. Press button to display the selections.
D-SUB HDMI/MHL
Android

The descriptions for function control:

Icon (PPHMF

Description Shortcut for Google Search

Back to previous page

Back to Android Home Screen

Display recently used application

Application Gallery Notification / Local Time / Settings

29

CUSTOMIZING YOUR HOME SCREEN
Adding application icons, shortcuts, or widgets to the home screen as your preference.You can also change the wallpaper.
v Add an item to the Home Screen:

1. Click on the

icon to view the application gallery.

2. Select [APPS] or [WIDGETS]. 3. Click and hold the item until it enlarged. Drag the item to the place you preferred on the
Home Screen.

v Move an item on the Home Screen:
1. Click and hold the item until it enlarged. 2. Drag the item to the place you preferred on the Home Screen.

v Remove an item from the Home Screen: 1. Click and hold the item until it enlarged.The Trash Can icon displayed. 2. Drag the item to the Trash Can icon to remove the item from the Home Screen.

VIEWING THE APPS GALLERY

1. Click on the

icon to view the applications.

2. Click on the application to open it.

3. Click on the

icon to return to the Home Screen, or click on the

return to the previous screen.

icon to

BROWSING THE INTERNET
v Open a webpage:

1. On the Home Screen, click

Browser.

2. Click the URL box at the top of the Browser.The on-screen keyboard displayed. 3. Enter the URL address to open the webpage.

v Set the homepage:

1. Click on the icon at the top-right of the screen when browsing the web.
2. Edit the informations and click [OK] to bookmark this page. 3. Select [Settings] > [General] > [Set homepage] and select the [Current page] to set the
current page as your home page.
v Add to bookmark:
1. Click on the icon at the right of the URL box when browsing the web. 2. Select [BOOKMARKS] > [Add bookmark] to add the current page to your bookmark.

30

USING THE ON-SCREEN KEYBOARD
v Enter text: 1. Click on a text field.The on-screen keyboard opens. 2. Click on the keys to type.

Key

Description

Key

Switch to upper or lower case letters for English input.

Enter a space.

Enter your text..
Single press to go backspace and delete one character. Long press to go backspace and delete whole characters.
Click for input options.

Description Press to enter expression symbol. Long press to select from all expression symbols. Close the on-screen keyboard.
Back to Android Home Screen
Display recently used application
Snap for screen shot

Switch to the symbol keyboard..

Notification / Local Time / Settings

CONNECTING TO NETWORK
v Turn on Wi-Fi and connect to the Wi-Fi network:
1. Click on the at the bottom-right of the screen. Click on the [Settings] to
open the sub-menu. 2. Select [NETWORKS], and check [Wi-Fi] to turn it on. 3. Select [SCAN] to scan for available Wi-Fi networks nearby.The secured networks are
indicated with a lock icon. 4. Touch a network to connect it automatically, or touch [ADD NETWORK] to add new
network manually. 5. If the network is open, touch [Connect] to confirm for connecting to the network on the
prompted window. 6. If the network is secured, enter the password and touch [Connect] on the prompted
window for connecting to the secured network.

31

ADJUSTING THE SETTINGS FOR ANDROID Click on the at the bottom-right of the screen. Click on the [Settings] to open the
sub-menu.

Main Menu

Sub Menu Item

WIRELESS & NETWORKS

Wi-Fi

ON/OFF

Bluetooth

ON/OFF

Ethernet

Ethernet configuration

More DEVICE

VPN Tethering &portable hotspot

Sound
Display Storage Apps

Sound
System
Brigheness Wallpaper Sleep Font size Available spaces Downloaded
On SD card
Running All

Description
Turn on or off the Wi-Fi. Manage the Wi-Fi network. Search and connect to the available networks.
Set the connection type and connect to the available Ethernet. VPN Connection
Tethering &portable hotspot settings
Music,Video,games,&other media Notifications Alarms Default notification sound Touch sounds
Set the sleep timer. Select the preferred font size. View the available storage space. View the downloaded applications. Manage the applications stored on the SD card or internal storage. View the running applications. View all the applications.

32

Main Menu Users PERSONAL Location access
Security
Language & input Backup & reset Accounts Accounts SYSTEM
Date & time
Accessibility
Developer options
About

Sub Menu Item You Other users Add users

Users information Users information Add users

Description

Location access Location sources, Screen security Password
Device administration Credential storage Select language
Personal Data
Backup&Restore

Turn on or off Access to my location
Set the screen lock. Check for displaying the password while entering the password. Allow or not allow installation of apps from unknow sources Display the certificates. Select the display language for your device and set the keyboard settings. Erase all data from your devices, including your Google account, system and application data and settings, and downloaded applications. Back up my data and Automatic restore

Add account

Add an account cCorporateaEmailaGoogle

Automatic data & time
Set date Set time Select time zone Use 24-hour format Select date format Ser vices System Developer options Debugging Input Drawing Monitoring Apps System updates, Status, Legal information, Android version, Kernel version, and Build number.

Check for using the information form the network automatically. Unchecked for entering the information manually. Set the date. Set the time. Select the time zone for current region. Set the time format to 24-hour. Select the preference date format. Display the installed services. Set the allowance for installing web scripts.
View the informations for the device.

33

ANDROID SOFTWARE UPDATE
You can upgrade system by Local update mode.
v Local update support upgrade from SD card device.
v During system update, DONOT pull out SD card device or power off Smart Monitor.
Local update
1. Copy updates file on SD card device. Insert SD card device.The SD card device should not be write-protected, and Smart Monitor can read it.
2. Start system updates as below path: Settings About System updates Local update. Click `Next’ to continue update process.

3. Smart Monitor will show Update file has found! If you want to update, please pressNext’, the System will be reboot. Do not power off !’. Click `Next’ to start system updates. During upgrade, Smart Monitor will reboot and complete system update automatically.

DRIVER

34

MONITOR DRIVER
Windows 8
1. Start Windows® 8 2. Right click and click All apps at the bottom-right of the screen.
3. Click on the “Control panel” icon
35

4. Set the “View by” to “Large icons” or “Small icons”. 5. Click on the “Display” icon.
36

6. Click on the “Change display settings” button. 7. Click the “Advanced Settings” button.
37

8. Click the “Monitor” tab and then click the “Properties” button.
9. Click the “Driver” tab.
38

10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver… ” and then click the “Browse my computer for driver software” button.
11. Select “Let me pick from a list of device drivers on my computer”.
39

12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:Drivermodule name (where X is the drive letter designator for the CD-ROM drive).
13. Select the “xxx.inf” file and click the “Open” button. Click the “OK” button. 14. Select your monitor model and click the “Next” button.The files will be copied from the CD
to your hard disk drive. 15. Close all open windows and remove the CD. 16. Restart the system.The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
Windows 7
1. Start Windows® 7 2. Click on the “Start” button and then click on “Control Panel”.
40

3. Click on the “Display” icon. 4. Click on the “Change display settings” button. 5. Click the”Advanced settings”button.
41

6. Click the “Monitor” tab and then click the “Properties” button. 7. Click the “Driver” tab.
42

8. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver… ” and then click the “Browse my computer for driver software” button.
9. Select “Let me pick from a list of device drivers on my computer”.
43

10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:Drivermodule name (where X is the drive letter designator for the CD-ROM drive).
11. Select the “xxx.inf” file and click the “Open” button. Click the “OK” button. 12. Select your monitor model and click the “Next” button.The files will be copied from the CD
to your hard disk drive. 13. Close all open windows and remove the CD. 14. Restart the system.The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
44

Windows Vista
1. Click “Start” and “Control Panel”.Then, double-click on “Appearance and Personalization”.
2. Click “Personalization” and then “Display Settings”.
3. Click “Advanced Settings…”.
45

4. Click “Properties” in the “Monitor” tab. If the “Properties” button is deactivated, it means the configuration for your monitor is completed.The monitor can be used as is. If the message “Windows needs…” is displayed, as shown in the figure below, click “Continue”.
5. Click “Update Driver…” in the “Driver” tab.
6. Check the “Browse my computer for driver software” checkbox and click “Let me pick from a list of device drivers on my computer”.
7. Click on the “Have disk…” button, then click on the “Browse…” button and then select the appropriate drive F:Driver (CD-ROM Drive).
46

8. Select your monitor model and click on the “Next” button. 9. Click “Close” “Close” “OK” “OK” on the following screens displayed in sequence.
Windows 2000
1. Start Windows® 2000. 2. Click on the “Start” button, point to “Settings”, and then click on “Control Panel”. 3. Double click on the “Display” icon. 4. Select the “Settings” tab then click on “Advanced…”. 5. Select “Monitor”.
– If the “Properties” button is inactive, it means your monitor is properly configured. Please stop installation. – If the “Properties” button is active. Click on “Properties” button. Please follow the steps given below. 6. Click on “Driver” and then click on “Update Driver…” then click on the “Next” button. 7. Select “Display a list of the known drivers for this device so that I can choose a specific driver”, then click on “Next” and then click on “Have disk…”. 8. Click on the “Browse…” button then select the appropriate drive F: (CD-ROM Drive). 9. Click on the “Open” button, then click on the “OK” button. 10. Select your monitor model and click on the “Next” button. 11. Click on the “Finish” button then the “Close” button. If you can see the “Digital Signature Not Found” window, click on the “Yes” button.
Windows ME
1. Start Windows® ME. 2. Click on the “Start” button, point to “Settings”, and then click on “Control Panel”. 3. Double click on the “Display” icon. 4. Select the “Settings” tab then click on “Advanced…”. 5. Select the “Monitor” button, then click on “Change…” button. 6. Select “Specify the location of the driver (Advanced)” and click on the “Next” button. 7. Select “Display a list of all the drivers in a specific location, so you can choose the
driver you want”, then click on “Next” and then click on “Have Disk…”. 8. Click on the “Browse…” button, select the appropriate drive F: (CD-ROM Drive) then click on
the “OK” button. 9. Click on the “OK” button, select your monitor model and click on the “Next” button. 10. Click on “Finish” button then the “Close” button.
47

I-MENU
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor.To complete installation, please follow the installation guide.
48

E-SAVER
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below). Please click on “driver/e-Saver/setup.exe” to start installing the e-Saver software, follow the install wizard to complete software installation. Under each of the four PC statuses, you may choose the desired time (in minutes) from the pulldown menu for your monitor to automatically shutdown.The example below illustrated: 1. The monitor will never shutdown when the PC is powered on. 2. The monitor will automatically shutdown 5 minutes after the PC is powered off. 3. The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode. 4. The monitor will automatically shutdown 20 minutes after the screen saver appears.
You can click “RESET” to set the e-Saver to its default settings like below.
49

SCREEN+
Welcome to “Screen+” software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop into different panels, and each panel displays a different window.You only need to drag the window to a corresponding panel when you want to access it. It supports multiple monitor display to make your task easier. Please follow the installation software to install it.
50

TECHNICAL SUPPORT (FAQ)

TROUBLESHOOT
Problem & Question Power LED is not on
No images on the screen
Picture Is Fuzzy & Has Ghosting Shadowing Problem Picture Bounces, Flickers Or Wave Pattern Appears In The Picture
Monitor Is Stuck In ActiveOff Mode”
Missing one of the primary colors (RED, GREEN, or BLUE)

Possible Solution v Make sure the power button is ON and the Power Cord is
properly connected to a grounded power outlet and to the monitor. v Is the power cord connected properly? Check the power cord connection and power supply. v Is the cable connected correctly? (Connected using the D-sub cable) Check the DB-15 cable connection. (Connected using the HDMI cable) Check the HDMI cable connection. * HDMI input is not available on every model. v If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/2000) and then change the frequency of the video card. (Refer to the Setting the Optimal Resolution) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer. v Can you see “Input Not Supported” on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. v Make sure the AOC Monitor Drivers are installed. v Adjust the Contrast and Brightness Controls. v Press to auto adjust. v Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back. v Move electrical devices that may cause electrical interference as far away from the monitor as possible. v Use the maximum refresh rate your monitor is capable of at the resolution you are using. v The Computer Power Switch should be in the ON position. v The Computer Video Card should be snugly fitted in its slot. v Make sure the monitor’s video cable is properly connected to the computer. v Inspect the monitor’s video cable and make sure no pin is bent. v Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED.The LED should either turn ON or OFF after hitting the CAPS LOCK key. v Inspect the monitor’s video cable and make sure that no pin is damaged. v Make sure the monitor’s video cable is properly connected to the computer.

51

Problem & Question Screen image is not centered or sized properly Picture has color defects (white does not look white)
Horizontal or vertical disturbances on the screen

Possible Solution v Adjust H-Position and V-Position or press hot-key (AUTO).
v Adjust RGB color or select desired color temperature. v Use Windows 95/98/2000/ME shut-down mode to adjust
CLOCK and PHASE. v Press to auto-adjust.

CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. PHASE adjusts the phase of the pixel clock signal.With a wrong phase adjustment the picture has horizontal disturbances in light picture. For PHASE and CLOCK adjustment use “dot- pattern” or Windows XP/VISTA/7 shut-down mode pattern.
ERROR MESSAGE & POSSIBLE SOLUTION
No Signal
1. Check that the signal-cable is properly connected. If the connector is loose, tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
Input Not Support
Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table on page 34.

52

APPENDIX
PLUG AND PLAY
Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol.The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY,THERE MUST BE A VIDEO INPUT SIGNAL. This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA) and The Swedish Confederation Employees (NUTEK).This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present.When there is no video input signal this monitor, following a time-out period, will automatically switch to an Standby mode.This reduces the monitor’s internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn.The appearance is similar to a “Screen Saver” feature except the display is completely off.The display is restored by pressing a key on the keyboard, or clicking the mouse.
KEYBOARD AND MOUSE
86 Key Spanish
85 Key English
53

KVM BEHAVIOR
Android Interface This monitor is equipped with USB MTT Hub Controller which is premium 4-port hub solution which fully complies with Universal Serial Bus Specification Revision 2.0. that provide dedicated TT* to each downstream (DS) ports, which guarantee Full-Speed(FS) data passing bandwidth when multiple FS device perform heavy loading operations. One Webcam port and One Touch Panel Port are dedicated for system usage. IO Interface USB 2.0 x2 to meet the requirement with minimum effort.
UI Interface define / {} Developer options / Stay Awake would be stay awake , otherwise system would mute the screen after USB device wake up event. VGA/ HDMI Interface USB Hub device supports PC during “sleep” and “power-off” wake up event but not support both Smart Monitor DC Off / PC suspend then PC wake up event.
54

Part of the keys are not compatible with Windows OS and Android OS, please refer to the table below:

Keys

OS

Windows OS

Android OS

×

x

55

SPECIFICATIONS
A2272PW4T

LCD Panel

Driving system Size Pixel Pitch

Video

Input
Display Colors Dot Clock Max. Resolution Plug & Play LAN Speed RF Module M/N Built-in Webcam
Power Consumption

Separate Sync. H-Frequency V-Frequency
ON Mode Standby Mode OFF Mode

Input Connector

Input Video Signal Power Source Environmental Considerations Dimensions Weight (N.W.):

21.5″ WLED 54.7cm diagonal 0.24825mm(H) × 0.24825mm(V) R, G, B Analog Interface Digital H/V TTL 30kHz ~ 83kHz 50 ~ 76Hz 16.7M Colors 148.5MHz 1920×1080@60Hz VESA DDC2BTM 10/100Mbps BCM94330LGA 1.0 megapixel camera with microphone and LED indicator 30W (Typ.) d 2W (VGA/HDMI) d 0.5W D-Sub 15pin HDMI 19pin Analog: 0.7Vp-p(standard), 75 OHM, positive or negative HDMI: 0.7Vp-p(standard), 75 OHM, positive or negative 100~240VAC, 50/60Hz Operating Temp.: 0° to 40°C Storage Temp.: -20° to 60°C Operating Humidity: 15% to 90% 561.93(W) x 355(H) x 47.1(D) mm 5.0 kg

56

A2472PW4T
LCD Panel

Driving system Size Pixel Pitch

Video

Input
Display Colors Dot Clock Max. Resolution Plug & Play LAN Speed RF Module M/N Built-in Webcam
Power Consumption

Separate Sync. H-Frequency V-Frequency
ON Mode Standby Mode OFF Mode

Input Connector

Input Video Signal Power Source Environmental Considerations Dimensions Weight (N.W.):

23.6″ WLED 59.8cm diagonal 0.2715mm(H) × 0.2715mm(V) R, G, B Analog Interface Digital H/V TTL 30kHz ~ 83kHz 50 ~ 76Hz 16.7M Colors 148.5MHz 1920×1080@60Hz VESA DDC2BTM 10/100Mbps BCM94330LGA 1.0 megapixel camera with microphone and LED indicator 30W (Typ.) d 2W (VGA/HDMI) d 0.5W D-Sub 15pin HDMI 19pin Analog: 0.7Vp-p(standard), 75 OHM, positive or negative HDMI: 0.7Vp-p(standard), 75 OHM, positive or negative 100~240VAC, 50/60Hz Operating Temp.: 0° to 40°C Storage Temp.: -20° to 60°C Operating Humidity: 15% to 90% 606.73(W) x 379.37(H) x 49.40(D) mm 6.0 kg

57

Touch screen specifications

Touch technology Input Method Touch stylus diameter Resolution Touch accuracy
Operating Systems

Microsoft Windows 8 Microsoft Windows 7 Microsoft Windows Vista Microsoft Windows XP

Infrared Optical Structure Finger, gloved hand, or any other opaque stylus t7 mm 32767 x 32767 < ± 2.5 mm 95% coverage Multi-Touch (2 points) Multi-Touch (2 points)
Single Touch Single Touch+Action

PRESET DISPLAY MODES

STANDARD

RESOLUTION

640×480@60Hz

VGA

640×480@72Hz

640×480@75Hz

HORIZONTAL FREQUENCY (KHz)
31.469
37.861
37.500

VERTICAL FREQUENCY (Hz)
59.940
72.809
75.00

SVGA

800×600@56Hz 800×600@60Hz 800×600@72Hz 800×600@75Hz 1024×768@60Hz

35.156 37.879 48.077 46.875 48.363

56.250 60.317 72.188 75.000 60.004

XGA

1024×768@70Hz 1024×768@75Hz

56.476 60.023

70.069 75.029

SXGA

1280×1024@60Hz 1280×1024@75Hz 1280×960@60Hz

63.981 79.976
60

60.020 75.025
60

WXGA WSXGA WUXGA IBM-MODEDOS

1400×900@60Hz 1680×1050@60Hz 1920×1080@60Hz 720×400@70Hz

55.935 65.29 67.5 31.469

60 59.95 59.934 70.087

58

MAC MODEVGA 640×480@75Hz MAC MODESVGA 832×624@75Hz

35 49.725

66.667 74.551

59

For HDMI
Resolution
480P@60Hz for Digital only 480P@60Hz for Digital only 576P@50Hz for Digital only 720P@50Hz for Digital only 720P@60Hz for Digital only 1080P@50Hz for Digital only 1080P@60Hz for Digital only 1080i@50Hz for Digital only 1080i@60Hz for Digital only

Horizontal Frequency (kHz)
31.469 31.469 31.250 37.500 45.000 56.250 67.500 28.130 33.750

Vertical Frequency (Hz)
59.940 59.940 50.000 50.000 60.000 50.000 60.000 50.000 60.050

Dot Clock (MHz) 25.175 27.000 27.000 74.250 74.250 148.500 148.500 74.250 74.250

60

PIN ASSIGNMENTS

1

5

6

10

11

15

15 – Pin Color Display Signal Cable

PIN NO. 1. 2. 3. 4. 5. 6. 7. 8.

DESCRIPTION Red Green Blue Ground Detect Cable R-Ground G-Ground B-Ground

19 17 15 13 11 9 7 5 3 1 18 16 14 12 10 8 6 4 2

19 – Pin Color Display Signal Cable

PIN NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

DESCRIPTION TMDS Data 2+ TMDS Data 2 Shield TMDS Data 2TMDS data 1+ TMDS data 1 Shield TMDS data 1TMDS data 0+ TMDS data 0 Shield TMDS data 0TMDS data ck+

PIN NO. 9. 10. 11. 12. 13. 14. 15.

DESCRIPTION +5V Ground Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock

PIN NO. 11. 12. 13. 14. 15. 16. 17. 18. 19.

DESCRIPTION TMDS data Shield TMDS data ckCEC N.C DDC SCL DDC CLK DDC/CEC Ground +5 V Power Hot Plug Detect

61

REGULATION
EUROPE
EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: ¢ EN60950-1
Safety of Information Technology Equipment ¢ EN 62311
Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz-300 GHz) ¢ EN 300 328 Electromagnetic compatibility and Radio spectrum Matters (ERM);Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive ¢ EN 301 893 Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive ¢ EN 301 489-17 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment ¢ EN 301 489-1 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements
¢ When entering sleep mode (backlight off), the system will shut down after a week (typical) of time.
62

TAIWAN

° °
°

USA
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ¢ Reorient or relocate the receiving antenna. ¢ Increase the separation between the equipment and receiver. ¢ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. ¢ Consult the dealer or an experienced radio/TV technician for help. FCC Caution:Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5GHz products are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note:The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.
63

CANADA
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
64

MEXICO
Cofetel notice is: (Mexico COFETEL aviso:)
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.”
BRAZIL
ANATEL RF STATEMENT
Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a visible location “Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.”
ANATEL BODY SAR STATEMENT
“Este produto atende aos requisitos técnicos aplicados, incluindo os limites de exposição da Taxa de Absorção Específica referente a campos elétricos, magnéticos e eletromagnéticos de radiofrequência, de acordo com as resoluções n°303/2002 e 533/2009. Este produto atende às diretrizes de exposição à RF na posição normal de uso a pelo menos X centímetros longe do corpo, tendo sido os ensaios de SAR para corpo realizado a X cm de acordo com o informativo de recomendação apresentado no manual do fabricante.”
KOREAN

FCC NOTICE
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
65

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
NOTICE: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. It is the responsibility of the user to correct such interference
WEEE DECLARATION
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
66

WEEE DECLARATION FOR INDIA
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling in India, please visit the below web link. www.aocindia.com/ewaste.php.
EPA ENERGY STAR
ENERGY STAR® is a U.S. registered mark.As an ENERGY STAR® Partner,AOC International (Europe) BV and Envision Peripherals, Inc. have determined that this product meets the ENERGY STAR® guidelines for energy efficiency. (FOR EPA CERTIFIED MODELS)
67

SERVICE
WARRANTY STATEMENT FOR EUROPE
LIMITED THREE-YEAR WARRANTY For AOC LCD Monitors sold within Europe,AOC International (Europe) B.V. warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase. During this period,AOC International (Europe) B.V. will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below. In the absent of the proof of purchase, the warranty will start 3 months after the date of manufacturing indicated on the product.
If the product appears to be defective, please contact your local dealer or refer to the service and support section on www.aoc-europe.com for the warranty instructions in your country.The freight cost for the warranty is pre-paid by AOC for the delivery and return. Please ensure you provide a dated proof of purchase along with the product and deliver to the AOC Certified or Authorized Service Center under the following condition:Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to protects your monitor well enough during transport).
v Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to protects your monitor well enough during transport).
v Put the RMA number on the address label. v Put the RMA number on the shipping carton.
AOC International (Europe) B.V. will pay the return shipping charges within one of the countries specified within this warranty statement. AOC International (Europe) B.V. is not responsible for any costs associated with the transportation of product across international borders.This includes the international border within the European Union. If the LCD Monitor is not available for collection when the currier attends, you will be charged a collection fee. * This limited warranty does not cover any losses or damages that occur as a result of:
v Damages during transport due to improper packaging v Improper installation or maintenance other then in accordance with AOC’s user manual v Misuse v Neglect v Any cause other than ordinary commercial or industrial application v Adjustment by non-authorized source v Repair, modification, or installation of options or parts by anyone other than an AOC Certified
or Authorized Service Center v Improper environments like humidity, water damage and dusts v Damaged by violence, earthquake and terrorist attacks v Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or
other irregularities.
68

This limited warranty does not cover any of the product firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modifications or alteration.
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
If your warranty has expired, you still have access to all available service options, but you will be responsible for the cost of service, including parts, labor, shipping (if any) and applicable taxes.AOC Certified or Authorized Service Center will provide you with an estimate of service costs before receiving your authorization to perform service.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) B.V. LIABILITY,WHETHER BASED ON CONTRACT,TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL AOC INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,YOU MAY HAVE OTHER RIGHTS,WHICH MAY VARY FROM COUNTRY TO COUNTRY.THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice. For more information, please visit: http://www.aoc-europe.com
69

WARRANTY STATEMENT FOR MIDDLE EAST AND AFRICA (MEA) AND
The Commonwealth of Independent States (CIS)
LIMITED ONE to THREE YEARS WARRANTY For AOC LCD Monitors sold within the Middle East and Africa (MEA) and the Commonwealth of Independent States (CIS), AOC International (Europe) B.V. warrants this product to be free from defects in material and workmanship for a period of One (1) to Three (3) years from the manufacture date depending on sale country. During this period,AOC International (Europe) B.V. offers a Carry-In (return to Service Center) Warranty Support at an AOC’s Authorized Service Center or Dealer and at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below. As a Standard Policy, the warranty will be calculated from the manufacture date identified from the product ID serial number, but the total warranty will be Fifteen (15) months to Thirty Nine (39) months from MFD (manufacture date) depending on sale country.Warranty will be considered for exceptional cases that are out of warranty as per the product ID serial number and for such exceptional cases; Original Invoice/Proof Of Purchase Receipt is mandatory.
If the product appears to be defective, please contact your AOC authorized dealer or refer to the service and support section on AOC’s website for the warranty instructions in your country: Egypt: http://aocmonitorap.com/egypt_eng
v CIS Central Asia: http://aocmonitorap.com/ciscentral v Middle East: http://aocmonitorap.com/middleeast v South Africa: http://aocmonitorap.com/southafrica v Saudi Arabia: http://aocmonitorap.com/saudiarabia
Please ensure you provide a dated proof of purchase along with the product and deliver to the AOC Authorized Service Center or Dealer under the following condition:
v Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to protects your monitor well enough during transport).
v Put the RMA number on the address label v Put the RMA number on the shipping carton * This limited warranty does not cover any losses or damages that occur as a result of: v Damages during transport due to improper packaging v Improper installation or maintenance other then in accordance with AOC’s user manual v Misuse v Neglect v Any cause other than ordinary commercial or industrial application v Adjustment by non-authorized source v Repair, modification, or installation of options or parts by anyone other than an AOC Certified
70

or Authorized Service Center v Improper environments like humidity, water damage and dusts v Damaged by violence, earthquakes and terrorist attacks v Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or
other irregularities
This limited warranty does not cover any of the product firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modifications or alteration.
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
If your warranty has expired, you still have access to all available service options, but you will be responsible for the cost of service, including parts, labor, shipping (if any) and applicable taxes.AOC Certified,Authorized Service Center or dealer will provide you with an estimate of service costs before receiving your authorization to perform service.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF ONE (1) to THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATED HERE.AOC INTERNATIONAL (EUROPE) B.V. LIABILITY,WHETHER BASED ON CONTRACT,TORT,WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL AOC INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,YOU MAY HAVE OTHER RIGHTS,WHICH MAY VARY FROM COUNTRY TO COUNTRY.THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice. For more information, please visit: http://www.aocmonitorap.com
71

AOC International (Europe) B.V. Prins Bernhardplein 200 / 6th floor,Amsterdam,The Netherlands
7HOv)D[

July 25th, 2013

AOC PIXEL POLICY ISO 9241-307 CLASS 1

AOC strives to deliver the highest quality products.We use some of the industry’s most advanced manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on the TFT monitor panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but AOC guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This Pixel Policy explains the different types of pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT monitor panel must exceed these acceptable levels.

Pixels and Sub Pixel Definition

A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue.When all sub pixels of pixel are lit, the three colored sub pixel together appear as a single white pixel.When all are dark, the three colored sub pixels together appear as a single black pixel.

Types of Pixel Defects
v Bright Dot Defects: the monitor displays a dark pattern, sub pixels or pixels are always lit or “on” v Black Dot Defects: the monitor displays a light pattern, sub pixels or pixels are always dark or
“off “.

ISO 9241-307 Defect Type 1 Defect Type 2

Pixel Defect Class Bright Pixel

Black Pixel

Class 1

1

Defect Type 3 Bright Sub pixel

Defect Type 4 Black Sub pixel

2

1

3

0

5

AOC International (Europe) B.V.

72

WARRANTY STATEMENT FOR NORTH & SOUTH AMERICA (EXCLUDING BRAZIL)
WARRANTY STATEMENT for AOC Color Monitors Including those Sold within North America as Specified Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original date of consumer purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. ) will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below.The parts or product that are replaced become the property of EPI.
In the USA to obtain service under this limited warranty, call EPI for the name of the Authorized Service Center closest to your area. Deliver the product freight pre-paid, along with the dated proof of purchase, to the EPI Authorized Service Center. If you cannot deliver the product in person:
v Pack it in its original shipping container (or equivalent) v Put the RMA number on the address label v Put the RMA number on the shipping carton v Insure it (or assume the risk of loss/damage during shipment) v Pay all shipping charges
EPI is not responsible for damage to inbound product that was not properly packaged. EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is not responsible for any costs associated with the transportation of product across international borders.This includes the international borders of the countries within this warranty statements.
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free number 888-662-9888. Or you can request an RMA Number online at www.aoc. com/na-warranty. This limited warranty does not cover any losses or damages that occur as a result of:
v Shipping or improper installation or maintenance v Misuse v Neglect v Any cause other than ordinary commercial or industrial application v Adjustment by non-authorized source v Repair, modification, or installation of options or parts by anyone other than an EPI Authorized
Service Center v Improper environment v Excessive or inadequate heating or air conditioning or electrical power failures, surges, or
other irregularities
73

This three-year limited warranty does not cover any of the product’s firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE. EPI’ LIABILITY,WHETHER BASED ON CONTRACT,TORT.WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
In the United States of America, this limited warranty is only valid for Products purchased in the Continental United States, Alaska, and Hawaii. Outside the United States of America, this limited warranty is only valid for Products purchased in Canada. Information in this document is subject to change without notice. For more details, please visit:
v USA: http://us.aoc.com/support/find_service_center v ARGENTINA: http://ar.aoc.com/support/find_service_center v BOLIVIA: http://bo.aoc.com/support/find_service_center v CHILE: http://cl.aoc.com/support/find_service_center v COLOMBIA: http://co.aoc.com/support/find_service_center v COSTA RICA: http://cr.aoc.com/support/find_service_center v DOMINICAN REPUBLIC: http://do.aoc.com/support/find_service_center v ECUADOR: http://ec.aoc.com/support/find_service_center v EL SALVADOR: http://sv.aoc.com/support/find_service_center v GUATEMALA: http://gt.aoc.com/support/find_service_center v HONDURAS: http://hn.aoc.com/support/find_service_center v NICARAGUA: http://ni.aoc.com/support/find_service_center v PANAMA: http://pa.aoc.com/support/find_service_center
74

v PARAGUAY: http://py.aoc.com/support/find_service_center v PERU: http://pe.aoc.com/support/find_service_center v URUGUAY: http://pe.aoc.com/support/find_service_center v VENEZUELA: http://ve.aoc.com/support/find_service_center v IF COUNTRY NOT LISTED: http://latin.aoc.com/support/find_service_center

EASE PROGRAME

Only for AOC branded monitors sold within the continental United States. All AOC branded monitors are now covered by the EASE Program. If your monitor malfunctions at any time during the first three months, AOC will provide a replacement monitor within 72 hours after you are approved for our program. If your monitor qualifies for the EASE program, AOC will pay for freight both ways. Step 1: Phone our TECH Department at 888.662.9888. Step 2: Fill out and return EASE registration forms by mail or fax. Step 3: We will issue a Return Authorization Number upon verification into the program. Step 4: A monitor will be advance shipped to your location. Step 5: We will issue a UPS Call Tag to pick up the defective unit. Step 6: Please review the following chart to see your EASE program qualifications.

WARRANTY PERIOD

COVERAGE AT NO CHARGE

CUSTOMER CHARGES

Within the first three months – New AOC monitor of purchase: Covered by EASE – Call tag dispatched and
return freight charges via UPS

– None*

Between 4 months 1 Year – All Parts & Labor Including – UPS Return Freight to AOC CRT Tube & LCD Panel

Between 1 Year – 3 Years:

– Parts & Labor (excluding

Covered by standard limited CRT Tube & LCD Panel)

warranty

– UPS Return Freight to AOC

*AOC will need to obtain a credit card number if you would like to get a new AOC monitor advanced shipped to your location, prior to the defective unit arriving at AOC’s service center. If you do not wish to supply a credit card, AOC will only ship the new monitor, once the defective unit arrives at the AOC service center.

www.aocmonitor.com
75