VEVOR Air Hydraulic Bottle Jack User Manual
- June 13, 2024
- VEVOR
Table of Contents
Technical Support and E-Warranty Certificate
www.vevor.com/support
BOTTLE JACK
Air Hydraulic Bottle Jack
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only
represents an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and doses not necessarily mean to
cover all categories of tools offered by us. You are kindly reminded to verify
carefully when you are placing an order with us if you are actually saving
half in comparison with the top major brands.
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
Lifting
-
Assemble 2 pc Handle, ensure that spring clips align with slots
-
Secure the load to prevent inadvertent shifting and movement.
-
Position the jack near desired lift paint.
-
Close the release valve by turning it clockwise until it is firmly closed.
CAUTION:
USE THE HANDLE PROVIDED FOR THIS PRODUCT OR AN AUTHORIZED REPLACEMENT HANDLE TO ENSURE PROPER RELEASE VALVE OPERATION. DO NOT USE AN EXTENDER ON THE AIR HOSE NOR THE OPERATING HANDLE WHEN USING IT TO LIFT VEHICLE. LIFT ONLY ON THE MANUFACTURERS RECOMMENDED LIFT POINT AND IN ACCORDANCE WITH THE PUBLISHED GUIDELINES IN YOUR VEHICLE OWNER’S MANUAL. ALWAYS USE JACK STANDS TO SUPPORT THE LOAD IMMEDIATELY AFTER LIFTING.. -
Insert and secure handle into handle sleeve. Pump handle or squeeze the lift control valve until saddle contacts load. To end air operation, simply release the grip on the lift control valve. NEVER WIRE CLAMP OR OTHERWISE DISABLE THE LIFT CONTROL VALVE TO FUNCTION BY ANY MEANS OTHER THAN BY USING THE OPERATOR’S HAND.
-
Raise load to desired height, then immediately transfer the load to appropriately-rated support devices such as jack stands.
WARNING
THIS IS A LIFTNG DEVICE ONLY. IT IS DESIGNED TO LIFTPART OF THE TOTAL VEHICLE
(ONE WHEEL OR AXLE.ALWAYS WEAR SAFETY GLASSES WHEN USING THIS EQUIPMENT CENTER
LOAD ON SADDLE BEFORE LIFTING. NEVER WORK ON,UNDER OR AROUND LOAD UNTIL IT IS
PROPERLY SUPPORTED,TRANSFER THE LOAD IMMEDIATELY TO APPROPRIATE LYRATED JACK
STANDS DO NOT
USE THIS PRODUCT FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS INTENDED. IT IS OWNER’S RESPONSIBILITY TO KEEP LABELS AND MANUALS ARE AVAILABLE FROM THE MANUFACTURER FAILURE TO HEED THESE AND ALL OTHER WARNINGS PERTAINING TO THIS PRODUCT CAN RESULT IN SUDDEN LOSS OF LIFTED LOAD RESULTING IN DEATH PERSONAL INJURY OR PROPERTY DAMAGE.
Lowering
-
Raise load enough to carefully remove jack stands.
-
Insert handle onto release valve and slowly turn handle counterclockwise, but no more than 1/2 turn. If load fails to lower, carefully transfer the load to another lifting device and jack stands. Carefully remove affected jack,and then the jack stands. Lower the load, again by slowly turning the release valve no more than 1/2 turn.
WARNING
BE SURE ALL TOOLS AND PERSONNEL ARE CLEAR BEFORE LOWERING LOAD，DANGEROUS DYNAMIC SHOCK LOADS ARE CREATED BY QUICKLY OPENING AND CLOSING THE RELEASE VALVE AS THE LOAD IS BEING LOWERED THE RESULTING OVERLOAD MAY CAUSE HYDRAULIC SYSTEM FAILURE,WHICH COULD CAUSE SEVERE PERSONAL INJURY AND/OR PROPERTY DAMAGE. -
After removing jack from under the load, push ram and handle sleeve dawn to reduce exposure to rust and contamination
MAINTENANCE
Important: Use only a good grade hydraulic jack oil. Avoid mixing different
types of fluid and NEVER use brake fluid turbine oil, transmission fluid,
motor oil or glycerin. Improper fluid can cause premature failure of the jack
and the potential for sudden and immediate loss of load.
Adding oil
- With saddle fully lowered and pump piston fully depressed, set jack in its upright, level position. Remove oil filler plug.
- Fill until oil is level with the filler plug hole, reinstall oil filter plug.
Changing oil
For best performance and longest life , replace the complete fluid supply at
least once per year.
-
With saddle fully lowered and pump piston fully depressed, remove the oil filler plug.
-
Lay the jack, on its side and drain the fluid into a suitable container.
Note: Dispose of hydraulic fluid in accordance with local regulations -
Fill with good quality jack oil. Reinstall oil filler Plug. We recommend Mobil DTE 13 or equivalent.
Lubrication
-
A coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure that wheels, casters and pump assemblies move freely.
-
Periodically check the pump piston and ram for signs of rust or corrosion.
Clean as needed and wipe with an oily cloth.
NEVER USE SANDPAPER OR ABRASIVE MATERIAL ON THESE SURFACES. -
When not in use, store the jack with pump piston and ram fully retracted.
WARNING
DO NOT ADJUST THIS VALVE
TROUBLE SHOOTING
| Symptom | Possible Causes | Corrective Action |
|---|---|---|
| Jack will not it load | Release valve not tightly closed overload condition | |
| Air supply in adequate | Ensure release valve tightly closed Remedy overload |
condition Ensure adequate air supply
Jack bleeds off after lift| Release valve not tightly closed Overload
condition Hydraulic unit malfunction| Ensure release valve tightly closed
Remedy overload condition Contact seller
Jack will not lower after unloading| Reservoir overfilled Linkages binding|
Drain fluid to proper level Clean and lubricate moving parts
Poor lift performance| Fluid level low Air trapped in system| Ensure proper
fluid level With ram fully retracted, remove oil filler plug to let
pressurized air escape, reinstall oil filler plug
Will not lift to full extension| Fluid level low| Ensure proper fluid level
Parameter table
Model| Lifting Capacity
(TON)| Min Altitude (mm)| Lifting Altitude
(mm)| Regulating Altitude
(mm)| Working air pressure (Mpa)| Air inlet
connector type| Net Weight (kg)
---|---|---|---|---|---|---|---
QJD-Q01
-020A| 20| 265| 175| 60| 0.5| 20PM| 15.
Structural composition
PARTS LIST
| ITEM No. | DESCRIPTION | QTY | ITEM No. | DESCRIPTION | Q’TY | |
|---|---|---|---|---|---|---|
| 1 | SCREW | 1 | 35 | SEAL | 1 | |
| 2 | NUT | 1 | 36 | SCREW | 1 | |
| 3 | PISTON ROD | 1 | 37 | AIR-PISTON PUMP | 1 | |
| 4 | TOP TANK | 1 | 38 | V-SEAL | 2 | |
| 5 | 0-RING | 1 | 39 | BACK-UP RING | 1 | |
| 6 | SEAL A | 1 | 40 | STOP RING | 1 | |
| 7 | PISTON TANK | 1 | 41 | BOLT | 6 | |
| 8 | BACK-UP RING | 1 | 42 | AIR-BASE | 1 | |
| 9 | 0-RING | 1 | 43 | 0-RING | 2 | |
| 10 | CYLINDER | 1 | 44 | NUT | 1 | |
| 11 | OIL TANK | 1 | 45 | COVER OF AIR-PISTON PUMP | 1 | |
| 12 | SEAL B | 1 | 46 | COMPRESSION SPRING | 1 | |
| 13 | GASKET | 1 | 47 | AIR-PISTON | 1 | |
| 14 | OIL-FILTER SCREEN | 1 | 48 | SPRING COVER | 1 | |
| 15 | OIL TANK | 1 | 49 | SEAL | 2 | |
| 16 | PIN | 1 | 50 | AIR-PISTON A | 1 | |
| 17 | RELEASE VALVE | 1 | 51 | 0-RING | 1 | |
| 18 | PIN | 1 | 52 | 0-RING | 1 | |
| 19 | STEEL BALL | 3 | 53 | PISTON | 1 | |
| 20 | BASE | 1 | 54 | AIR-PISTON B | 1 | |
| 21 | SCREW | 2 | 55 | BOLT | 3 | |
| 22 | GASKET | 1 | 56 | SEAL | 1 | |
| 23 | PISTON PUMP | 1 | 57 | STEEL BALL | 6 | |
| --- | --- | --- | --- | --- | --- | --- |
| 24 | 0-RING | 1 | 58 | AIR CYLINDER | 1 | |
| 25 | BACK-UP RING | 1 | 59 | STEEL BALL | 3 | |
| 26 | PISTON | 1 | 60 | BOLT | 3 | |
| 27 | WIRE PIN | 2 | 61 | AIR-TOP TANK | 1 | |
| 28 | PIN | 2 | 62 | AIR INCOME BOLT | 1 | |
| 29 | PIN | 1 | 63 | 0-RING | 2 | |
| 30 | TIE | 1 | 64 | ROTATING SLEEVE | 1 | |
| 31 | HANDLE | |||||
| SOCKET | 1 | 65 | C-RING | 1 | ||
| 32 | HANDLE-UP PER | 1 | 66 | BOLT | 2 | |
| 33 | HANDLE-LO WER | 1 | 67 | EXTENTION SPRING | 2 | |
| 34 | BOLT | 1 | 68 | SPRING BASE | 1 |
Technical Support and E-Warranty Certificate
https://www.vevor.com/support
Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>